Driver was supporting only 32b DMA support for V3 controllers. Add
support for 64b DMA as well for completeness.
For V4.0 64b support, driver was looking at incorrect capability
register bit. Fix for that is present as well.
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1583
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ashish Singhal <ashishsingha@nvidia.com>
Tested-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Add SDMA, ADMA2 and 26b data length support.
If V4 64 bit address mode is supported in capabilities register,
program controller to enable V4 host mode and use appropriate
SDMA registers supporting 64 bit addresses.
If V4 64 bit address mode is supported in capabilities register,
program controller to enable V4 host mode and use appropriate
ADMA descriptors supporting 64 bit addresses.
If host controller version is above V4.0, enable ADMA2 with 26b data
length support for better performance. HC 2 register is configured to
use 26 bit data lengths and ADMA2 descriptors are configured appropriately.
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1359
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ashish Singhal <ashishsingha@nvidia.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Some SdMmc host controllers are run by clocks with different
frequency than it is reflected in Capabilities Register 1.
It is allowed by SDHCI specification ver. 4.2 - if BaseClkFreq
field value of the Capability Register 1 is zero, the clock
frequency must be obtained via another method.
Because the bitfield is only 8 bits wide, a maximum value
that could be obtained from hardware is 255MHz.
In case the actual frequency exceeds 255MHz, the 8-bit BaseClkFreq
member of SD_MMC_HC_SLOT_CAP structure occurs to be not sufficient
to be used for setting the clock speed in SdMmcHcClockSupply
function.
This patch adds new UINT32 array ('BaseClkFreq[]') to
SD_MMC_HC_PRIVATE_DATA structure for specifying
the input clock speed for each slot of the host controller.
All routines that are used for clock configuration are
updated accordingly.
This patch also adds new IN OUT BaseClockFreq field
in the Capability callback of the SdMmcOverride,
protocol which allows to update BaseClkFreq value.
The patch reuses original commit from edk2-platforms:
20f6f144d3a8 ("Marvell/Drivers: XenonDxe: Allow overriding base clock
frequency")
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Invoke the newly introduced SD/MMC override protocol to override
the capabilities register after reading it from the device registers,
and to call the pre/post host init and reset hooks at the appropriate
times.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Check if the card is identified/initialized correctly. if not, break
the following cmd execution through PassThru()/ResetDevice().
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
This stack includes:
1. Dxe phase support by:
1) SdMmcPciHcDxe driver to consume PciIo and produce
SdMmcPassThru.
2) SdDxe driver to consume SdMmcPassThru to produce
BlkIo1/BlkIo2.
3) EmmcDxe driver to consume SdMmcPassThru to produce
BlkIo1/BlkIo2/SSP.
2. Pei phase support
1) SdBlockIoPei driver to consume SdMmcHostController
Ppi and produce VirutalBlkIo1&2.
2) EmmcBlockIoPei driver to consume SdMmcHostController
Ppi and produce VirutalBlkIo1&2.
3) SdMmcPciHcPei driver to produce SdMmcHostController
Ppi.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Michael D Kinney
Ashish Singhal
Marcin Wojtas
Ard Biesheuvel
Feng Tian