The comments describes the device as being 32-bit:
"the maximum time span is just over 136 years"
then uses a UINTN to hold the value.
Change to UINT32 so we don't get different behaviour for different architectures.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Use an untyped PCD reference for PcdSerialRegisterBase, so that the
library gets built without hardcoded values, permitting modules to
override the default serial port. This allows SerialDxe to use a
different serial port from the one used for DEBUG output (which
often gets occluded due to the console driver clearing the screen).
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The SP805 watchdog driver doesn't implement the PI watchdog protocol
fully, but always simply resets the system if the watchdog time runs
out.
However, the hardware does support the intended usage model, as long
as the SP805 is wired up correctly. So let's implement interrupt based
mode involving a handler that is registered by the DXE core and invoked
when the watchdog runs out. In the interrupt handler, we invoke the
notify function if one was registered, before calling the ResetSystem()
runtime service (as per the UEFI spec)
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Before fixing the SP805 driver, let's clean it up a bit. No
functional changes.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Limit the PEI memory region so it will not extend beyond what we can
address architecturally when running with 4 KB pages.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Drop some PCD references that are not actually referenced from the
PlatformPei code.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Derive the size of the GCD memory space map directly from the CPU's
information registers rather than from the PcdPrePiCpuMemorySize PCD,
which will be removed.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
We no longer use per-instance GUIDs to identify NOR flash banks so
there is no longer a need to define them. Drop the Guid member from
the NOR_FLASH_DESCRIPTION type.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Thomas Abraham <thomas.abraham@arm.com>
Currently, each flash bank controlled by ArmPlatformPkg/NorFlashDxe
has its own VendorHw GUID, and instances of NorFlashPlatformLib
describe each bank to the driver, along with the GUID for each.
This works ok for bare metal platforms, but it would be useful for
virtual platforms if we could obtain this information from a
device tree, which would require us to invent GUIDs on the fly,
given that the 'cfi-flash' binding does not include a GUID.
So instead, let's switch to a single GUID for all flash banks,
and update the driver's device path handling to include an index
to identify each bank uniquely.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Thomas Abraham <thomas.abraham@arm.com>
A subsequent patch will change the layout of devicepath nodes
produced by this driver. In preparation, make some tweaks to
the code to use a packed struct for the devicepath and to pass
the device index to NorFlashCreateInstance(). These are cosmetic
changes only, the resulting binaries should be identical.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Thomas Abraham <thomas.abraham@arm.com>
When setting up the stack in the startup code and jumping into C code
for the first time, ensure that the frame pointer register is cleared
so that backtraces terminate correctly. Otherwise, output like the
below is shown when encountering an exception on a DEBUG build:
Synchronous Exception at 0x0000000078A14780
PC 0x000078A14780 (0x000078A00000+0x00014780) [ 0] ArmVeNorFlashDxe.dll
PC 0x000078A10634 (0x000078A00000+0x00010634) [ 0] ArmVeNorFlashDxe.dll
PC 0x000078A11CF0 (0x000078A00000+0x00011CF0) [ 0] ArmVeNorFlashDxe.dll
PC 0x000078A11DD0 (0x000078A00000+0x00011DD0) [ 0] ArmVeNorFlashDxe.dll
PC 0x00007BC9D87C (0x00007BC98000+0x0000587C) [ 1] PartitionDxe.dll
PC 0x00007BC99B3C (0x00007BC98000+0x00001B3C) [ 1] PartitionDxe.dll
PC 0x00007F362F50 (0x00007F359000+0x00009F50) [ 2] DxeCore.dll
PC 0x00007BD63BB0 (0x00007BD5B000+0x00008BB0) [ 3] BdsDxe.dll
PC 0x00007BD6EE00 (0x00007BD5B000+0x00013E00) [ 3] BdsDxe.dll
PC 0x00007BD67C70 (0x00007BD5B000+0x0000CC70) [ 3] BdsDxe.dll
PC 0x00007F3724F0 (0x00007F359000+0x000194F0) [ 4] DxeCore.dll
PC 0x00004008FC30
PC 0x000040090130
PC 0x5800F6025800F5E1
Recursive exception occurred while dumping the CPU state
which is rather unhelpful, given that this prevent the remaining debug
output from being printed (register dump, stack dump, fault related
system registers etc)
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Removing rules for Ipf sources file:
* Remove the source file which path with "ipf" and also listed in
[Sources.IPF] section of INF file.
