mirror of https://github.com/acidanthera/audk.git
269 lines
8.4 KiB
C
269 lines
8.4 KiB
C
/** @file
|
|
|
|
Copyright (c) 2007, Intel Corporation
|
|
All rights reserved. This program and the accompanying materials
|
|
are licensed and made available under the terms and conditions of the BSD License
|
|
which accompanies this distribution. The full text of the license may be found at
|
|
http://opensource.org/licenses/bsd-license.php
|
|
|
|
THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
|
|
WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
|
|
|
|
Module Name:
|
|
|
|
UsbMassBoot.h
|
|
|
|
Abstract:
|
|
|
|
The definition of command and data of the USB mass storage for
|
|
bootability command set.
|
|
|
|
Revision History
|
|
|
|
|
|
**/
|
|
|
|
#ifndef _EFI_USB_MASS_BOOT_H_
|
|
#define _EFI_USB_MASS_BOOT_H_
|
|
|
|
enum {
|
|
//
|
|
// The opcodes of various usb boot commands:
|
|
// INQUIRY/REQUEST_SENSE are "No Timeout Commands" as specified
|
|
// by MMC command set. Others are "Group 1 Timeout Commands". That
|
|
// is they should be retried if driver is ready.
|
|
// We can't use the Peripheral Device Type in Inquiry data to
|
|
// determine the timeout used. For example, both floppy and flash
|
|
// are likely set their PDT to 0, or Direct Access Device.
|
|
//
|
|
USB_BOOT_INQUIRY_OPCODE = 0x12,
|
|
USB_BOOT_REQUEST_SENSE_OPCODE = 0x03,
|
|
|
|
USB_BOOT_MODE_SENSE10_OPCODE = 0x5a,
|
|
USB_BOOT_READ_CAPACITY_OPCODE = 0x25,
|
|
USB_BOOT_TEST_UNIT_READY_OPCODE = 0x00,
|
|
USB_BOOT_READ10_OPCODE = 0x28,
|
|
USB_BOOT_WRITE10_OPCODE = 0x2a,
|
|
|
|
//
|
|
// The Sense Key part of the sense data. Sense data has three levels:
|
|
// Sense key, Additional Sense Code and Additional Sense Code Qualifier
|
|
//
|
|
USB_BOOT_SENSE_NO_SENSE = 0x00, // No sense key
|
|
USB_BOOT_SENSE_RECOVERED = 0x01, // Last command succeed with recovery actions
|
|
USB_BOOT_SENSE_NOT_READY = 0x02, // Device not ready
|
|
USB_BOOT_SNESE_MEDIUM_ERROR = 0X03, // Failed probably because flaw in the media
|
|
USB_BOOT_SENSE_HARDWARE_ERROR = 0X04, // Non-recoverable hardware failure
|
|
USB_BOOT_SENSE_ILLEGAL_REQUEST = 0X05, // Illegal parameters in the request
|
|
USB_BOOT_SENSE_UNIT_ATTENTION = 0X06, // Removable medium may have been changed
|
|
USB_BOOT_SNESE_DATA_PROTECT = 0X07, // Write protected
|
|
USB_BOOT_SENSE_BLANK_CHECK = 0X08, // Blank/non-blank medium while reading/writing
|
|
USB_BOOT_SENSE_VENDOR = 0X09, // Vendor specific sense key
|
|
USB_BOOT_SENSE_ABORTED = 0X0B, // Command aborted by the device
|
|
USB_BOOT_SENSE_VOLUME_OVERFLOW = 0x0D, // Partition overflow
|
|
USB_BOOT_SENSE_MISCOMPARE = 0x0E, // Source data mis-match while verfying.
