Remove the RecoveryOemHookLib class and instance that is no
longer used by any modules.
Cc: Kelly Steele <kelly.steele@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=138
Add the ForceRecovery UEFI application to the Quark.dsc file
so this application can be put onto an SD card or USB drive
to test the Galileo firmware recovery feature.
The library mappings to the RecoveryOemHookLib are also
removed becuse this library is not longer used by any modules.
Cc: Kelly Steele <kelly.steele@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
Remove the library function PlatformDebugPortGetChar8() from the
PlatformHelperLib that is no longer used by any modules.
Cc: Kelly Steele <kelly.steele@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=137https://bugzilla.tianocore.org/show_bug.cgi?id=139
There are four supported methods to generate a boot mode of
BOOT_IN_RECOVERY_MODE on the Galileo platforms:
* Detect a corrupt FV
* Detect a forced recovery from the ForceRecovery UEFI application
that sets a bit in a sticky R/W register
* The RESET button for the Arduino shield is held while the system
is powered up
* The RESET button for the Arduino shield is held while the system
is rebooted using the REBOOT button.
The logic in the PlatformInit module is cleaned up and updated to
support all three of the recovery detection methods. The clean
ups include:
* Remove extra debug messages
* Remove user input from serial port
In addition, once one of the recovery methods is detected and a
boot mode of BOOT_IN_RECOVERY_MODE is set, the Galileo platforms
would get an error attempting to use the USB host controller to
detect and read a recovery image from a USB drive. The issue is
the IMR protection registers are programmed to prevent DMA to
memory owned by the PEI Core. The IMR register programming is
updated to allow DMA to memory that is allocated by the recovery
modules using the PEI AllocatePages() service.
Cc: Kelly Steele <kelly.steele@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=138
This UEFI Application sets a sticky bit that persists across reset
to force a boot mode of BOOT_IN_RECOVERY_MODE. It then performs
a warm reset using the UEFI Runtime Service ResetSystem().
Cc: Kelly Steele <kelly.steele@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
ESP should be set to top of eSRAM range that aligns with Flat32.asm. Because CPU
BIST data will be located at top of STACK, this issue leads Platform Sec Lib
cannot get the correct CPU BIST information.
This fix is to address below issue:
https://tianocore.acgmultimedia.com/show_bug.cgi?id=123
Cc: Steven Shi <Steven.shi@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Kelly Steele <kelly.steele@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
PiDxeS3BootScriptLib will be updated to consume PciSegmentLib
instead of PciLib to support multiple PCI segment.
That means platforms need to add PciSegmentLib
declaration in platform dsc if the PciSegmentLib was
not declared in platform dsc before.
For platforms only have one segment,
MdePkg/Library/BasePciSegmentLibPci/BasePciSegmentLibPci.inf is recommended
to be used and declared in platform dsc for PiDxeS3BootScriptLib to have
equivalent functionality with before.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Amy Chan <amy.chan@intel.com>
Cc: Kelly Steele <kelly.steele@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
This update is for CpuDxe consuming MP Initialize library.
v5:
1. Update Quark DSC files to add PeiMpInitLib.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Kelly Steele <kelly.steele@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
A number of code locations use
ASSERT_EFI_ERROR (BooleanExpression)
instead of
ASSERT (BooleanExpression)
Fix them.
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Kelly Steele <kelly.steele@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Fix variable set but not used errors detected by GCC 4.8.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Fix build errors detected with GCC 4.8.4: local variable set but not
used!
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Remove the PlatformFlashEraseWrite function which is not used within
CorebootPayloadPkg.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-by: Prince Agyeman <prince.agyeman@intel.com>
Add the TcgSmm and TcgMor modules that are required to manage
UEFI variable that conveys TCG MOR request to memory init module
in PEI phase.
Cc: Kelly Steele <kelly.steele@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19777 6f19259b-4bc3-4df7-8a09-765794883524
If TCG Memory Overwrite Request is set, then clear all memory
available for use by an OS. An OS may optionally use embedded
SRAM in Quark SoC X1000, so the embedded SRAM should is cleared
too. TCG MOR requests are communicated through a UEFI variable.
This module reads UEFI variable to check state of MOR request.
Cc: Kelly Steele <kelly.steele@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19776 6f19259b-4bc3-4df7-8a09-765794883524
Add a Readme.md for the QuarkPlatformPkg that describes how to
clone, build, boot, debug, and enable/disable features for the
Intel(R) Galileo Development Board and the Intel(R) Galileo Gen 2
Development Board.
