audk/MdeModulePkg/Bus/Pci/UhciDxe/UhciReg.h

249 lines
6.1 KiB
C

/** @file
The definition for UHCI register operation routines.
Copyright (c) 2007 - 2010, Intel Corporation
All rights reserved. This program and the accompanying materials
are licensed and made available under the terms and conditions of the BSD License
which accompanies this distribution. The full text of the license may be found at
http://opensource.org/licenses/bsd-license.php
THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
**/
#ifndef _EFI_UHCI_REG_H_
#define _EFI_UHCI_REG_H_
//
// UHCI register offset
//
#define UHCI_FRAME_NUM 1024
//
// Register offset and PCI related staff
//
#define USB_BAR_INDEX 4
#define USBCMD_OFFSET 0
#define USBSTS_OFFSET 2
#define USBINTR_OFFSET 4
#define USBPORTSC_OFFSET 0x10
#define USB_FRAME_NO_OFFSET 6
#define USB_FRAME_BASE_OFFSET 8
#define USB_EMULATION_OFFSET 0xC0
//
// Packet IDs
//
#define SETUP_PACKET_ID 0x2D
#define INPUT_PACKET_ID 0x69
#define OUTPUT_PACKET_ID 0xE1
#define ERROR_PACKET_ID 0x55
//
// USB port status and control bit definition.
//
#define USBPORTSC_CCS BIT0 // Current Connect Status
#define USBPORTSC_CSC BIT1 // Connect Status Change
#define USBPORTSC_PED BIT2 // Port Enable / Disable
#define USBPORTSC_PEDC BIT3 // Port Enable / Disable Change
#define USBPORTSC_LSL BIT4 // Line Status Low BIT
#define USBPORTSC_LSH BIT5 // Line Status High BIT
#define USBPORTSC_RD BIT6 // Resume Detect
#define USBPORTSC_LSDA BIT8 // Low Speed Device Attached
#define USBPORTSC_PR BIT9 // Port Reset
#define USBPORTSC_SUSP BIT12 // Suspend
//
// UHCI Spec said it must implement 2 ports each host at least,
// and if more, check whether the bit7 of PORTSC is always 1.
// So here assume the max of port number each host is 16.
//
#define USB_MAX_ROOTHUB_PORT 0x0F
//
// Command register bit definitions
//
#define USBCMD_RS BIT0 // Run/Stop
#define USBCMD_HCRESET BIT1 // Host reset
#define USBCMD_GRESET BIT2 // Global reset
#define USBCMD_EGSM BIT3 // Global Suspend Mode
#define USBCMD_FGR BIT4 // Force Global Resume
#define USBCMD_SWDBG BIT5 // SW Debug mode
#define USBCMD_CF BIT6 // Config Flag (sw only)
#define USBCMD_MAXP BIT7 // Max Packet (0 = 32, 1 = 64)
//
// USB Status register bit definitions
//
#define USBSTS_USBINT BIT0 // Interrupt due to IOC
#define USBSTS_ERROR BIT1 // Interrupt due to error
#define USBSTS_RD BIT2 // Resume Detect
#define USBSTS_HSE BIT3 // Host System Error
#define USBSTS_HCPE BIT4 // Host Controller Process Error
#define USBSTS_HCH BIT5 // HC Halted
#define USBTD_ACTIVE BIT7 // TD is still active
#define USBTD_STALLED BIT6 // TD is stalled
#define USBTD_BUFFERR BIT5 // Buffer underflow or overflow
#define USBTD_BABBLE BIT4 // Babble condition
#define USBTD_NAK BIT3 // NAK is received
#define USBTD_CRC BIT2 // CRC/Time out error
#define USBTD_BITSTUFF BIT1 // Bit stuff error
/**
Read a UHCI register.
@param PciIo The EFI_PCI_IO_PROTOCOL to use.
@param Offset Register offset to USB_BAR_INDEX.
@return Content of register.
**/
UINT16
UhciReadReg (
IN EFI_PCI_IO_PROTOCOL *PciIo,
IN UINT32 Offset
);
/**
Write data to UHCI register.
@param PciIo The EFI_PCI_IO_PROTOCOL to use.
@param Offset Register offset to USB_BAR_INDEX.
@param Data Data to write.
@return None.
**/
VOID
UhciWriteReg (
IN EFI_PCI_IO_PROTOCOL *PciIo,
IN UINT32 Offset,
IN UINT16 Data
);
/**
Set a bit of the UHCI Register.
@param PciIo The EFI_PCI_IO_PROTOCOL to use.
@param Offset Register offset to USB_BAR_INDEX.
@param Bit The bit to set.
@return None.
**/
VOID
UhciSetRegBit (
IN EFI_PCI_IO_PROTOCOL *PciIo,
IN UINT32 Offset,
IN UINT16 Bit
);
/**
Clear a bit of the UHCI Register.
@param PciIo The PCI_IO protocol to access the PCI.
@param Offset Register offset to USB_BAR_INDEX.
@param Bit The bit to clear.
@return None.
**/
VOID
UhciClearRegBit (
IN EFI_PCI_IO_PROTOCOL *PciIo,
IN UINT32 Offset,
IN UINT16 Bit
);
/**
Clear all the interrutp status bits, these bits
are Write-Clean.
@param Uhc The UHCI device.
@return None.
**/
VOID
UhciAckAllInterrupt (
IN USB_HC_DEV *Uhc
);
/**
Stop the host controller.
@param Uhc The UHCI device.
@param Timeout Max time allowed.
@retval EFI_SUCCESS The host controller is stopped.
@retval EFI_TIMEOUT Failed to stop the host controller.
**/
EFI_STATUS
UhciStopHc (
IN USB_HC_DEV *Uhc,
IN UINTN Timeout
);
/**
Check whether the host controller operates well.
@param PciIo The PCI_IO protocol to use.
@retval TRUE Host controller is working.
@retval FALSE Host controller is halted or system error.
**/
BOOLEAN
UhciIsHcWorking (
IN EFI_PCI_IO_PROTOCOL *PciIo
);
/**
Set the UHCI frame list base address. It can't use
UhciWriteReg which access memory in UINT16.
@param PciIo The EFI_PCI_IO_PROTOCOL to use.
@param Addr Address to set.
@return None.
**/
VOID
UhciSetFrameListBaseAddr (
IN EFI_PCI_IO_PROTOCOL *PciIo,
IN VOID *Addr
);
/**
Disable USB Emulation.
@param PciIo The EFI_PCI_IO_PROTOCOL protocol to use.
@return None.
**/
VOID
UhciTurnOffUsbEmulation (
IN EFI_PCI_IO_PROTOCOL *PciIo
);
#endif