Every CPUs have their own initialization requirements.
This library allows to allows to abstract these initialization requirements
into the ARM Platform common components.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12448 6f19259b-4bc3-4df7-8a09-765794883524
In the previous version, every cores had the same stack size.
To avoid to waste memory with secondary core stacks, the primary core stack
size is now different from the secondary cores stack size.
These are the Stack PCDs and their default values:
gArmPlatformTokenSpaceGuid.PcdCPUCoresSecStackBase|0
gArmPlatformTokenSpaceGuid.PcdCPUCoreSecPrimaryStackSize|0x10000
gArmPlatformTokenSpaceGuid.PcdCPUCoreSecSecondaryStackSize|0x1000
gArmPlatformTokenSpaceGuid.PcdCPUCoresSecMonStackBase|0
gArmPlatformTokenSpaceGuid.PcdCPUCoreSecMonStackSize|0x1000
gArmPlatformTokenSpaceGuid.PcdCPUCoresStackBase|0
gArmPlatformTokenSpaceGuid.PcdCPUCorePrimaryStackSize|0x10000
gArmPlatformTokenSpaceGuid.PcdCPUCoreSecondaryStackSize|0x1000
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12415 6f19259b-4bc3-4df7-8a09-765794883524
This library is the interface for the ARM Generic Interrupt Controller
Architecture Specification.
ARM Platform can use any GIC controller (not necessary PL390 GIC).
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12411 6f19259b-4bc3-4df7-8a09-765794883524
This library that uses the DebugAgentLib interface prints the loaded addresses
of the SEC and PEI_CORE module using PeCoffExtraActionLib.
Note: Because there is no PE loader for these XIP modules, PeCoffExtraActionLib is not invoked.
This library scans the firmware volume to find these modules and calculate their fixup loaded
addresses used to load their symbols in the debugger.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12023 6f19259b-4bc3-4df7-8a09-765794883524
In the former memory model, the UEFI firmware was expected to be located
at the top of the system memory. Stacks & Pi memory regions were set below
the firmware.
On some platform, the UEFI firmware could be shadowed by the ROM firmware
(case of the BeagleBoard) and in some cases the firmware is copied at the
beginning of the system memory.
With this new memory model, stack and Pi/DXE memory regions are set at the
top of the system memory wherever the UEFI firmware is located in the memory
map.
Because DXE core does not support shadowed firmwares, the system memory covered
by the UEFI firmware is marked as 'Non Present' to avoid to be overlapped by
DXE allocations.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11992 6f19259b-4bc3-4df7-8a09-765794883524
The PcdStandalone is a PCD ARM Ltd uses to make the difference between a standalone UEFI (boot
from cold boot to Boot Manager without user intervention) and a Debug UEFI firmware (the firmware
engineer has to copy the Normale World image into the DRAM to enable his/her firmware).
By coping the firmware into DRAM in the non standalone version it is much faster than reflashing
the NOR Flash after each build.
ArmPlatformSecExtraAction() function is called just before the Sec module jump to normal world.
The platform firmware can run extra actions at this stage.
The 'ARM Standalone' concept has moved to the implementation of ArmPlatformSecExtraAction() for
the ARM development boards (in ArmPlatformPkg/Library/DebugSecExtraActionLib).
ArmPlatformPkg: Enable DebugAgentLib in Sec and PrePeiCore
ArmPlatformPkg: Fix line endings in some source files
Use CR+LF line endings as defined by the EDK2 coding convention
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11991 6f19259b-4bc3-4df7-8a09-765794883524
The $(BUILD_TARGETS) macro was used to make the difference between DEBUG and
RELEASE builds. The $(TARGET) macro should be used instead.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11961 6f19259b-4bc3-4df7-8a09-765794883524
The idea is to keep ArmPkg responsible for the ARM architectural modules and ArmPlatformPkg
the ARM development platform packages (with their respective drivers).
ArmPlatformPkg: Reduce driver dependency on ArmPlatform.h
- Move some driver definitions from C-Macro to PCD values
- Unify PCD driver namespace
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11956 6f19259b-4bc3-4df7-8a09-765794883524
This module is enabled for ArmRealViewEb and ArmvExpress builds
when the macro EDK2_SKIP_PEICORE is passed to the build system.
The PrePi module can be used when the DRAM has already been initialized
by the SEC phase/1st stage boot loader and no call to external PEIM is
required.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11953 6f19259b-4bc3-4df7-8a09-765794883524
Feature PCDs cannot be used in assembly files.