* Remove the source file which listed in [Components.IPF] section
of DSC file and not listed in any other [Components] section.
* Remove the embedded Ipf code for MDE_CPU_IPF.
Removing rules for Inf file:
* Remove IPF from VALID_ARCHITECTURES comments.
* Remove DXE_SAL_DRIVER from LIBRARY_CLASS in [Defines] section.
* Remove the INF which only listed in [Components.IPF] section in DSC.
* Remove statements from [BuildOptions] that provide IPF specific flags.
* Remove any IPF sepcific sections.
Removing rules for Dec file:
* Remove [Includes.IPF] section from Dec.
Removing rules for Dsc file:
* Remove IPF from SUPPORTED_ARCHITECTURES in [Defines] section of DSC.
* Remove any IPF specific sections.
* Remove statements from [BuildOptions] that provide IPF specific flags.
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Some platform support dynamic clocking, which is controlled by some
jumper setting or hardware registers. Result of that is that PCD
PL011UartClkInHz would need to be updated for frequency change.
This patch implements support for dynamic frequency for PL011 uart.
This patch implements default lib, which is using Pcd. Platform which
needs dynamic clocking needs implement PL011UartClockLib
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Udit Kumar <udit.kumar@nxp.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
This change adds support for the ARM Mali DP500/DP500/DP650 display
processors using the GOP protocol. It has been tested on FVP base
models + DP550 support. This change adds platform independant LcdHwLib
library. A corresponding platform specific library will be submitted
to edk-platforms/Platform/ARM/VExpressPkg.
This change does not modify functionality provided by PL111 or
HDLCD. This LcdHwLib implementation should be suitable for those
platforms that implement ARM Mali DP500/DP550/DP650 replacing
PL111/HDLCD.
Only graphics layer of the ARM Mali DP is configured for rendering
the RGB/BGR format frame buffer to satisfy the UEFI GOP requirements
Other layers e.g. video layers are not configured.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Currently framebuffer memory is either reserved in special VRAM or
dynamically allocated using boot services memory allocation functions.
When allocated using boot services calls the memory has to be allocated
as EfiBootServicesData. Unfortunately failures have been seen with this
case. There is also an unfortunate lack of control on the placement of
the framebuffer.
This change introduces two PCDs, PcdArmLcdFrameBufferBase and
PcdArmLcdFrameBufferSize which enable build time reservation of the
framebuffer, avoiding the need to allocate dynamically. This allows
the framebuffer to appear as "I/O memory" outside of the normal RAM
map, which is similar to the "VRAM" case.
This change has no impact on current code, only enables the option
of build time reservation of framebuffers.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Add definitions for new display modes such as HD 720.
This has no effect on existing display drivers.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This change adds a new PCD PcdArmHdlcdSwapBlueRedSelect
to swap values for HDLCD RED_SELECT and BLUE_SELECT registers
on platforms where blue and red hardware lines are swapped.
If set to TRUE in the platform dsc, HDLCD library will swap the values
while setting RED_SELECT and BLUE_SELECT registers. The default
value of the PCD is FALSE.
NOTE: The motive for this is that a discrepancy in the Red/Blue lines
exists between some VersatileExpress platforms. Rather than have
divergent code, this build switch allows a simple, pragmatic solution.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Current HDLCD and PL111 platform libraries do not support display modes
with PixelBlueGreenRedReserved8BitPerColor format, i.e. because of
historical confusion, they do not support the UEFI default
PixelBlueGreenRedReserved8BitPerColor format
In LcdPlatformLib for PL111, LcdPlatformQueryMode returns the pixel
format as PixelRedGreenBlueReserved8BitPerColor which is wrong, because
that does not match the display controller's pixel format which is set
to BGR in PL111Lcd LcdHwLib.
Also it is not possible to configure pixel format as RGB/BGR for the
display modes for a platform at build time.