|
|
|
|
USB_BOOT_ASC_NOT_READY = 0x04,
|
|
USB_BOOT_ASC_MEDIA_UPSIDE_DOWN = 0x06,
|
|
USB_BOOT_ASC_NO_MEDIA = 0x3A,
|
|
USB_BOOT_ASC_MEDIA_CHANGE = 0x28,
|
|
|
|
USB_BOOT_ASCQ_IN_PROGRESS = 0x01,
|
|
USB_BOOT_ASCQ_DEVICE_BUSY = 0xFF,
|
|
|
|
//
|
|
// Other parameters
|
|
//
|
|
USB_BOOT_IO_BLOCKS = 64,
|
|
|
|
//
|
|
// Boot Retry times
|
|
//
|
|
USB_BOOT_COMMAND_RETRY = 5,
|
|
USB_BOOT_WAIT_RETRY = 5,
|
|
|
|
//
|
|
// Boot Stall time
|
|
//
|
|
USB_BOOT_UNIT_READY_STALL = 50 * USB_MASS_STALL_1_MS,
|
|
|
|
//
|
|
// Boot Transfer timeout
|
|
//
|
|
USB_BOOT_GENERAL_BLOCK_TIMEOUT = 200 * USB_MASS_STALL_1_MS,
|
|
USB_BOOT_OPTICAL_BLOCK_TIMEOUT = 1 * USB_MASS_STALL_1_S,
|
|
USB_BOOT_GENERAL_CMD_TIMEOUT = 1 * USB_MASS_STALL_1_S,
|
|
USB_BOOT_INQUIRY_CMD_TIMEOUT = 3 * USB_MASS_STALL_1_S,
|
|
|
|
//
|
|
// Supported PDT codes, or Peripheral Device Type
|
|
//
|
|
USB_PDT_DIRECT_ACCESS = 0x00, // Direct access device
|
|
USB_PDT_CDROM = 0x05, // CDROM
|
|
USB_PDT_OPTICAL = 0x07, // Non-CD optical disks
|
|
USB_PDT_SIMPLE_DIRECT = 0x0E, // Simplified direct access device
|
|
};
|
|
|
|
//
|
|
// The required commands are INQUIRY, READ CAPACITY, TEST UNIT READY,
|
|
// READ10, WRITE10, and REQUEST SENSE. The BLOCK_IO protocol uses LBA
|
|
// so it isn't necessary to issue MODE SENSE / READ FORMAT CAPACITY
|
|
// command to retrieve the disk gemotrics.
|
|
//
|
|
#pragma pack(1)
|
|
typedef struct {
|
|
UINT8 OpCode;
|
|
UINT8 Lun; // Lun (high 3 bits)
|
|
UINT8 Reserved0[2];
|
|
UINT8 AllocLen;
|
|
UINT8 Reserved1;
|
|
UINT8 Pad[6];
|
|
} USB_BOOT_INQUIRY_CMD;
|
|
|
|
typedef struct {
|
|
UINT8 Pdt; // Peripheral Device Type (low 5 bits)
|
|
UINT8 Removable; // Removable Media (highest bit)
|
|
UINT8 Reserved0[2];
|
|
UINT8 AddLen; // Additional length
|
|
UINT8 Reserved1[3];
|
|
UINT8 VendorID[8];
|
|
UINT8 ProductID[16];
|
|
UINT8 ProductRevision[4];
|
|
} USB_BOOT_INQUIRY_DATA;
|
|
|
|
typedef struct {
|
|
UINT8 OpCode;
|
|
UINT8 Lun;
|
|
UINT8 Reserved0[8];
|
|
UINT8 Pad[2];
|
|
} USB_BOOT_READ_CAPACITY_CMD;
|
|
|
|
typedef struct {
|
|
UINT8 LastLba[4];
|
|
UINT8 BlockLen[4];
|
|
} USB_BOOT_READ_CAPACITY_DATA;
|
|
|
|
typedef struct {
|
|
UINT8 OpCode;
|
|
UINT8 Lun;
|
|
UINT8 Reserved[4];
|
|
UINT8 Pad[6];
|
|
} USB_BOOT_TEST_UNIT_READY_CMD;
|
|
|
|
typedef struct {
|
|
UINT8 OpCode;
|
|
UINT8 Lun;
|
|
UINT8 PageCode;
|
|
UINT8 Reserved0[4];
|
|
UINT8 ParaListLenMsb;
|
|
UINT8 ParaListLenLsb;
|
|
UINT8 Reserved1;
|
|
UINT8 Pad[2];
|
|
} USB_BOOT_MODE_SENSE_CMD;
|
|
|
|
typedef struct {
|
|