The PcdStandalone PCD is needed in one of the assembly file of the
ArmPlatformPkg/PrePi module.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11952 6f19259b-4bc3-4df7-8a09-765794883524
The size of this memory is controlled by a PCD. The Global Variable in this regsion are defined by their offset.
This memory region can be use to store the PEI Services Table Pointer.
Update the PeiServicesTablePointerLib to use this region instead of PcdPeiServicePtrAddr.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11803 6f19259b-4bc3-4df7-8a09-765794883524
The UEFI Specification defines some requirement related to the Boot Manager.
This new version of the BDS support most of the features:
- TimeOut, BootNext, BootOrder, Boot### environment variable for boot device selection
- ConOut. ConIn, ConErr environment variables for console intialization
- Boot EFI application defined by a Device Path
- Support removable devices
- Support FileSystem, MemMap, PXE and TFTP boot devices
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11800 6f19259b-4bc3-4df7-8a09-765794883524
The UEFI platform designer had to add '%a' to their EBL prompt PCD to print out the path
in the shell.
This change makes the addition of the path automatically after the platform specific value
in the EBL shell.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11798 6f19259b-4bc3-4df7-8a09-765794883524
This driver implements the interface for the PL111 Lcd controller.
The LcdPlatformLib allows to set the platform specific requirements
needed by the platform for setting the LCD (oscillators, etc).
ArmPlatformPkg/ArmVExpressPkg: Implement LcdPlatformLib
This library exports the supported resolutions. It also allocates the
memory for the framebuffer and send the correct settings to the VExpress
motherboard microcontroller.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11786 6f19259b-4bc3-4df7-8a09-765794883524
The purpose of this library is to create an interface to communicate
with the platform micro-controller.
It abstracts the communication protocol (eg: SPI, UART, etc) between
the application processor and the micro-controller.
ArmPlatformPkg/ArmVExpressPkg: Implement ArmPlaformSysConfigLib
This implementation allows to communicate with the microcontroller of the
Versatile Express motherboard.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11785 6f19259b-4bc3-4df7-8a09-765794883524
This file contains the ARM Versatile Express motherboard definitions.
It allows to avoid duplication between different platforms based on ARM VExpress
motherboard.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11749 6f19259b-4bc3-4df7-8a09-765794883524
This NOR Flash driver can be reused for other platform (eg: ARM Realview EB).
To make this driver reusable on other platforms the NorFlashPlatformLib library
has been created to abstract the platform specific bits such as the pre-requirements
steps to the initialization and the geometry of the NOR Flash regions.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11746 6f19259b-4bc3-4df7-8a09-765794883524
This library makes the interface with the PL011 UART controller.
This library can be linked to different types of driver (Serial Console,
debugger, etc) using PL011 UART controller.
ArmPlatformPkg/PL011SerialPortLib: Use Drivers/PL011Uart
Remove the direct accesses to the PL011 UART controller to use the PL011Uart
library.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11743 6f19259b-4bc3-4df7-8a09-765794883524
Formerly, each platform was responsible to declare the location of its UEFI memory
region (used by PEI and DXE Foundations).
The ArmPlatformLib was also declaring every region of its partitionned system memory
with a System Resource HOB.
In this new model, the MemoryInit expects the system memory to be declared with the
PCDs gArmTokenSpaceGuid.PcdSystemMemoryBase/Size.
These PCDs declare the largest continuous DRAM region. Additional regions can be
declared with the ArmPLatformLib function ArmPlatformGetAdditionalSystemMemory().
Now, it is the PEIM that partitions the system memory for every platform. It installs
a region of the size PcdSystemMemoryUefiRegionSize (default 128MB) for the PEI permanent
memory at the top of the DRAM region.
And a region of gArmPlatformTokenSpaceGuid.PcdSystemMemoryFixRegionSize (default 128MB)
is declared at the base of the system memory. This region is used for the allocation that
requires fixed address or have some constraints on their locations.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11481 6f19259b-4bc3-4df7-8a09-765794883524
This function is responsible to handle all the specific platform code that must
be run in secure world to initialize some controllers.
ArmPlatformPkg/Sec: Move the L2x0 initialization to ArmPlatformLib
The L2x0 controller must be initialized in secure world. Move its initialization
into the ArmPlatformInitialize() of the Cortex A9x4 Core Tile PlatformLib.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11476 6f19259b-4bc3-4df7-8a09-765794883524
The Variable Storage is now formated by the NOR Flsah driver.
Force the NOR Flash driver to be loaded before the Variable Service
DXE driver. And check if the Non Volatile Storage exists in NOR flash.
If not, the driver writes the correct header.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11471 6f19259b-4bc3-4df7-8a09-765794883524
oliviermartin
andrewfish