mirror of https://github.com/acidanthera/audk.git
483 lines
12 KiB
C
483 lines
12 KiB
C
/** @file
|
|
UART Serial Port library functions
|
|
|
|
Copyright (c) 2006 - 2018, Intel Corporation. All rights reserved.<BR>
|
|
SPDX-License-Identifier: BSD-2-Clause-Patent
|
|
|
|
**/
|
|
|
|
#include <Base.h>
|
|
#include <Library/IoLib.h>
|
|
#include <Library/SerialPortLib.h>
|
|
|
|
// ---------------------------------------------
|
|
// UART Register Offsets
|
|
// ---------------------------------------------
|
|
#define BAUD_LOW_OFFSET 0x00
|
|
#define BAUD_HIGH_OFFSET 0x01
|
|
#define IER_OFFSET 0x01
|
|
#define LCR_SHADOW_OFFSET 0x01
|
|
#define FCR_SHADOW_OFFSET 0x02
|
|
#define IR_CONTROL_OFFSET 0x02
|
|
#define FCR_OFFSET 0x02
|
|
#define EIR_OFFSET 0x02
|
|
#define BSR_OFFSET 0x03
|
|
#define LCR_OFFSET 0x03
|
|
#define MCR_OFFSET 0x04
|
|
#define LSR_OFFSET 0x05
|
|
#define MSR_OFFSET 0x06
|
|
|
|
// ---------------------------------------------
|
|
// UART Register Bit Defines
|
|
// ---------------------------------------------
|
|
#define LSR_TXRDY 0x20
|
|
#define LSR_RXDA 0x01
|
|
#define DLAB 0x01
|
|
#define MCR_DTRC 0x01
|
|
#define MCR_RTS 0x02
|
|
#define MSR_CTS 0x10
|
|
#define MSR_DSR 0x20
|
|
#define MSR_RI 0x40
|
|
#define MSR_DCD 0x80
|
|
|
|
// ---------------------------------------------
|
|
// UART Settings
|
|
// ---------------------------------------------
|
|
UINT16 gUartBase = 0x3F8;
|
|
UINTN gBps = 115200;
|
|
UINT8 gData = 8;
|
|
UINT8 gStop = 1;
|
|
UINT8 gParity = 0;
|
|
UINT8 gBreakSet = 0;
|
|
|
|
/**
|
|
Initialize the serial device hardware.
|
|
|
|
If no initialization is required, then return RETURN_SUCCESS.
|
|
If the serial device was successfully initialized, then return RETURN_SUCCESS.
|
|
If the serial device could not be initialized, then return RETURN_DEVICE_ERROR.
|
|
|
|
@retval RETURN_SUCCESS The serial device was initialized.
|
|
@retval RETURN_DEVICE_ERROR The serial device could not be initialized.
|
|
|
|
**/
|
|
RETURN_STATUS
|
|
EFIAPI
|
|
SerialPortInitialize (
|
|
VOID
|
|
)
|
|
{
|
|
UINTN Divisor;
|
|
UINT8 OutputData;
|
|
UINT8 Data;
|
|
|
|
//
|
|
// Map 5..8 to 0..3
|
|
//
|
|
Data = (UINT8)(gData - (UINT8)5);
|
|
|
|
//
|
|
// Calculate divisor for baud generator
|
|
//
|
|
Divisor = 115200 / gBps;
|
|
|
|
//
|
|
// Set communications format
|
|
//
|
|
OutputData = (UINT8)((DLAB << 7) | (gBreakSet << 6) | (gParity << 3) | (gStop << 2) | Data);
|
|
IoWrite8 (gUartBase + LCR_OFFSET, OutputData);
|
|
|
|
//
|
|
// Configure baud rate
|
|
//
|
|
IoWrite8 (gUartBase + BAUD_HIGH_OFFSET, (UINT8)(Divisor >> 8));
|
|
IoWrite8 (gUartBase + BAUD_LOW_OFFSET, (UINT8)(Divisor & 0xff));
|
|
|
|
//
|
|
// Switch back to bank 0
|
|
//
|
|
OutputData = (UINT8)((gBreakSet << 6) | (gParity << 3) | (gStop << 2) | Data);
|
|
IoWrite8 (gUartBase + LCR_OFFSET, OutputData);
|
|
|
|
return RETURN_SUCCESS;
|
|
}
|
|
|
|
/**
|
|
Write data from buffer to serial device.
|
|
|
|
Writes NumberOfBytes data bytes from Buffer to the serial device.
|
|
The number of bytes actually written to the serial device is returned.
|
|
If the return value is less than NumberOfBytes, then the write operation failed.
