/** @file
Definition of FDC registers and structures.

Copyright (c) 2006 - 2018, Intel Corporation. All rights reserved.<BR>

SPDX-License-Identifier: BSD-2-Clause-Patent

**/

#ifndef _PEI_RECOVERY_FDC_H_
#define _PEI_RECOVERY_FDC_H_

//
// FDC Registers
//
#define FDC_REGISTER_DOR  2 //Digital Output Register
#define FDC_REGISTER_MSR  4 //Main Status Register
#define FDC_REGISTER_DTR  5 //Data Register
#define FDC_REGISTER_CCR  7 //Configuration Control Register(data rate select)
#define FDC_REGISTER_DIR  7 //Digital Input Register(diskchange)
//
// FDC Register Bit Definitions
//
//
// Digital Out Register(WO)
//
#define SELECT_DRV      BIT0  // Select Drive: 0=A 1=B
#define RESET_FDC       BIT2  // Reset FDC
#define INT_DMA_ENABLE  BIT3  // Enable Int & DMA
#define DRVA_MOTOR_ON   BIT4  // Turn On Drive A Motor
#define DRVB_MOTOR_ON   BIT5  // Turn On Drive B Motor
//
// Main Status Register(RO)
//
#define MSR_DAB BIT0  // Drive A Busy
#define MSR_DBB BIT1  // Drive B Busy
#define MSR_CB  BIT4  // FDC Busy
#define MSR_NDM BIT5  // Non-DMA Mode
#define MSR_DIO BIT6  // Data Input/Output
#define MSR_RQM BIT7  // Request For Master
//
// Configuration Control Register(WO)
//
#define CCR_DRC (BIT0 | BIT1) // Data Rate select
//
// Digital Input Register(RO)
//
#define DIR_DCL     BIT7  // Disk change line
#define DRC_500KBS  0x0   // 500K
#define DRC_300KBS  0x01  // 300K
#define DRC_250KBS  0x02  // 250K
//
// FDC Command Code
//
#define READ_DATA_CMD         0x06
#define SEEK_CMD              0x0F
#define RECALIBRATE_CMD       0x07
#define SENSE_INT_STATUS_CMD  0x08
#define SPECIFY_CMD           0x03
#define SENSE_DRV_STATUS_CMD  0x04

///
/// CMD_MT: Multi_Track Selector
/// when set , this flag selects the multi-track operating mode.
/// In this mode, the FDC treats a complete cylinder under head0 and 1 as a single track
///
#define CMD_MT  BIT7

///
/// CMD_MFM: MFM/FM Mode Selector
/// A one selects the double density(MFM) mode
/// A zero selects single density (FM) mode
///
#define CMD_MFM BIT6

///
/// CMD_SK: Skip Flag
/// When set to 1, sectors containing a deleted data address mark will automatically be skipped
/// during the execution of Read Data.
/// When set to 0, the sector is read or written the same as the read and write commands.
///
#define CMD_SK  BIT5

//
// FDC Status Register Bit Definitions
//
//
// Status Register 0
//
#define STS0_IC (BIT7 | BIT6) // Interrupt Code
#define STS0_SE BIT5          // Seek End: the FDC completed a seek or recalibrate command
#define STS0_EC BIT4          // Equipment Check
#define STS0_NR BIT3          // Not Ready(unused), this bit is always 0
#define STS0_HA BIT2          // Head Address: the current head address
//
// STS0_US1 & STS0_US0: Drive Select(the current selected drive)
//
#define STS0_US1  BIT1  // Unit Select1
#define STS0_US0  BIT0  // Unit Select0
//
// Status Register 1
//
#define STS1_EN BIT7  // End of Cylinder
//
// BIT6 is unused
//
#define STS1_DE BIT5  // Data Error: The FDC detected a CRC error in either the ID field or data field of a sector
#define STS1_OR BIT4  // Overrun/Underrun: Becomes set if FDC does not receive CPU or DMA service within the required time interval
//
// BIT3 is unused
//
#define STS1_ND BIT2  // No data
#define STS1_NW BIT1  // Not Writable
#define STS1_MA BIT0  // Missing Address Mark

//
// Status Register 2
//
// BIT7 is unused
//
#define STS2_CM BIT6  // Control Mark
#define STS2_DD BIT5  // Data Error in Data Field: The FDC detected a CRC error in the data field
#define STS2_WC BIT4  // Wrong Cylinder: The track address from sector ID field is different from the track address maintained inside FDC
//
// BIT3 is unused
// BIT2 is unused
//
#define STS2_BC BIT1  // Bad Cylinder
#define STS2_MD BIT0  // Missing Address Mark in DataField

//
// Status Register 3
//
// BIT7 is unused
//
#define STS3_WP BIT6  // Write Protected
//
// BIT5 is unused
//
#define STS3_T0 BIT4  // Track 0
//
// BIT3 is unused
//
#define STS3_HD BIT2  // Head Address
//
// STS3_US1 & STS3_US0 : Drive Select
//
#define STS3_US1  BIT1  // Unit Select1
#define STS3_US0  BIT0  // Unit Select0

//
// Status Register 0 Interrupt Code Description
//
#define IC_NT   0x0   // Normal Termination of Command
#define IC_AT   0x40  // Abnormal Termination of Command
#define IC_IC   0x80  // Invalid Command
#define IC_ATRC 0xC0  // Abnormal Termination caused by Polling

///
/// Table of parameters for diskette
///
typedef struct {
  UINT8 EndOfTrack;          ///< End of track
  UINT8 GapLength;           ///< Gap length
  UINT8 DataLength;          ///< Data length
  UINT8 Number;              ///< Number of bytes per sector
  UINT8 MaxTrackNum;
  UINT8 MotorStartTime;
  UINT8 MotorOffTime;
  UINT8 HeadSettlingTime;
  UINT8 DataTransferRate;
} DISKET_PARA_TABLE;

///
/// Structure for FDC Command Packet 1
///
typedef struct {
  UINT8 CommandCode;
  UINT8 DiskHeadSel;
  UINT8 Cylinder;
  UINT8 Head;
  UINT8 Sector;
  UINT8 Number;
  UINT8 EndOfTrack;
  UINT8 GapLength;
  UINT8 DataLength;
} FDC_COMMAND_PACKET1;

///
/// Structure for FDC Command Packet 2
///
typedef struct {
  UINT8 CommandCode;
  UINT8 DiskHeadSel;
} FDC_COMMAND_PACKET2;

///
/// Structure for FDC Specify Command
///
typedef struct {
  UINT8 CommandCode;
  UINT8 SrtHut;
  UINT8 HltNd;
} FDC_SPECIFY_CMD;

///
/// Structure for FDC Seek Command
///
typedef struct {
  UINT8 CommandCode;
  UINT8 DiskHeadSel;
  UINT8 NewCylinder;
} FDC_SEEK_CMD;

///
/// Structure for FDC Result Packet
///
typedef struct {
  UINT8 Status0;
  UINT8 Status1;
  UINT8 Status2;
  UINT8 CylinderNumber;
  UINT8 HeaderAddress;
  UINT8 Record;
  UINT8 Number;
} FDC_RESULT_PACKET;

#endif