mirror of https://github.com/acidanthera/audk.git
232 lines
8.5 KiB
C
232 lines
8.5 KiB
C
/** @file
|
|
*
|
|
* Copyright (c) 2011-2014, ARM Limited. All rights reserved.
|
|
*
|
|
* This program and the accompanying materials
|
|
* are licensed and made available under the terms and conditions of the BSD License
|
|
* which accompanies this distribution. The full text of the license may be found at
|
|
* http://opensource.org/licenses/bsd-license.php
|
|
*
|
|
* THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
|
|
* WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
|
|
*
|
|
**/
|
|
|
|
#ifndef __PL011_UART_H__
|
|
#define __PL011_UART_H__
|
|
|
|
#include <Uefi.h>
|
|
#include <Protocol/SerialIo.h>
|
|
|
|
// PL011 Registers
|
|
#define UARTDR 0x000
|
|
#define UARTRSR 0x004
|
|
#define UARTECR 0x004
|
|
#define UARTFR 0x018
|
|
#define UARTILPR 0x020
|
|
#define UARTIBRD 0x024
|
|
#define UARTFBRD 0x028
|
|
#define UARTLCR_H 0x02C
|
|
#define UARTCR 0x030
|
|
#define UARTIFLS 0x034
|
|
#define UARTIMSC 0x038
|
|
#define UARTRIS 0x03C
|
|
#define UARTMIS 0x040
|
|
#define UARTICR 0x044
|
|
#define UARTDMACR 0x048
|
|
|
|
#define UARTPID0 0xFE0
|
|
#define UARTPID1 0xFE4
|
|
#define UARTPID2 0xFE8
|
|
#define UARTPID3 0xFEC
|
|
|
|
// Data status bits
|
|
#define UART_DATA_ERROR_MASK 0x0F00
|
|
|
|
// Status reg bits
|
|
#define UART_STATUS_ERROR_MASK 0x0F
|
|
|
|
// Flag reg bits
|
|
#define PL011_UARTFR_RI (1 << 8) // Ring indicator
|
|
#define PL011_UARTFR_TXFE (1 << 7) // Transmit FIFO empty
|
|
#define PL011_UARTFR_RXFF (1 << 6) // Receive FIFO full
|
|
#define PL011_UARTFR_TXFF (1 << 5) // Transmit FIFO full
|
|
#define PL011_UARTFR_RXFE (1 << 4) // Receive FIFO empty
|
|
#define PL011_UARTFR_BUSY (1 << 3) // UART busy
|
|
#define PL011_UARTFR_DCD (1 << 2) // Data carrier detect
|
|
#define PL011_UARTFR_DSR (1 << 1) // Data set ready
|
|
#define PL011_UARTFR_CTS (1 << 0) // Clear to send
|
|
|
|
// Flag reg bits - alternative names
|
|
#define UART_TX_EMPTY_FLAG_MASK PL011_UARTFR_TXFE
|
|
#define UART_RX_FULL_FLAG_MASK PL011_UARTFR_RXFF
|
|
#define UART_TX_FULL_FLAG_MASK PL011_UARTFR_TXFF
|
|
#define UART_RX_EMPTY_FLAG_MASK PL011_UARTFR_RXFE
|
|
#define UART_BUSY_FLAG_MASK PL011_UARTFR_BUSY
|
|
|
|
// Control reg bits
|
|
#define PL011_UARTCR_CTSEN (1 << 15) // CTS hardware flow control enable
|
|
#define PL011_UARTCR_RTSEN (1 << 14) // RTS hardware flow control enable
|
|
#define PL011_UARTCR_RTS (1 << 11) // Request to send
|
|
#define PL011_UARTCR_DTR (1 << 10) // Data transmit ready.
|
|
#define PL011_UARTCR_RXE (1 << 9) // Receive enable
|
|
#define PL011_UARTCR_TXE (1 << 8) // Transmit enable
|
|
#define PL011_UARTCR_LBE (1 << 7) // Loopback enable
|
|
#define PL011_UARTCR_UARTEN (1 << 0) // UART Enable
|
|
|
|
// Line Control Register Bits
|
|
#define PL011_UARTLCR_H_SPS (1 << 7) // Stick parity select
|
|
#define PL011_UARTLCR_H_WLEN_8 (3 << 5)
|
|
#define PL011_UARTLCR_H_WLEN_7 (2 << 5)
|
|
#define PL011_UARTLCR_H_WLEN_6 (1 << 5)
|
|
#define PL011_UARTLCR_H_WLEN_5 (0 << 5)
|
|
#define PL011_UARTLCR_H_FEN (1 << 4) // FIFOs Enable
|
|
#define PL011_UARTLCR_H_STP2 (1 << 3) // Two stop bits select
|
|
#define PL011_UARTLCR_H_EPS (1 << 2) // Even parity select
|
|
#define PL011_UARTLCR_H_PEN (1 << 1) // Parity Enable
|
|
#define PL011_UARTLCR_H_BRK (1 << 0) // Send break
|
|
|
|
#define PL011_UARTPID2_VER(X) (((X) >> 4) & 0xF)
|
|
#define PL011_VER_R1P4 0x2
|
|
|
|
/*
|
|
|
|
Programmed hardware of Serial port.
|
|
|
|
@return Always return EFI_UNSUPPORTED.