|
|
|
|
If Buffer is NULL, then ASSERT().
|
|
|
|
If NumberOfBytes is zero, then return 0.
|
|
|
|
@param Buffer Pointer to the data buffer to be written.
|
|
@param NumberOfBytes Number of bytes to written to the serial device.
|
|
|
|
@retval 0 NumberOfBytes is 0.
|
|
@retval >0 The number of bytes written to the serial device.
|
|
If this value is less than NumberOfBytes, then the write operation failed.
|
|
|
|
**/
|
|
UINTN
|
|
EFIAPI
|
|
SerialPortWrite (
|
|
IN UINT8 *Buffer,
|
|
IN UINTN NumberOfBytes
|
|
)
|
|
{
|
|
UINTN Result;
|
|
UINT8 Data;
|
|
|
|
if (Buffer == NULL) {
|
|
return 0;
|
|
}
|
|
|
|
Result = NumberOfBytes;
|
|
|
|
while ((NumberOfBytes--) != 0) {
|
|
//
|
|
// Wait for the serial port to be ready.
|
|
//
|
|
do {
|
|
Data = IoRead8 ((UINT16)gUartBase + LSR_OFFSET);
|
|
} while ((Data & LSR_TXRDY) == 0);
|
|
|
|
IoWrite8 ((UINT16)gUartBase, *Buffer++);
|
|
}
|
|
|
|
return Result;
|
|
}
|
|
|
|
/**
|
|
Reads data from a serial device into a buffer.
|
|
|
|
@param Buffer Pointer to the data buffer to store the data read from the serial device.
|
|
@param NumberOfBytes Number of bytes to read from the serial device.
|
|
|
|
@retval 0 NumberOfBytes is 0.
|
|
@retval >0 The number of bytes read from the serial device.
|
|
If this value is less than NumberOfBytes, then the read operation failed.
|
|
|
|
**/
|
|
UINTN
|
|
EFIAPI
|
|
SerialPortRead (
|
|
OUT UINT8 *Buffer,
|
|
IN UINTN NumberOfBytes
|
|
)
|
|
{
|
|
UINTN Result;
|
|
UINT8 Data;
|
|
|
|
if (NULL == Buffer) {
|
|
return 0;
|
|
}
|
|
|
|
Result = NumberOfBytes;
|
|
|
|
while ((NumberOfBytes--) != 0) {
|
|
//
|
|
// Wait for the serial port to be ready.
|
|
//
|
|
do {
|
|
Data = IoRead8 ((UINT16)gUartBase + LSR_OFFSET);
|
|
} while ((Data & LSR_RXDA) == 0);
|
|
|
|
*Buffer++ = IoRead8 ((UINT16)gUartBase);
|
|
}
|
|
|
|
return Result;
|
|
}
|
|
|
|
/**
|
|
Polls a serial device to see if there is any data waiting to be read.
|
|
|
|
Polls a serial device to see if there is any data waiting to be read.
|
|
If there is data waiting to be read from the serial device, then TRUE is returned.
|
|
If there is no data waiting to be read from the serial device, then FALSE is returned.
|
|
|
|
@retval TRUE Data is waiting to be read from the serial device.
|
|
@retval FALSE There is no data waiting to be read from the serial device.
|
|
|
|
**/
|
|
BOOLEAN
|
|
EFIAPI
|
|
SerialPortPoll (
|
|
VOID
|
|
)
|
|
{
|
|
UINT8 Data;
|
|
|
|
//
|
|
// Read the serial port status.
|
|
//
|
|
Data = IoRead8 ((UINT16)gUartBase + LSR_OFFSET);
|
|
|
|
return (BOOLEAN)((Data & LSR_RXDA) != 0);
|
|
}
|
|
|
|
/**
|
|
Sets the control bits on a serial device.
|
|
|
|
@param Control Sets the bits of Control that are settable.
|
|
|
|
@retval RETURN_SUCCESS The new control bits were set on the serial device.
|
|
@retval RETURN_UNSUPPORTED The serial device does not support this operation.
|
|
@retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
|
|
|
|
**/
|
|
RETURN_STATUS
|
|
EFIAPI
|
|
SerialPortSetControl (
|
|
IN UINT32 Control
|
|
)
|
|
{
|
|
UINT8 Mcr;
|
|
|
|
//
|
|
// First determine the parameter is invalid.
|
|
//
|
|
if ((Control & (~(EFI_SERIAL_REQUEST_TO_SEND | EFI_SERIAL_DATA_TERMINAL_READY))) != 0) {
|
|
return RETURN_UNSUPPORTED;
|
|
}
|
|
|
|
//
|
|
// Read the Modem Control Register.
