0xb000 is the address normally used with QEMU.
0x400 also appears to conflict with some debug I/O ports
used by QEMU.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Erik Bjorge <erik.c.bjorge@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Bei Guan <gbtju85@gmail.com>
Reviewed-by: Bei Guan <gbtju85@gmail.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13279 6f19259b-4bc3-4df7-8a09-765794883524
If the bit is not set, then the only method ACPI defines
for setting it is to use the SMI SCI enable code path.
Since OVMF does not support SMM, we must enable the
bit during boot.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Erik Bjorge <erik.c.bjorge@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Bei Guan <gbtju85@gmail.com>
Reviewed-by: Bei Guan <gbtju85@gmail.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13278 6f19259b-4bc3-4df7-8a09-765794883524
If –D SECURE_BOOT_ENABLE is specified with the build command, Secure Boot support is enabled including custom mode setup.
This allows Secure Boot to be configured through setup allowing OvmfPkgX64, OvmfPkgIa32 and OvmfPkg3264 to be a fully functional Secure Boot reference platforms.
Remove redundant library class definitions for BaseCryptLib and OpenSslLib.
Signed-off-by: Lee Rosenbaum <lee.g.rosenbaum@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Erik Bjorge <erik.c.bjorge@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13160 6f19259b-4bc3-4df7-8a09-765794883524
For the first instance of the library that runs, the
base is initialized to 0x400, but we access it at 0x401.
Signed-off-by: jljusten
Reviewed-by: niruiyu
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12121 6f19259b-4bc3-4df7-8a09-765794883524
If PIIX4 Power Management Base Address (PMBA) is already
programmed, then read and use it's current setting.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: gavinguan
Signed-off-by: jljusten
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12053 6f19259b-4bc3-4df7-8a09-765794883524
This call can cause a reset, and is most critical for ACPI S3/S4
resume situations. OVMF does not support S3/S4.
OVMF does not have true non-volatile variable support, so
this call could cause a continuous reset situation in certain
scenarios. (The BdsLibSaveMemoryTypeInformation may set an
non-volatile variable, and then reset with the assumption that
the variable will still exist during the next boot.)
Additionally, some version of QEMU appear to hang when the
port 64 reset is initiated.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@10927 6f19259b-4bc3-4df7-8a09-765794883524
Note:
* This only works before ExitBootServices
* For OVMF, variables are only preserved on the disk if there
is a hard disk connected which has a writeable FAT file system.
The Ovmf/Library/EmuVariableFvbLib library will look for the
gUefiOvmfPkgTokenSpaceGuid.PcdEmuVariableEvent PCD to be set to
a non-zero value. If set, it is treated as an event handle, and
each write to the EmuVariableFvb will cause the event to be
signaled.
In this change, the OVMF platform BDS library sets up this event,
and sets the PCD so that after each write to the EMU Variable FVB,
the non-volatile variables will be saved out to the file system.
The end result is that NV variables that are written prior to the
ExitBootServices call should be preserved by storing them on the
disk.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9318 6f19259b-4bc3-4df7-8a09-765794883524
This library provides an interface where variables can be saved and restored
using a file in a file system accessible to the firmware. It is expected
that a platform BDS library will use this library. The platform BDS
implementation can decide which devices to connect and then to attempt to use
for saving and restoring NV variables.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9272 6f19259b-4bc3-4df7-8a09-765794883524
QEMU will automatically fill the video BIOS image into memory at the
legacy video BIOS memory location (0xc0000). This code will look
there for a EFI option rom image, and load it if it found. This
allows the video option ROM to be separated out from the main system
firmware image.
QEMU does not appear to emulate the PCI rom expansion method
for making the video BIOS available to the system.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@8942 6f19259b-4bc3-4df7-8a09-765794883524
It is not proper for a library implementation to assume the names of function in a parent module.
Instead, they must be designed as the pointers to these two BdsDxe functions and passed in.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@8931 6f19259b-4bc3-4df7-8a09-765794883524
jljusten
leegrosenbaum
rsun3
xdu2
mdkinney
lgao4
hhtian
klu2
qhuang8
eric_tian