UINT8 ModeDataLenMsb;
|
|
UINT8 ModeDataLenLsb;
|
|
UINT8 Reserved0[4];
|
|
UINT8 BlkDesLenMsb;
|
|
UINT8 BlkDesLenLsb;
|
|
} USB_BOOT_MODE_PARA_HEADER;
|
|
|
|
typedef struct {
|
|
UINT8 OpCode;
|
|
UINT8 Lun; // Lun (High 3 bits)
|
|
UINT8 Lba[4]; // Logical block address
|
|
UINT8 Reserved0;
|
|
UINT8 TransferLen[2]; // Transfer length
|
|
UINT8 Reserverd1;
|
|
UINT8 Pad[2];
|
|
} USB_BOOT_READ10_CMD;
|
|
|
|
typedef struct {
|
|
UINT8 OpCode;
|
|
UINT8 Lun;
|
|
UINT8 Lba[4];
|
|
UINT8 Reserved0;
|
|
UINT8 TransferLen[2];
|
|
UINT8 Reserverd1;
|
|
UINT8 Pad[2];
|
|
} USB_BOOT_WRITE10_CMD;
|
|
|
|
typedef struct {
|
|
UINT8 OpCode;
|
|
UINT8 Lun; // Lun (High 3 bits)
|
|
UINT8 Reserved0[2];
|
|
UINT8 AllocLen; // Allocation length
|
|
UINT8 Reserved1;
|
|
UINT8 Pad[6];
|
|
} USB_BOOT_REQUEST_SENSE_CMD;
|
|
|
|
typedef struct {
|
|
UINT8 ErrorCode;
|
|
UINT8 Reserved0;
|
|
UINT8 SenseKey; // Sense key (low 4 bits)
|
|
UINT8 Infor[4];
|
|
UINT8 AddLen; // Additional Sense length, 10
|
|
UINT8 Reserved1[4];
|
|
UINT8 ASC; // Additional Sense Code
|
|
UINT8 ASCQ; // Additional Sense Code Qualifier
|
|
UINT8 Reserverd2[4];
|
|
} USB_BOOT_REQUEST_SENSE_DATA;
|
|
#pragma pack()
|
|
|
|
//
|
|
// Convert a LUN number to that in the command
|
|
//
|
|
#define USB_BOOT_LUN(Lun) ((Lun) << 5)
|
|
|
|
//
|
|
// Get the removable, PDT, and sense key bits from the command data
|
|
//
|
|
#define USB_BOOT_REMOVABLE(RmbByte) (((RmbByte) & 0x80) != 0)
|
|
#define USB_BOOT_PDT(Pdt) ((Pdt) & 0x1f)
|
|
#define USB_BOOT_SENSE_KEY(Key) ((Key) & 0x0f)
|
|
|
|
//
|
|
// Swap the byte sequence of a UINT32. Intel CPU uses little endian
|
|
// in UEFI environment, but USB boot uses big endian.
|
|
//
|
|
#define USB_BOOT_SWAP32(Data32) \
|
|
((((Data32) & 0x000000ff) << 24) | (((Data32) & 0xff000000) >> 24) | \
|
|
(((Data32) & 0x0000ff00) << 8) | (((Data32) & 0x00ff0000) >> 8))
|
|
|
|
#define USB_BOOT_SWAP16(Data16) \
|
|
((((Data16) & 0x00ff) << 8) | (((Data16) & 0xff00) >> 8))
|
|
|
|
EFI_STATUS
|
|
UsbBootGetParams (
|
|
IN USB_MASS_DEVICE *UsbMass
|
|
);
|
|
|
|
EFI_STATUS
|
|
UsbBootIsUnitReady (
|
|
IN USB_MASS_DEVICE *UsbMass
|
|
);
|
|
|
|
EFI_STATUS
|
|
UsbBootDetectMedia (
|
|
IN USB_MASS_DEVICE *UsbMass
|
|
);
|
|
|
|
EFI_STATUS
|
|
UsbBootReadBlocks (
|
|
IN USB_MASS_DEVICE *UsbMass,
|
|
IN UINT32 Lba,
|
|
IN UINTN TotalBlock,
|
|
OUT UINT8 *Buffer
|
|
);
|
|
|
|
EFI_STATUS
|
|
UsbBootWriteBlocks (
|
|
IN USB_MASS_DEVICE *UsbMass,
|
|
IN UINT32 Lba,
|
|
IN UINTN TotalBlock,
|
|
OUT UINT8 *Buffer
|
|
);
|
|
#endif
|
|
|