|
|
//
|
|
Mcr = IoRead8 ((UINT16)gUartBase + MCR_OFFSET);
|
|
Mcr &= (~(MCR_DTRC | MCR_RTS));
|
|
|
|
if ((Control & EFI_SERIAL_DATA_TERMINAL_READY) == EFI_SERIAL_DATA_TERMINAL_READY) {
|
|
Mcr |= MCR_DTRC;
|
|
}
|
|
|
|
if ((Control & EFI_SERIAL_REQUEST_TO_SEND) == EFI_SERIAL_REQUEST_TO_SEND) {
|
|
Mcr |= MCR_RTS;
|
|
}
|
|
|
|
//
|
|
// Write the Modem Control Register.
|
|
//
|
|
IoWrite8 ((UINT16)gUartBase + MCR_OFFSET, Mcr);
|
|
|
|
return RETURN_SUCCESS;
|
|
}
|
|
|
|
/**
|
|
Retrieve the status of the control bits on a serial device.
|
|
|
|
@param Control A pointer to return the current control signals from the serial device.
|
|
|
|
@retval RETURN_SUCCESS The control bits were read from the serial device.
|
|
@retval RETURN_UNSUPPORTED The serial device does not support this operation.
|
|
@retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
|
|
|
|
**/
|
|
RETURN_STATUS
|
|
EFIAPI
|
|
SerialPortGetControl (
|
|
OUT UINT32 *Control
|
|
)
|
|
{
|
|
UINT8 Msr;
|
|
UINT8 Mcr;
|
|
UINT8 Lsr;
|
|
|
|
*Control = 0;
|
|
|
|
//
|
|
// Read the Modem Status Register.
|
|
//
|
|
Msr = IoRead8 ((UINT16)gUartBase + MSR_OFFSET);
|
|
|
|
if ((Msr & MSR_CTS) == MSR_CTS) {
|
|
*Control |= EFI_SERIAL_CLEAR_TO_SEND;
|
|
}
|
|
|
|
if ((Msr & MSR_DSR) == MSR_DSR) {
|
|
*Control |= EFI_SERIAL_DATA_SET_READY;
|
|
}
|
|
|
|
if ((Msr & MSR_RI) == MSR_RI) {
|
|
*Control |= EFI_SERIAL_RING_INDICATE;
|
|
}
|
|
|
|
if ((Msr & MSR_DCD) == MSR_DCD) {
|
|
*Control |= EFI_SERIAL_CARRIER_DETECT;
|
|
}
|
|
|
|
//
|
|
// Read the Modem Control Register.
|
|
//
|
|
Mcr = IoRead8 ((UINT16)gUartBase + MCR_OFFSET);
|
|
|
|
if ((Mcr & MCR_DTRC) == MCR_DTRC) {
|
|
*Control |= EFI_SERIAL_DATA_TERMINAL_READY;
|
|
}
|
|
|
|
if ((Mcr & MCR_RTS) == MCR_RTS) {
|
|
*Control |= EFI_SERIAL_REQUEST_TO_SEND;
|
|
}
|
|
|
|
//
|
|
// Read the Line Status Register.
|
|
//
|
|
Lsr = IoRead8 ((UINT16)gUartBase + LSR_OFFSET);
|
|
|
|
if ((Lsr & LSR_TXRDY) == LSR_TXRDY) {
|
|
*Control |= EFI_SERIAL_OUTPUT_BUFFER_EMPTY;
|
|
}
|
|
|
|
if ((Lsr & LSR_RXDA) == 0) {
|
|
*Control |= EFI_SERIAL_INPUT_BUFFER_EMPTY;
|
|
}
|
|
|
|
return RETURN_SUCCESS;
|
|
}
|
|
|
|
/**
|
|
Sets the baud rate, receive FIFO depth, transmit/receive time out, parity,
|
|
data bits, and stop bits on a serial device.
|
|
|
|
@param BaudRate The requested baud rate. A BaudRate value of 0 will use the
|
|
device's default interface speed.
|
|
On output, the value actually set.
|
|
@param ReceiveFifoDepth The requested depth of the FIFO on the receive side of the
|
|
serial interface. A ReceiveFifoDepth value of 0 will use
|
|
the device's default FIFO depth.
|
|
On output, the value actually set.
|
|
@param Timeout The requested time out for a single character in microseconds.
|
|
This timeout applies to both the transmit and receive side of the
|
|
interface. A Timeout value of 0 will use the device's default time
|
|
out value.
