Tested with the "bootorder" fw_cfg file. Example contents (leading space
added and line terminators transcribed for readability):
/pci@i0cf8/ide@1,1/drive@0/disk@0<LF>
/pci@i0cf8/ide@1,1/drive@1/disk@0<LF>
/pci@i0cf8/ethernet@3/ethernet-phy@0<NUL>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13549 6f19259b-4bc3-4df7-8a09-765794883524
XenInfo HOB is used to pass XenInfo from PEI to DXE.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: gavinguan
Reviewed-by: jljusten
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12059 6f19259b-4bc3-4df7-8a09-765794883524
This library provides an interface for converting the system
variables into a binary and also restoring the system variables
from that binary.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11284 6f19259b-4bc3-4df7-8a09-765794883524
This protocol is similar to the standard UEFI BlockIo protocol,
except it has no function calls and simply defines a base address
in memory where reads & writes for the block device should occur.
One planned usage is to fill a memory region with a small disk
image, and allow it to be used as a normal disk by the
standard drivers.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@10295 6f19259b-4bc3-4df7-8a09-765794883524
Note:
* This only works before ExitBootServices
* For OVMF, variables are only preserved on the disk if there
is a hard disk connected which has a writeable FAT file system.
The Ovmf/Library/EmuVariableFvbLib library will look for the
gUefiOvmfPkgTokenSpaceGuid.PcdEmuVariableEvent PCD to be set to
a non-zero value. If set, it is treated as an event handle, and
each write to the EmuVariableFvb will cause the event to be
signaled.
In this change, the OVMF platform BDS library sets up this event,
and sets the PCD so that after each write to the EMU Variable FVB,
the non-volatile variables will be saved out to the file system.
The end result is that NV variables that are written prior to the
ExitBootServices call should be preserved by storing them on the
disk.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9318 6f19259b-4bc3-4df7-8a09-765794883524
This library provides an interface where variables can be saved and restored
using a file in a file system accessible to the firmware. It is expected
that a platform BDS library will use this library. The platform BDS
implementation can decide which devices to connect and then to attempt to use
for saving and restoring NV variables.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9272 6f19259b-4bc3-4df7-8a09-765794883524
jljusten
hhtian