mirror of https://github.com/acidanthera/audk.git
521 lines
28 KiB
C
521 lines
28 KiB
C
/** @file
|
|
EFI PCI I/O Protocol provides the basic Memory, I/O, PCI configuration,
|
|
and DMA interfaces that a driver uses to access its PCI controller.
|
|
|
|
Copyright (c) 2006 - 2008, Intel Corporation
|
|
All rights reserved. This program and the accompanying materials
|
|
are licensed and made available under the terms and conditions of the BSD License
|
|
which accompanies this distribution. The full text of the license may be found at
|
|
http://opensource.org/licenses/bsd-license.php
|
|
|
|
THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
|
|
WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
|
|
|
|
**/
|
|
|
|
#ifndef __PCI_IO_H__
|
|
#define __PCI_IO_H__
|
|
|
|
///
|
|
/// Global ID for the PCI I/O Protocol
|
|
///
|
|
#define EFI_PCI_IO_PROTOCOL_GUID \
|
|
{ \
|
|
0x4cf5b200, 0x68b8, 0x4ca5, {0x9e, 0xec, 0xb2, 0x3e, 0x3f, 0x50, 0x2, 0x9a } \
|
|
}
|
|
|
|
typedef struct _EFI_PCI_IO_PROTOCOL EFI_PCI_IO_PROTOCOL;
|
|
|
|
///
|
|
/// Prototypes for the PCI I/O Protocol
|
|
///
|
|
typedef enum {
|
|
EfiPciIoWidthUint8 = 0,
|
|
EfiPciIoWidthUint16,
|
|
EfiPciIoWidthUint32,
|
|
EfiPciIoWidthUint64,
|
|
EfiPciIoWidthFifoUint8,
|
|
EfiPciIoWidthFifoUint16,
|
|
EfiPciIoWidthFifoUint32,
|
|
EfiPciIoWidthFifoUint64,
|
|
EfiPciIoWidthFillUint8,
|
|
EfiPciIoWidthFillUint16,
|
|
EfiPciIoWidthFillUint32,
|
|
EfiPciIoWidthFillUint64,
|
|
EfiPciIoWidthMaximum
|
|
} EFI_PCI_IO_PROTOCOL_WIDTH;
|
|
|
|
//
|
|
// Complete PCI address generater
|
|
//
|
|
#define EFI_PCI_IO_PASS_THROUGH_BAR 0xff ///< Special BAR that passes a memory or I/O cycle through unchanged
|
|
#define EFI_PCI_IO_ATTRIBUTE_MASK 0x077f ///< All the following I/O and Memory cycles
|
|
#define EFI_PCI_IO_ATTRIBUTE_ISA_MOTHERBOARD_IO 0x0001 ///< I/O cycles 0x0000-0x00FF (10 bit decode)
|
|
#define EFI_PCI_IO_ATTRIBUTE_ISA_IO 0x0002 ///< I/O cycles 0x0100-0x03FF or greater (10 bit decode)
|
|
#define EFI_PCI_IO_ATTRIBUTE_VGA_PALETTE_IO 0x0004 ///< I/O cycles 0x3C6, 0x3C8, 0x3C9 (10 bit decode)
|
|
#define EFI_PCI_IO_ATTRIBUTE_VGA_MEMORY 0x0008 ///< MEM cycles 0xA0000-0xBFFFF (24 bit decode)
|
|
#define EFI_PCI_IO_ATTRIBUTE_VGA_IO 0x0010 ///< I/O cycles 0x3B0-0x3BB and 0x3C0-0x3DF (10 bit decode)
|
|
#define EFI_PCI_IO_ATTRIBUTE_IDE_PRIMARY_IO 0x0020 ///< I/O cycles 0x1F0-0x1F7, 0x3F6, 0x3F7 (10 bit decode)
|
|
#define EFI_PCI_IO_ATTRIBUTE_IDE_SECONDARY_IO 0x0040 ///< I/O cycles 0x170-0x177, 0x376, 0x377 (10 bit decode)
|
|
#define EFI_PCI_IO_ATTRIBUTE_MEMORY_WRITE_COMBINE 0x0080 ///< Map a memory range so write are combined
|
|
#define EFI_PCI_IO_ATTRIBUTE_IO 0x0100 ///< Enable the I/O decode bit in the PCI Config Header
|
|