|
|
On output, the value actually set.
|
|
@param Parity The type of parity to use on this serial device. A Parity value of
|
|
DefaultParity will use the device's default parity value.
|
|
On output, the value actually set.
|
|
@param DataBits The number of data bits to use on the serial device. A DataBits
|
|
value of 0 will use the device's default data bit setting.
|
|
On output, the value actually set.
|
|
@param StopBits The number of stop bits to use on this serial device. A StopBits
|
|
value of DefaultStopBits will use the device's default number of
|
|
stop bits.
|
|
On output, the value actually set.
|
|
|
|
@retval RETURN_SUCCESS The new attributes were set on the serial device.
|
|
@retval RETURN_UNSUPPORTED The serial device does not support this operation.
|
|
@retval RETURN_INVALID_PARAMETER One or more of the attributes has an unsupported value.
|
|
@retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
|
|
|
|
**/
|
|
RETURN_STATUS
|
|
EFIAPI
|
|
SerialPortSetAttributes (
|
|
IN OUT UINT64 *BaudRate,
|
|
IN OUT UINT32 *ReceiveFifoDepth,
|
|
IN OUT UINT32 *Timeout,
|
|
IN OUT EFI_PARITY_TYPE *Parity,
|
|
IN OUT UINT8 *DataBits,
|
|
IN OUT EFI_STOP_BITS_TYPE *StopBits
|
|
)
|
|
{
|
|
UINTN Divisor;
|
|
UINT8 OutputData;
|
|
UINT8 LcrData;
|
|
UINT8 LcrParity;
|
|
UINT8 LcrStop;
|
|
|
|
//
|
|
// Check for default settings and fill in actual values.
|
|
//
|
|
if (*BaudRate == 0) {
|
|
*BaudRate = gBps;
|
|
}
|
|
|
|
if (*DataBits == 0) {
|
|
*DataBits = gData;
|
|
}
|
|
|
|
if (*Parity == DefaultParity) {
|
|
*Parity = NoParity;
|
|
}
|
|
|
|
if (*StopBits == DefaultStopBits) {
|
|
*StopBits = OneStopBit;
|
|
}
|
|
|
|
if ((*DataBits < 5) || (*DataBits > 8)) {
|
|
return RETURN_INVALID_PARAMETER;
|
|
}
|
|
|
|
//
|
|
// Map 5..8 to 0..3
|
|
//
|
|
LcrData = (UINT8)(*DataBits - (UINT8)5);
|
|
|
|
switch (*Parity) {
|
|
case NoParity:
|
|
LcrParity = 0;
|
|
break;
|
|
|
|
case EvenParity:
|
|
LcrParity = 3;
|
|
break;
|
|
|
|
case OddParity:
|
|
LcrParity = 1;
|
|
break;
|
|
|
|
case SpaceParity:
|
|
LcrParity = 7;
|
|
break;
|
|
|
|
case MarkParity:
|
|
LcrParity = 5;
|
|
break;
|
|
|
|
default:
|
|
return RETURN_INVALID_PARAMETER;
|
|
}
|
|
|
|
switch (*StopBits) {
|
|
case OneStopBit:
|
|
LcrStop = 0;
|
|
break;
|
|
|
|
case OneFiveStopBits:
|
|
case TwoStopBits:
|
|
LcrStop = 1;
|
|
break;
|
|
|
|
default:
|
|
return RETURN_INVALID_PARAMETER;
|
|
}
|
|
|
|
//
|
|
// Calculate divisor for baud generator
|
|
//
|
|
Divisor = 115200 / (UINTN)*BaudRate;
|
|
|
|
//
|
|
// Set communications format
|
|
//
|
|
OutputData = (UINT8)((DLAB << 7) | (gBreakSet << 6) | (LcrParity << 3) | (LcrStop << 2) | LcrData);
|
|
IoWrite8 (gUartBase + LCR_OFFSET, OutputData);
|
|
|
|
//
|
|
// Configure baud rate
|
|
//
|
|
IoWrite8 (gUartBase + BAUD_HIGH_OFFSET, (UINT8)(Divisor >> 8));
|
|
IoWrite8 (gUartBase + BAUD_LOW_OFFSET, (UINT8)(Divisor & 0xff));
|
|
|
|
//
|
|
// Switch back to bank 0
|
|
//
|
|
OutputData = (UINT8)((gBreakSet << 6) | (LcrParity << 3) | (LcrStop << 2) | LcrData);
|
|
IoWrite8 (gUartBase + LCR_OFFSET, OutputData);
|
|
|
|
return RETURN_SUCCESS;
|
|
}
|