The OvmfXen platform specifies the dynamic access method for
"PcdPciDisableBusEnumeration" needlessly.
After the DSC file sets the PCD to TRUE by default, the InitializeXen()
function in XenPlatformPei superfluously sets the PCD to TRUE again. There
are no other writes to the PCD in the platform.
Make the PCD Fixed-At-Build, and remove the access (in fact, the whole
InitializeXen() function) from XenPlatformPei.
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Julien Grall <julien@xen.org>
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=2122
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20210526201446.12554-20-lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Calculate the frequency of the APIC timer that Xen provides.
Even though the frequency is currently hard-coded, it isn't part of
the public ABI that Xen provides and thus may change at any time. OVMF
needs to determine the frequency by an other mean.
Fortunately, Xen provides a way to determines the frequency of the
TSC, so we can use TSC to calibrate the frequency of the APIC timer.
That information is found in the shared_info page which we map and
unmap once done (XenBusDxe is going to map the page somewhere else).
The shared_info page is mapped at the highest physical address allowed
as it doesn't need to be in the RAM, thus there's a call to update the
page table.
The calculated frequency is only logged in this patch, it will be used
in a following patch.
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=2490
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20210412133003.146438-7-anthony.perard@citrix.com>
When the device ID of the host bridge is unknown, check if we are
running as a PVH guest as there is no PCI bus in that case.
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1689
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190813113119.14804-26-anthony.perard@citrix.com>
When running as a Xen PVH guest, there is no CMOS to read the memory
size from. Rework GetSystemMemorySize(Below|Above)4gb() so they can
work without CMOS by reading the e820 table.
Rework XenPublishRamRegions to also care for the reserved and ACPI
entry in the e820 table. The region that was added by InitializeXen()
isn't needed as that same entry is in the e820 table provided by
hvmloader.
MTRR settings aren't modified anymore, on HVM it's already done by
hvmloader, on PVH it is supposed to have sane default. MTRR will need
to be done properly but keeping what's already been done by programs
that have run before OVMF will do for now.
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1689
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190813113119.14804-24-anthony.perard@citrix.com>
We are going to need to make an hypercall in order to retreive the E820
table from the hypervisor before been able to setup the memory.
Calling XenConnect earlier will allow to setup the XenHypercallLib
earlier to allow to make hypercalls.
While here, add some comments in XenConnect().
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1689
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190813113119.14804-20-anthony.perard@citrix.com>
Introduce XenPlatformPei, a copy of OvmfPkg/PlatformPei without some
of QEMU specific initialization, Xen does not support QemuFwCfg.
This new module will be adjusted to accommodate Xen PVH.
fw_cfg dependents that have been removed, which are dynamically skipped
when running PlatformPei on Xen:
- GetFirstNonAddress(): controlling the 64-bit PCI MMIO aperture via the
(experimental) "opt/ovmf/X-PciMmio64Mb" file
- GetFirstNonAddress(): honoring the hotplug DIMM area
("etc/reserved-memory-end") in the placement of the 64-bit PCI MMIO
aperture
- NoexecDxeInitialization() is removed, so PcdPropertiesTableEnable and
PcdSetNxForStack are left constant FALSE (not set dynamically from
fw_cfg "opt/ovmf/PcdXxxx")
- MaxCpuCountInitialization(), PublishPeiMemory(): the max CPU count is
not taken from the QemuFwCfgItemSmpCpuCount fw_cfg key;
PcdCpuMaxLogicalProcessorNumber is used intact and
PcdCpuApInitTimeOutInMicroSeconds is never changed or used.
- InitializeXenPlatform(), S3Verification(): S3 is assumed disabled (not
consulting "etc/system-states" via QemuFwCfgS3Enabled()).
- InstallFeatureControlCallback(): the feature control MSR is not set
from "etc/msr_feature_control"
(also removed FeatureControl.c as there is nothing been executed)
Also removed:
- SMRAM/TSEG-related low mem size adjusting (PcdSmmSmramRequire is
assumed FALSE) in PublishPeiMemory(),
- QemuInitializeRam() entirely,
Xen related changes:
- Have removed the module variable mXen, as it should be always true.
- Have the platform PEI initialization fails if Xen has not been
detected.
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1689
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190813113119.14804-5-anthony.perard@citrix.com>
Laszlo Ersek
Anthony PERARD