Remove this unused version: all existing platforms use the one under
ArmPlatformPkg instead.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Add a PCD to allow the platform to mask in/out specific features of
the LAN9118 device advertised during auto-negotiation.
For example, the Juno ARM Development Platform doesn't support full
duplex mode. This PCD will allow the platform developer to prevent the
full duplex modes from being advertised.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
[ardb: change default feature mask so that full duplex is disabled]
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
EmbeddedGpio only supports one gpio controller in one platform. Now
create PLATFORM_GPIO_CONTROLLER to support multiple gpio controllers
in one platform.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Add a PCD for the link negotiation timeout so the platform can over-ride
the default value.
The code previously did 2000 iterations of the loop with a 2us stall, so
the code has been changed subtly to set the number of iterations equal
to the PCD value divided by the stall time.
Since the stall time has not changed, the default PCD value is set at
4000 so the original behaviour is not changed.
The problems were discovered when the ARM Juno Development Platform used
the "EFI Network" option with then LAN9118 driver. It fails to boot the
first time and so the board drops back to Shell again:
Warning: LAN9118 Driver in stopped state
Link timeout in auto-negotiation.
Lan9118: Auto Negociation not supported.
EhcExecTransfer: transfer failed with 2
EhcControlTransfer: error - Device Error, transfer - 2
Buffer: EFI Hard Drive
Booting EFI Misc Device
Booting EFI Misc Device 1
Booting EFI Hard Drive
Booting EFI Network
Warning: LAN9118 Driver not initialized
Link timeout in auto-negotiation.
Lan9118: Auto Negociation not supported.
Booting EFI Internal Shell
Exiting Shell drops the user back to the Intel BDS UI. Selecting
"Continue" then succeeds in booting from the EFI Network:
Booting EFI Misc Device
Booting EFI Misc Device 1
Booting EFI Hard Drive
Booting EFI Network
..MnpFreeTxBuf: Duplicated recycle report from SNP.
MnpFreeTxBuf: Duplicated recycle report from SNP.
[snip repeated errors]
Discussion on the edk2-devel mailing list [1] prompted Laszlo Ersek to
suggest the time taken for the NIC to negotiate was causing a problem.
He suggested the solution contained in this patch to provide a PCD
configurable by the platform.
The default PCD value does not work for Juno. Setting the PCD to a
larger value works for Juno R0, R1 and R2.
[1] http://article.gmane.org/gmane.comp.bios.edk2.devel/7341
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Note: This is the same SATA controller present on Juno R1.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17413 6f19259b-4bc3-4df7-8a09-765794883524
This command dumps the Flat Device Tree currently installed
in the EFI Configuration Table.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17303 6f19259b-4bc3-4df7-8a09-765794883524
Instead of using a dynamic PCD, store the device tree address in a HOB
so that we can also run under a configuration that does not support
dynamic PCDs.
This also adds MemoryAllocationLib to the [LibraryClasses] section of
ArmVirtualizationPlatformLib/ArmVirtualizationPlatformLib.inf, as this
dependency was formerly satisfied transitively through one of the
library dependencies that were dropped.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16959 6f19259b-4bc3-4df7-8a09-765794883524
The FdtPlatformDxe driver installs the FDT of the platform it
is running on into the UEFI Configuration table at the end of
the DXE phase.
Please refer to the README.txt file for a global overview of
the driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <Ronald.Cron@arm.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16933 6f19259b-4bc3-4df7-8a09-765794883524
This driver doesn't support OTG - it simply sets the NXP ISP1761 in pure
peripheral mode.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15314 6f19259b-4bc3-4df7-8a09-765794883524
This change introduces default values for the PCDs PcdPrePiCpuMemorySize & PcdPrePiCpuIoSize.
These values are for the architectures ARM, AARCH64, IA32 and X64.
The redefinition of these PCDs (with the same default values) have been removed from the DSC files.
Note: the default value for AARCH64 was 32. It was preventing to allocate buffer above the 32bit
address space.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14914 6f19259b-4bc3-4df7-8a09-765794883524
The UEFI platform designer had to add '%a' to their EBL prompt PCD to print out the path
in the shell.
This change makes the addition of the path automatically after the platform specific value
in the EBL shell.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11798 6f19259b-4bc3-4df7-8a09-765794883524
ArmPkg - Supoprt for ARM specific things that can change as the architecture changes. Plus semihosting JTAG drivers.
EmbeddedPkg - Generic support for an embeddded platform. Including a light weight command line shell.
BeagleBoardPkg - Platform specifics for BeagleBoard. SD Card works, but USB has issues. Looks like a bug in the open source USB stack (Our internal stack works fine).
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9518 6f19259b-4bc3-4df7-8a09-765794883524
Ard Biesheuvel
Ryan Harkin
Haojian Zhuang
Olivier Martin
Ronald Cron
Brendan Jackman
oliviermartin
andrewfish
hhtian
AJFISH