Cc: Kelly Steele <kelly.steele@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19764 6f19259b-4bc3-4df7-8a09-765794883524
Add MEASURED_BOOT_ENABLE flag
Add TPM_12_HARDWARE flag
Add TrEEConfigPei to detect TPM 1.2 hardware device
Use Tpm12DeviceLib instance for Atmel I2C TPM
Use Tpm12DeviceLib instance for Infineon I2C TPM
Add TcgPei and TcgDxe modules for TPM 1.2 support
Clean up TpmMeasurementLib mappings
Cc: Kelly Steele <kelly.steele@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19732 6f19259b-4bc3-4df7-8a09-765794883524
Add new Tpm12DeviceLib instance for an Atmel I2C TPM
Cc: Kelly Steele <kelly.steele@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19730 6f19259b-4bc3-4df7-8a09-765794883524
Rename the Ui libraries,so need to update the QuarkPlatformPkg.dsc file.
Cc: Kelly Steele <kelly.steele@intel.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
Reviewed-by: Dandan Bi <dandan.bi@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19720 6f19259b-4bc3-4df7-8a09-765794883524
Remove GPIO expander configuration actions that are now performed in
PEI Phase in PlatformInit module. In order to detect physical presence
only the state of the Reset Button needs to be read.
Cc: Kelly Steele <kelly.steele@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19621 6f19259b-4bc3-4df7-8a09-765794883524
Configure GPIO expander in PEI phase
1) Configure all GPIO expander pins connected to Reset Button as inputs
2) Configure multiplexer for I2C to route I2C bus to Arduino Header
Cc: Kelly Steele <kelly.steele@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19620 6f19259b-4bc3-4df7-8a09-765794883524
The functions used to manage the PCAL GPIO I2C expander are located
in a DXE specific source file. Move these functions to a source
file that is common to both the PEI and DXE versions of this library
so these GPIO pins can be managed from PEIMs.
Cc: Kelly Steele <kelly.steele@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19619 6f19259b-4bc3-4df7-8a09-765794883524
Update memory bin sizes in Memory Type Information on first boot after
FLASH update to avoid reboot when memory bins are too small when all
features are enabled.
Cc: Kelly Steele <kelly.steele@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19618 6f19259b-4bc3-4df7-8a09-765794883524
Update Flat32.S to match Flat32.asm. A sync was missed, so
Flat32.S is calling SecStartup instead of PlatformSecLibStartup
which is causing a boot failures with GCC builds because the
caches are not initialized correctly when the call to
PlatformSecLibStartup is not performed.
Cc: Kelly Steele <kelly.steele@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19306 6f19259b-4bc3-4df7-8a09-765794883524
Remove declaration of gEfiFirmwareVolumeBlockProtocolGuid and
gEfiSmmFirmwareVolumeBlockProtocolGuid that are generating build
failures on GCC because these same variables are declared in
AutoGen.c and assigned a GUID value from DEC file.
Cc: Kelly Steele <kelly.steele@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Kelly Steele <kelly.steele@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19305 6f19259b-4bc3-4df7-8a09-765794883524
Changes for V4
==============
1) Move delete of QuarkSocPkg\QuarkNorthCluster\Binary\QuarkMicrocode
from QuarkPlatformPkg commit to QuarkSocPkg commit
2) Fix incorrect license header in PlatformSecLibModStrs.uni
Changes for V3
==============
1) Set PcdResetOnMemoryTypeInformationChange FALSE in QuarkMin.dsc
This is required because QuarkMin.dsc uses the emulated variable
driver that does not preserve any non-volatile UEFI variables
across reset. If the condition is met where the memory type
information variable needs to be updated, then the system will reset
every time the UEFI Shell is run. By setting this PCD to FALSE,
then reset action is disabled.
2) Move one binary file to QuarkSocBinPkg
3) Change RMU.bin FILE statements to INF statement in DSC FD region
to be compatible with PACKAGES_PATH search for QuarkSocBinPkg
Changes for V2
==============
1) Use new generic PCI serial driver PciSioSerialDxe in MdeModulePkg
2) Configure PcdPciSerialParameters for PCI serial driver for Quark
3) Use new MtrrLib API to reduce time to set MTRRs for all DRAM
4) Convert all UNI files to utf-8
5) Replace tabs with spaces and remove trailing spaces
6) Add License.txt
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Acked-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19287 6f19259b-4bc3-4df7-8a09-765794883524
Changes for V4
==============
1) Remove Unicode character from C source file
2) Move delete of QuarkSocPkg\QuarkNorthCluster\Binary\QuarkMicrocode
from QuarkPlatformPkg commit to QuarkSocPkg commit
Changes for V2
==============
1) Sync with new APIs in SmmCpuFeaturesLib class
2) Use new generic PCI serial driver PciSioSerialDxe in MdeModulePkg
3) Remove PCI serial driver from QuarkSocPkg
4) Apply optimizations to MtrrLib from MtrrLib in UefiCpuPkg
5) Convert all UNI files to utf-8
6) Replace tabs with spaces and remove trailing spaces
7) Add License.txt
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Acked-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19286 6f19259b-4bc3-4df7-8a09-765794883524
Michael Kinney
Jeff Fan
Star Zeng
Laszlo Ersek
Lee Leahy