On PIIX4, function 3, the PMREGMISC register at offset 0x80, with
default value 0x00 has its bit 0 (PMIOSE) indicate whether the PM
IO space given in the PMBA register (offset 0x40) is enabled.
PMBA must be configured *before* setting this bit.
On Q35/ICH9+, function 0x1f, the equivalent role is fulfilled by
bit 7 (ACPI_EN) in the ACPI Control Register (ACPI_CNTL) at offset
0x44, also with a default value of 0x00.
Currently, OVMF hangs when Q35 reboots, because while PMBA is reset
by QEMU, the register at offset 0x80 (matching PMREGMISC on PIIX4)
is not reset, since it has a completely different meaning on LPC.
As such, the power management initialization logic in OVMF finds
the "PMIOSE" bit enabled after a reboot and decides to skip setting
PMBA. This causes the ACPI timer tick routine to read a constant
value from the wrong register, which in turn causes the ACPI delay
loop to hang indefinitely.
This patch modifies the Base[Rom]AcpiTimerLib constructors and the
PlatformPei ACPI PM init routines to use ACPI_CNTL:ACPI_EN instead
of PMREGMISC:PMIOSE when running on Q35.
Reported-by: Reza Jelveh <reza.jelveh@tuhh.de>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17076 6f19259b-4bc3-4df7-8a09-765794883524
Link DXE_SMM_DRIVER, UEFI_DRIVER, UEFI_APPLICATION, and SMM_CORE against
a valid, non-asserting version of PcdLib, then switch them over to using
the "Dxe" instance of AcpiTimerLib (instead of the "Base" version).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16378 6f19259b-4bc3-4df7-8a09-765794883524
Since in OVMF both PEI_CORE and PEIM run from RAM, and thus may
utilize global variables, use the "Base" AcpiTimerLib instance
(instead of BaseRom) to take advantage of the improved efficiency
of storing the timer register IO address in a global variable.
This leaves only SEC using the BaseRomAcpiTimerLib instance.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16377 6f19259b-4bc3-4df7-8a09-765794883524
Remove local power management register access macros in favor of
factored-out ones in OvmfPkg/Include/OvmfPlatforms.h
Next, AcpiTimerLib is split out into three instances, for use during
various stages:
- BaseRom: used during SEC, PEI_CORE, and PEIM;
- Dxe: used during DXE_DRIVER and DXE_RUNTIME_DRIVER;
- Base: used by default during all other stages.
Most of the code remains in AcpiTimerLib.c, to be shared by all
instances. The two platform-dependent methods (constructor and
InternalAcpiGetTimerTick) are provided separately by source files
specific to each instance, namely [BaseRom|Base|Dxe]AcpiTimerLib.c.
Since pre-DXE stages can't rely on storing data in global variables,
methods specific to the "BaseRom" instance will call platform
detection macros each time they're invoked.
The "Base" instance calls platform detection macros only from its
constructor, and caches the address required by InternalAcpiTimerTick
in a global variable.
The "Dxe" instance is very similar to "Base", except no platform
detection macros are called at all; instead, the platform type is
read via a dynamic PCD set from PlatformPei.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16376 6f19259b-4bc3-4df7-8a09-765794883524
Pick the appropriate bus:dev.fn for accessing ACPI power management
registers (00:01.3 on PIIX4 vs. 00:1f.0 on Q35) based on the device
ID of the host bridge (assumed always present at 00:00.0).
With this patch, OVMF can boot QEMU's "-machine q35" x86 machine type.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16066 6f19259b-4bc3-4df7-8a09-765794883524
The TimerLib in the OvmfPkg uses a global variable called mPmba and depends on that global being updated. This works for modules loaded into memory, but not XIP modules in ROM/FLASH.
This patch removes the mPmba global variable and instead reads the PIIX4 Power Management Base Address from PCI configuration space when it is needed. This patch also simplifies the initialization logic in the constructor and introduces #defines to eliminate hard coded values in the function implementations. According to the PIIX4 documentation, the IO Space enable bit in the PCI Command Register does not have to be set for the Power Management Base Address to be decoded, so that one op has been removed from the constructor.
I have tested this patch with QEMU and verified that the UDK Debugger us functional when SOURCE_DEBUG_ENABLE is set.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
I also tested it with RHEL-6.3 guest boot/shutdown, Fedora 18 Alpha XFCE
guest boot/shutdown, and Windows 8 Consumer Preview guest
boot/reboot/shutdown. (RHEL-6.3 host.) I didn't notice any adverse effects.
Tested-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13783 6f19259b-4bc3-4df7-8a09-765794883524
The Index Register Base Address bitfield is selected by the binary mask
00000000 00000000 11111111 11000000, 0xFFC0; fix the typo.
Reported-by: Gleb Natapov <gleb@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13720 6f19259b-4bc3-4df7-8a09-765794883524
0xb000 is the address normally used with QEMU.
0x400 also appears to conflict with some debug I/O ports
used by QEMU.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Erik Bjorge <erik.c.bjorge@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Bei Guan <gbtju85@gmail.com>
Reviewed-by: Bei Guan <gbtju85@gmail.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13279 6f19259b-4bc3-4df7-8a09-765794883524
For the first instance of the library that runs, the
base is initialized to 0x400, but we access it at 0x401.
Signed-off-by: jljusten
Reviewed-by: niruiyu
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12121 6f19259b-4bc3-4df7-8a09-765794883524
If PIIX4 Power Management Base Address (PMBA) is already
programmed, then read and use it's current setting.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: gavinguan
Signed-off-by: jljusten
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12053 6f19259b-4bc3-4df7-8a09-765794883524
Gabriel Somlo
mdkinney
jljusten
xdu2
hhtian
lgao4
klu2