|
|
|
|
**/
|
|
RETURN_STATUS
|
|
EFIAPI
|
|
PL011UartInitializePort (
|
|
IN OUT UINTN UartBase,
|
|
IN OUT UINT64 *BaudRate,
|
|
IN OUT UINT32 *ReceiveFifoDepth,
|
|
IN OUT EFI_PARITY_TYPE *Parity,
|
|
IN OUT UINT8 *DataBits,
|
|
IN OUT EFI_STOP_BITS_TYPE *StopBits
|
|
);
|
|
|
|
/**
|
|
|
|
Assert or deassert the control signals on a serial port.
|
|
The following control signals are set according their bit settings :
|
|
. Request to Send
|
|
. Data Terminal Ready
|
|
|
|
@param[in] UartBase UART registers base address
|
|
@param[in] Control The following bits are taken into account :
|
|
. EFI_SERIAL_REQUEST_TO_SEND : assert/deassert the
|
|
"Request To Send" control signal if this bit is
|
|
equal to one/zero.
|
|
. EFI_SERIAL_DATA_TERMINAL_READY : assert/deassert
|
|
the "Data Terminal Ready" control signal if this
|
|
bit is equal to one/zero.
|
|
. EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE : enable/disable
|
|
the hardware loopback if this bit is equal to
|
|
one/zero.
|
|
. EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE : not supported.
|
|
. EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE : enable/
|
|
disable the hardware flow control based on CTS (Clear
|
|
To Send) and RTS (Ready To Send) control signals.
|
|
|
|
@retval RETURN_SUCCESS The new control bits were set on the serial device.
|
|
@retval RETURN_UNSUPPORTED The serial device does not support this operation.
|
|
|
|
**/
|
|
RETURN_STATUS
|
|
EFIAPI
|
|
PL011UartSetControl (
|
|
IN UINTN UartBase,
|
|
IN UINT32 Control
|
|
);
|
|
|
|
/**
|
|
|
|
Retrieve the status of the control bits on a serial device.
|
|
|
|
@param[in] UartBase UART registers base address
|
|
@param[out] Control Status of the control bits on a serial device :
|
|
|
|
. EFI_SERIAL_DATA_CLEAR_TO_SEND, EFI_SERIAL_DATA_SET_READY,
|
|
EFI_SERIAL_RING_INDICATE, EFI_SERIAL_CARRIER_DETECT,
|
|
EFI_SERIAL_REQUEST_TO_SEND, EFI_SERIAL_DATA_TERMINAL_READY
|
|
are all related to the DTE (Data Terminal Equipment) and
|
|
DCE (Data Communication Equipment) modes of operation of
|
|
the serial device.
|
|
. EFI_SERIAL_INPUT_BUFFER_EMPTY : equal to one if the receive
|
|
buffer is empty, 0 otherwise.
|
|
. EFI_SERIAL_OUTPUT_BUFFER_EMPTY : equal to one if the transmit
|
|
buffer is empty, 0 otherwise.
|
|
. EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE : equal to one if the
|
|
hardware loopback is enabled (the ouput feeds the receive
|
|
buffer), 0 otherwise.
|
|
. EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE : equal to one if a
|
|
loopback is accomplished by software, 0 otherwise.
|
|
. EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE : equal to one if the
|
|
hardware flow control based on CTS (Clear To Send) and RTS
|
|
(Ready To Send) control signals is enabled, 0 otherwise.
|
|
|
|
|
|
@retval RETURN_SUCCESS The control bits were read from the serial device.
|
|
|
|
**/
|
|
RETURN_STATUS
|
|
EFIAPI
|
|
PL011UartGetControl (
|
|
IN UINTN UartBase,
|
|
OUT UINT32 *Control
|
|
);
|
|
|
|
/**
|
|
Write data to serial device.
|
|
|
|
@param Buffer Point of data buffer which need to be written.
|
|
@param NumberOfBytes Number of output bytes which are cached in Buffer.
|
|
|
|
@retval 0 Write data failed.
|
|
@retval !0 Actual number of bytes written to serial device.
|
|
|
|
**/
|
|
UINTN
|
|
EFIAPI
|
|
PL011UartWrite (
|
|
IN UINTN UartBase,
|
|
IN UINT8 *Buffer,
|
|
IN UINTN NumberOfBytes
|
|
);
|
|
|
|
/**
|
|
Read data from serial device and save the data in buffer.
|
|
|
|
@param Buffer Point of data buffer which need to be written.
|
|
@param NumberOfBytes Number of output bytes which are cached in Buffer.
|
|
|
|
@retval 0 Read data failed.
|
|
@retval !0 Actual number of bytes read from serial device.
|
|
|
|
**/
|
|
UINTN
|
|
EFIAPI
|
|
PL011UartRead (
|
|
IN UINTN UartBase,
|
|
OUT UINT8 *Buffer,
|
|
IN UINTN NumberOfBytes
|
|
);
|
|
|
|
/**
|
|
Check to see if any data is available to be read from the debug device.
|
|
|
|
@retval EFI_SUCCESS At least one byte of data is available to be read
|
|
@retval EFI_NOT_READY No data is available to be read
|
|
@retval EFI_DEVICE_ERROR The serial device is not functioning properly
|
|
|
|
**/
|
|
BOOLEAN
|
|
EFIAPI
|
|
PL011UartPoll (
|
|
IN UINTN UartBase
|
|
);
|
|
|
|
#endif
|