Currently, we complete a synchronous operation without unmapping the
DMA mappings, and free the pages using FreePages () rather than calling
EFI_PCI_IO_PROTOCOL::FreeBuffer. This is simply incorrect, but it also
breaks non-coherent DMA as well as DMA protection and/or memory encryption
so let's do it correctly and call SdMmcFreeTrb() instead.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
At worst case, OCR register may always not set BIT31. It will cause
original code enter to dead loop. Adding a break for such case.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
If the code eventually returns "Status" anyway, it does not make
sense to explicitly return "Status" in case of an error, too.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The commit e27cca has a typo on DEBUG level macro. And this debug
message should be DEBUG_INFO rather than DEBUG_ERROR.
Cc: Jan Dabros <jsd@semihalf.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
reviewed-by: Marcin Wojtas <mw@semihalf.com>
EFI_D_INFO, EFI_D_VERBOSE, EFI_D_WARN and EFI_D_ERROR are replaced
with currently recommended values.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
We have to upgrade the TPL level used by SdMmc stack because the
following flow:
DiskIo2ReadWriteDisk() in logical partition -> PartitionReadBlocksEx()
in logical partition at TPL callback level -> ProbeMediaStatusEx()
with sync request -> DiskIo2ReadWriteDisk() in physical partition ->
waiting for async task completion.
if the low layer driver doesn't run at TPL_NOTIFY level, it will have
no time to trigger async task and cause system hang.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
This delay is necessary for eMMC reset to working properly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Joe Zhou <shjzhou@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Before switch to a bus mode, we need check if the SD device supports
this bus mode.
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
The original code is using ADMA mode to do clock tuning procedure. It
may have problem on some SD/MMC host controllers as there is no way to
know when to send next tuning cmd.
Update it to PIO mode to strictly follow SD Host Controller Simplified
Specification 3.0 Figure 2-29. By this way, if the Buffer Read Ready
interrupt is set, we could know it's ok to send the next clock tuning
cmd.
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
The original code has a bug to calculate which clock freq should be
used when the target clock freq is larger than the BaseClock Freq
provided by the system.
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Check if the card is identified/initialized correctly. if not, break
the following cmd execution through PassThru()/ResetDevice().
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
According to SD Host Controller 3.0 spec figure 3-10, we have to wait
1ms before checking DAT[3:0] in voltage switch proc
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
The original code doesn't reset the slot when there is device change.
It may bring issue on device identification procedure of some SD cards.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@Intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
If there is no card presented before power on, there would
have no card change interrupt generated. This is a corner
case which can't be handled by old logic.
The patch is used to move card present detection in the front
of card change interrupt detection.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
This stack includes:
1. Dxe phase support by:
1) SdMmcPciHcDxe driver to consume PciIo and produce
SdMmcPassThru.
2) SdDxe driver to consume SdMmcPassThru to produce
BlkIo1/BlkIo2.
3) EmmcDxe driver to consume SdMmcPassThru to produce
BlkIo1/BlkIo2/SSP.
2. Pei phase support
1) SdBlockIoPei driver to consume SdMmcHostController
Ppi and produce VirutalBlkIo1&2.
2) EmmcBlockIoPei driver to consume SdMmcHostController
Ppi and produce VirutalBlkIo1&2.
3) SdMmcPciHcPei driver to produce SdMmcHostController
Ppi.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Ard Biesheuvel
Feng Tian
Hao Wu
Thomas Huth
Joe Zhou