This change adds PcdGopPixelFormat to configure pixel format as
PixelRedGreenBlueReserved8BitPerColor or
PixelBlueGreenRedReserved8BitPerColor or
PixelBitMask.
With this change, pixel format can be selected in the platform specific
.dsc file for all supported display modes.
Support for PixelBitMask is not implemented in PL111 or HDLCD LcdHwLib
libraries, hence HDLCD and PL111 platform libraries will return error
EFI_UNSUPPORTED if PcdGopPixelFormat is set to PixelBitMask. Indeed,
it is not clear what selecting PixelBitMask might mean, but the option
is allowed as it might suit a custom platform.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The LcdPlatformGetTimings interface function takes similar sets of
multiple parameters for horizontal and vertical timings which can be
aggregated in a common data type. This change defines a structure
SCAN_TIMINGS for this which can be used to describe both horizontal and
vertical scan timings, and accordingly redefines the
LcdPlatformGetTiming interface, greatly reducing the amount of data
passed about.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
LcdIdentify function does not currently check presence of HDLCD
controller.
Implement this functionality by reading HDLCD_REG_VERSION and checking
against the PRODUCT_ID field to detect presence of HDLCD controller.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Currenty bit LcdPwr of the LCDControl register is enabled immediately
after setting other bits of the LCDControl register. This two write
sequence is unnecessary. This change removes this extra write by setting
LcdPwr bit along with other bits of the LcdControl register.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
There is no functional modification in this change
some comments are modified and a few new comments are added.
This is to prevent mixing formatting changes with functional
changes.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
There is no functional modification in this change
As preparation for further work, the formatting is corrected to meet
the EDKII coding standard.
Of specific note, some invalid include guards were fixed.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This fix changes line endings of LcdPlatformNullLib.c to DOS
style line endings from UNIX style line endings to meet the EDK2
coding standard.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This fix changes line endings of LcdHwNullLib.c to DOS
style line endings from UNIX style line endings to meet the
EDK2 coding standard. Note it also fixes an end of line
whitespace.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The RealTimeClockLib class is declared under EmbeddedPkg, so that
platforms can provide the internals for the
EmbeddedPkg/RealTimeClockRuntimeDxe driver. In turn the driver produces
the Real Time Clock Arch Protocol, without which UEFI drivers cannot be
dispatched.
The PL031RealTimeClockLib instance calls gDS->SetMemorySpaceAttributes()
in the LibRtcInitialize() public function. This DXE service depends on the
CPU Arch Protocol. Add it to the depex.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Supreeth Venkatesh <Supreeth.Venkatesh@arm.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
NorFlashFvbInitialize() calls gDS->SetMemorySpaceAttributes() to mark the
varstore flash region as uncached. This DXE service depends on the CPU
Architectural protocol, and the DXE core is allowed to return
EFI_NOT_AVAILABLE_YET if it hasn't dispatched ArmPkg/Drivers/CpuDxe
earlier. Make the dependency explicit.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Supreeth Venkatesh <Supreeth.Venkatesh@arm.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The BEFORE depex opcode that we currently use to force ourselves in front
of the variable driver cannot be combined with other depex opcodes.
Replace the depex with TRUE, and signal NvVarStoreFormattedLib through the
installation of "gEdkiiNvVarStoreFormattedGuid".
Platforms that rely on NorFlashDxe to format the variable store (as
opposed to formatting a variable store template through an FDF file, as
part of the build) should hook NvVarStoreFormattedLib into the variable
drivers they use, so that the latter await our cue.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Supreeth Venkatesh <Supreeth.Venkatesh@arm.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The lazy initialization of the varstore FVB makes no longer sense at this
point:
- "mNorFlashInstanceTemplate.Initialize" is NULL;
- in NorFlashCreateInstance(), we only set Instance->Initialize to
non-NULL -- namely NorFlashFvbInitialize() -- if the FVB stands for the
variable store (see "ContainVariableStorage" / "SupportFvb");
- we call Instance->Initialize() from three places:
- from NorFlashWriteSingleBlock(), which is too late for the variable
read service ("variable write" depends on "variable read");
- from InitializeFvAndVariableStoreHeaders(), but that is only reachable
from NorFlashFvbInitialize(), i.e. recursively from
Instance->Initialize() itself;
- and from FvbRead(), which is never called by the variable driver, only
by the FTW driver. However, the variable driver may read (not write)
the memory-mapped varstore flash chip before the FTW driver is
dispatched.