#define EFI_PCI_IO_ATTRIBUTE_MEMORY 0x0200 ///< Enable the Memory decode bit in the PCI Config Header
|
|
#define EFI_PCI_IO_ATTRIBUTE_BUS_MASTER 0x0400 ///< Enable the DMA bit in the PCI Config Header
|
|
#define EFI_PCI_IO_ATTRIBUTE_MEMORY_CACHED 0x0800 ///< Map a memory range so all r/w accesses are cached
|
|
#define EFI_PCI_IO_ATTRIBUTE_MEMORY_DISABLE 0x1000 ///< Disable a memory range
|
|
#define EFI_PCI_IO_ATTRIBUTE_EMBEDDED_DEVICE 0x2000 ///< Clear for an add-in PCI Device
|
|
#define EFI_PCI_IO_ATTRIBUTE_EMBEDDED_ROM 0x4000 ///< Clear for a physical PCI Option ROM accessed through ROM BAR
|
|
#define EFI_PCI_IO_ATTRIBUTE_DUAL_ADDRESS_CYCLE 0x8000 ///< Clear for PCI controllers that can not genrate a DAC
|
|
#define EFI_PCI_IO_ATTRIBUTE_ISA_IO_16 0x10000 ///< I/O cycles 0x0100-0x03FF or greater (16 bit decode)
|
|
#define EFI_PCI_IO_ATTRIBUTE_VGA_PALETTE_IO_16 0x20000 ///< I/O cycles 0x3C6, 0x3C8, 0x3C9 (16 bit decode)
|
|
#define EFI_PCI_IO_ATTRIBUTE_VGA_IO_16 0x30000 ///< I/O cycles 0x3B0-0x3BB and 0x3C0-0x3DF (16 bit decode)
|
|
|
|
#define EFI_PCI_DEVICE_ENABLE (EFI_PCI_IO_ATTRIBUTE_IO | EFI_PCI_IO_ATTRIBUTE_MEMORY | EFI_PCI_IO_ATTRIBUTE_BUS_MASTER)
|
|
#define EFI_VGA_DEVICE_ENABLE (EFI_PCI_IO_ATTRIBUTE_VGA_PALETTE_IO | EFI_PCI_IO_ATTRIBUTE_VGA_MEMORY | EFI_PCI_IO_ATTRIBUTE_VGA_IO | EFI_PCI_IO_ATTRIBUTE_IO)
|
|
|
|
///
|
|
/// *******************************************************
|
|
/// EFI_PCI_IO_PROTOCOL_OPERATION
|
|
/// *******************************************************
|
|
///
|
|
typedef enum {
|
|
EfiPciIoOperationBusMasterRead,
|
|
EfiPciIoOperationBusMasterWrite,
|
|
EfiPciIoOperationBusMasterCommonBuffer,
|
|
EfiPciIoOperationMaximum
|
|
} EFI_PCI_IO_PROTOCOL_OPERATION;
|
|
|
|
///
|
|
/// *******************************************************
|
|
/// EFI_PCI_IO_PROTOCOL_ATTRIBUTE_OPERATION
|
|
/// *******************************************************
|
|
///
|
|
typedef enum {
|
|
EfiPciIoAttributeOperationGet,
|
|
EfiPciIoAttributeOperationSet,
|
|
EfiPciIoAttributeOperationEnable,
|
|
EfiPciIoAttributeOperationDisable,
|
|
EfiPciIoAttributeOperationSupported,
|
|
EfiPciIoAttributeOperationMaximum
|
|
} EFI_PCI_IO_PROTOCOL_ATTRIBUTE_OPERATION;
|
|
|
|
/**
|
|
Reads from the memory space of a PCI controller. Returns when either the polling exit criteria is
|
|
satisfied or after a defined duration.
|
|
|
|
@param This A pointer to the EFI_PCI_IO_PROTOCOL instance.
|
|
@param Width Signifies the width of the memory or I/O operations.
|
|
@param BarIndex The BAR index of the standard PCI Configuration header to use as the
|
|
base address for the memory operation to perform.
|
|
@param Offset The offset within the selected BAR to start the memory operation.
