mirror of https://github.com/acidanthera/audk.git
83 lines
4.5 KiB
Plaintext
83 lines
4.5 KiB
Plaintext
================================================================================
|
|
Build And Integration Instructions
|
|
2020 Aug 1st
|
|
================================================================================
|
|
|
|
================================================================================
|
|
DISCLAIMER
|
|
================================================================================
|
|
This release note as well as the software described in it is furnished under license
|
|
and may only be used or copied in accordance with the terms of the license. The
|
|
information in this manual is furnished for informational use only, is subject to
|
|
change without notice, and should not be construed as a commitment by Intel Corporation.
|
|
Intel Corporation assumes no responsibility or liability for any errors or inaccuracies
|
|
that may appear in this document or any software that may be provided in association
|
|
with this document.
|
|
Except as permitted by such license, no part of this document may be reproduced,
|
|
stored in a retrieval system, or transmitted in any form or by any means without
|
|
the express written consent of Intel Corporation.
|
|
|
|
================================================================================
|
|
INDEX
|
|
================================================================================
|
|
A. INTRODUCTION
|
|
B. HOW TO BUILD
|
|
C. HOW TO INTEGRATE INTO COREBOOT
|
|
D. HOW TO INTEGRATE INTO SLIM BOOTLOADER
|
|
|
|
================================================================================
|
|
A. INTRODUCTION
|
|
================================================================================
|
|
This document provides instructions on how to build UEFI Payload and how to
|
|
integrate it into coreboot or Slim Bootloader firmware.
|
|
|
|
================================================================================
|
|
B. HOW TO BUILD
|
|
================================================================================
|
|
1. Run the below two commands in windows command prompt window:
|
|
> edksetup.bat
|
|
|
|
For pure X64 build:
|
|
> build -a X64 -p UefiPayloadPkg\UefiPayloadPkg.dsc -b <BuildType> -t <ToolChain>
|
|
-D BOOTLOADER=<Bootloader>
|
|
|
|
For X64 build with IA32 entry point:
|
|
> build -a IA32 -a X64 -p UefiPayloadPkg\UefiPayloadPkg.dsc -b <BuildType> -t <ToolChain>
|
|
-D BOOTLOADER=<Bootloader>
|
|
|
|
<BuildType> support 'DEBUG', 'RELEASE' and 'NOOPT'.
|
|
<ToolChain> is the EDK II build environment on your host. Tested with VS2015x86 toolchain.
|
|
<Bootloader> could be "SBL" for Slim Bootloader and "COREBOOT" for coreboot.
|
|
|
|
Refer to https://github.com/tianocore/tianocore.github.io/wiki/UDK2018-How-to-Build for
|
|
details about EDK II build steps.
|
|
|
|
NOTE: Pure 32bit UEFI payload support could be added if required later.
|
|
|
|
2. If build is successfully, the payload image (UEFIPAYLOAD.fd) will be generated inside the
|
|
folder of Build\UefiPayloadPkg.
|
|
|
|
================================================================================
|
|
C. HOW TO INTEGRATE INTO COREBOOT
|
|
================================================================================
|
|
1. Copy the payload image (UEFIPAYLOAD.fd) into the top-level directory of Coreboot source tree.
|
|
2. Run "make menuconfig" in linux console to start Coreboot configuration surface.
|
|
3. In the Payload section,
|
|
1) Choose "Tianocore Payload" for the option of "Add a payload".
|
|
2) Update the path of payload image for the option of "Tianocore binary".
|
|
3) Choose "UEFIPayload" for the option of "Tianocore Payload".
|
|
4. If the graphics console is required in UEFI payload, enable framebuffer initialization in coreboot.
|
|
This could be done by enabling native graphics or using VGA BIOS option rom.
|
|
5. Build the coreboot firmware image.
|
|
6. If meet build error "E: Not a usable UEFI firmware volume.", please update Coreboot source tree
|
|
to the latest, or refer https://review.coreboot.org/c/coreboot/+/57296
|
|
|
|
================================================================================
|
|
D. HOW TO INTEGRATE INTO SLIM BOOTLOADER
|
|
================================================================================
|
|
Please refer https://slimbootloader.github.io/how-tos/integrate-multiple-payloads.html for below steps.
|
|
1. Copy the payload image (UEFIPAYLOAD.fd) into Slim Bootloader source at PayloadPkg\PayloadBins\UefiPld.fd
|
|
2. Update config data to make UEFI payload as default payload if required.
|
|
3. Build Slim Bootloader with UEFI payload:
|
|
BuildLoader.py build <Platform> -p "OsLoader.efi:LLDR:Lz4;UefiPld.fd:UEFI:Lzma"
|