Therefore the lazy initialization is both superfluous and insufficient.
Initialize the varstore headers eagerly, before we install the FVB
protocol interface.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Supreeth Venkatesh <Supreeth.Venkatesh@arm.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Instead of completely removing the memory occupied by the primary PrePi
FV from the memory map, thereby making it inaccessible to the OS, mark
it as boot services data. This will ensure that the memory is left
untouched by the firmware, but will release it to the OS when it calls
ExitBootServices().
Note that for reasons that are not entirely clear, this only works as
desired if the memory allocation HOB and the resource descriptor HOB
that describe the region are identical in offset and size, and so we
still need to iterate over the descriptors and split them up.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Commit 8ae5fc1829 ("ArmPlatformPkg/MemoryInitPeiLib: don't reserve
primary FV in memory") deleted the code that removes the memory covering
the primary firmware volume from the memory map. The assumption was that
this is no longer necessary now that we no longer expose compression and
PE/COFF loader library code from the PrePi module to DXE core.
However, the FV is still declared, and so code may attempt to access it
anyway, which may cause unexpected results depending on whether the
memory has been reused for other purposes in the mean time. So revert
this change in preparation of dealing with this in a better way.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Retire a whole bunch of ArmPlatformPkg PCDs that are either related
to the ARM BDS, to secure world execution or to stuff that has been
migrated to edk2-platforms.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Now that LcdGraphicsOutputDxe has been refactored, remove the old code
that is no longer used.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Create a new LcdGraphicsOutputDxe driver from the existing sources that
takes its hardware abstractions from a LcdHwLib library instance rather
than from a .c file linked directly. All we need is a new .inf file, and
a minimal tweak to LcdGraphicsOutputDxe.h to reuse the LcdHwlib prototypes
rather than open code them.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
[ardb: add it to ArmPlatformPkg.dsc so we can build test it standalone]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Convert the HdLcd specific code of LcdGraphicsOutputDxe into a LcdHwlib
implementation that we will wire up later into LcdGraphicsOutputDxe.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Convert the PL111 specific code of LcdGraphicsOutputDxe into a LcdHwlib
implementation that we will wire up later into LcdGraphicsOutputDxe.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Add the declaration and include file for the new LcdHwLib library class,
which will allow us to abstract away from platform variations in the
LCD graphics output driver.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
[ardb: add NULL implementation as well and add it to ArmPlatformPkg.dsc]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Use LcdPlatformLib not LcdPlatformNullLib (which is the name of this
instance) as LIBRARY_CLASS attribute.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Now that we have removed all the cruft from ArmPlatformPkg, add a .DSC
file that builds all the remaining components standalone, i.e., outside
of the context of any particular platform. This is primarily intended
for build time testing.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
In order to be able to build ArmPlatformPkg components outside of
the context of a particular platform, add Null implementation of
NorFlashPlatformLib.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
In order to be able to build ArmPlatformPkg components outside of
the context of a particular platform, add Null implementation of
LcdPlatformlLib.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
PrePeiCoreMPCore reuses the GUID of its unicore sibling, which is
usually fine, given that platforms never include both. However, it
prevents us from creating a package .DSC that does include both, so
update the GUID to a fresh one.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
ArmPlatformLibNullSec is built from a secondary .inf that omits
ArmPlatformLibNullMem.c from the [Sources] section so the library
can be used in a SEC context. This is slightly dodgy, given that
the resulting library is incomplete. Let's just remove this version,
since it isn't used anywhere anyway.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
None of the platforms we support use these so remove them.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This driver is no longer used anywhere so remove it.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Leif Lindholm
Michael D Kinney
Ard Biesheuvel
chenc2
Udit Kumar
Girish Pathak
Girish Pathak
Laszlo Ersek