|
|
@param Mask Mask used for the polling criteria.
|
|
@param Value The comparison value used for the polling exit criteria.
|
|
@param Delay The number of 100 ns units to poll.
|
|
@param Result Pointer to the last value read from the memory location.
|
|
|
|
@retval EFI_SUCCESS The last data returned from the access matched the poll exit criteria.
|
|
@retval EFI_UNSUPPORTED BarIndex not valid for this PCI controller.
|
|
@retval EFI_UNSUPPORTED Offset is not valid for the BarIndex of this PCI controller.
|
|
@retval EFI_TIMEOUT Delay expired before a match occurred.
|
|
@retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources.
|
|
@retval EFI_INVALID_PARAMETER One or more parameters are invalid.
|
|
|
|
**/
|
|
typedef
|
|
EFI_STATUS
|
|
(EFIAPI *EFI_PCI_IO_PROTOCOL_POLL_IO_MEM)(
|
|
IN EFI_PCI_IO_PROTOCOL *This,
|
|
IN EFI_PCI_IO_PROTOCOL_WIDTH Width,
|
|
IN UINT8 BarIndex,
|
|
IN UINT64 Offset,
|
|
IN UINT64 Mask,
|
|
IN UINT64 Value,
|
|
IN UINT64 Delay,
|
|
OUT UINT64 *Result
|
|
);
|
|
|
|
/**
|
|
Enable a PCI driver to access PCI controller registers in the PCI memory or I/O space.
|
|
|
|
@param This A pointer to the EFI_PCI_IO_PROTOCOL instance.
|
|
@param Width Signifies the width of the memory or I/O operations.
|
|
@param BarIndex The BAR index of the standard PCI Configuration header to use as the
|
|
base address for the memory or I/O operation to perform.
|
|
@param Offset The offset within the selected BAR to start the memory or I/O operation.
|
|
@param Count The number of memory or I/O operations to perform.
|
|
@param Buffer For read operations, the destination buffer to store the results. For write
|
|
operations, the source buffer to write data from.
|
|
|
|
@retval EFI_SUCCESS The data was read from or written to the PCI controller.
|
|
@retval EFI_UNSUPPORTED BarIndex not valid for this PCI controller.
|
|
@retval EFI_UNSUPPORTED The address range specified by Offset, Width, and Count is not
|
|
valid for the PCI BAR specified by BarIndex.
|
|
@retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources.
|
|
@retval EFI_INVALID_PARAMETER One or more parameters are invalid.
|
|
|
|
**/
|
|
typedef
|
|
EFI_STATUS
|
|
(EFIAPI *EFI_PCI_IO_PROTOCOL_IO_MEM)(
|
|
IN EFI_PCI_IO_PROTOCOL *This,
|
|
IN EFI_PCI_IO_PROTOCOL_WIDTH Width,
|
|
IN UINT8 BarIndex,
|
|
IN UINT64 Offset,
|
|
IN UINTN Count,
|
|
IN OUT VOID *Buffer
|
|
);
|
|
|
|
typedef struct {
|
|
EFI_PCI_IO_PROTOCOL_IO_MEM Read;
|
|
EFI_PCI_IO_PROTOCOL_IO_MEM Write;
|
|
} EFI_PCI_IO_PROTOCOL_ACCESS;
|
|
|
|
/**
|
|
Enable a PCI driver to access PCI controller registers in PCI configuration space.
|
|
|
|
@param This A pointer to the EFI_PCI_IO_PROTOCOL instance.
|
|
@param Width Signifies the width of the memory operations.
|
|
@param Offset The offset within the PCI configuration space for the PCI controller.
|
|
@param Count The number of PCI configuration operations to perform.
|
|
@param Buffer For read operations, the destination buffer to store the results. For write
|
|
operations, the source buffer to write data from.
|
|
|
|
|
|
@retval EFI_SUCCESS The data was read from or written to the PCI controller.
|
|
@retval EFI_UNSUPPORTED The address range specified by Offset, Width, and Count is not
|
|
valid for the PCI configuration header of the PCI controller.
|
|
@retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources.
|
|
@retval EFI_INVALID_PARAMETER Buffer is NULL or Width is invalid.
