For setting high speed in SD card,
First CMD 6 (Switch) is send to check if card supports High Speed and
Second command is send to switch card to high speed mode.
In current inplementation, CMD 6 was sent only once to switch the
card into HS mode without checking if card supports HS or not, which is
not as per specification and also we are not setting the HS i.e. 50000000
but directly asking the card to switch to 26000000 which is incorrect as
SD card supports either 25000000 or 50000000.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
We want to print name of the function resulted in error,
but __FUNCTION__ macro was missing.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
ExtCSD structure may be read via DMA. So align it to
page to avoid data corruption.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The argument of CMD8 should be stuff bits according to standard
JESD84-A44.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Only DDR mode is support for 8bit mode currently. Add
non-DDR case when configuring ECSD.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Add the interface to change the bus width and speed.
By default, MMC is initialized with 1-bit mode and less than 400KHz bus
clock. It causes MMC working inefficiently.
Set I/O bus width on both MMC controller and EXTCSD. Otherwise, it may
cause unmatched failure case. And support more timing mode, high speed,
HS200 & HS400 mode.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Declare fields in ECSD structure. And drop the original 128 words
arrary.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Since ECSD also describes the information of card, move it into
structure CardInfo.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
According to eMMC spec, OCR.PowerUp bit is also busy bit. If the busy
bit is '0', CMD1 should be sent and OCR should be fetched again. And add
a timeout counter on the repeated steps.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
UEFI drivers should not depend on TimerLib. They should
use BS.Stall() instead.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17343 6f19259b-4bc3-4df7-8a09-765794883524
Meenakshi Aggarwal
Jun Nie
Haojian Zhuang
Olivier Martin