|
|
|
|
**/
|
|
typedef
|
|
EFI_STATUS
|
|
(EFIAPI *EFI_PCI_IO_PROTOCOL_CONFIG)(
|
|
IN EFI_PCI_IO_PROTOCOL *This,
|
|
IN EFI_PCI_IO_PROTOCOL_WIDTH Width,
|
|
IN UINT32 Offset,
|
|
IN UINTN Count,
|
|
IN OUT VOID *Buffer
|
|
);
|
|
|
|
typedef struct {
|
|
EFI_PCI_IO_PROTOCOL_CONFIG Read;
|
|
EFI_PCI_IO_PROTOCOL_CONFIG Write;
|
|
} EFI_PCI_IO_PROTOCOL_CONFIG_ACCESS;
|
|
|
|
/**
|
|
Enables a PCI driver to copy one region of PCI memory space to another region of PCI
|
|
memory space.
|
|
|
|
@param This A pointer to the EFI_PCI_IO_PROTOCOL instance.
|
|
@param Width Signifies the width of the memory operations.
|
|
@param DestBarIndex The BAR index in the standard PCI Configuration header to use as the
|
|
base address for the memory operation to perform.
|
|
@param DestOffset The destination offset within the BAR specified by DestBarIndex to
|
|
start the memory writes for the copy operation.
|
|
@param SrcBarIndex The BAR index in the standard PCI Configuration header to use as the
|
|
base address for the memory operation to perform.
|
|
@param SrcOffset The source offset within the BAR specified by SrcBarIndex to start
|
|
the memory reads for the copy operation.
|
|
@param Count The number of memory operations to perform. Bytes moved is Width
|
|
size * Count, starting at DestOffset and SrcOffset.
|
|
|
|
@retval EFI_SUCCESS The data was copied from one memory region to another memory region.
|
|
@retval EFI_UNSUPPORTED DestBarIndex not valid for this PCI controller.
|
|
@retval EFI_UNSUPPORTED SrcBarIndex not valid for this PCI controller.
|
|
@retval EFI_UNSUPPORTED The address range specified by DestOffset, Width, and Count
|
|
is not valid for the PCI BAR specified by DestBarIndex.
|
|
@retval EFI_UNSUPPORTED The address range specified by SrcOffset, Width, and Count is
|
|
not valid for the PCI BAR specified by SrcBarIndex.
|
|
@retval EFI_INVALID_PARAMETER Width is invalid.
|
|
@retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources.
|
|
|
|
**/
|
|
typedef
|
|
EFI_STATUS
|
|
(EFIAPI *EFI_PCI_IO_PROTOCOL_COPY_MEM)(
|
|
IN EFI_PCI_IO_PROTOCOL *This,
|
|
IN EFI_PCI_IO_PROTOCOL_WIDTH Width,
|
|
IN UINT8 DestBarIndex,
|
|
IN UINT64 DestOffset,
|
|
IN UINT8 SrcBarIndex,
|
|
IN UINT64 SrcOffset,
|
|
IN UINTN Count
|
|
);
|
|
|
|
/**
|
|
Provides the PCI controller-Cspecific addresses needed to access system memory.
|
|
|
|
@param This A pointer to the EFI_PCI_IO_PROTOCOL instance.
|
|
@param Operation Indicates if the bus master is going to read or write to system memory.
|
|
@param HostAddress The system memory address to map to the PCI controller.
|
|
@param NumberOfBytes On input the number of bytes to map. On output the number of bytes
|
|
that were mapped.
|
|
@param DeviceAddress The resulting map address for the bus master PCI controller to use to
|
|
access the hosts HostAddress.
|
|
@param Mapping A resulting value to pass to Unmap().
|
|
|
|
@retval EFI_SUCCESS The range was mapped for the returned NumberOfBytes.
|
|
@retval EFI_UNSUPPORTED The HostAddress cannot be mapped as a common buffer.
|
|
@retval EFI_INVALID_PARAMETER One or more parameters are invalid.
|
|
@retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources.
|
|
@retval EFI_DEVICE_ERROR The system hardware could not map the requested address.
|
|
|
|
**/
|
|
typedef
|
|
EFI_STATUS
|
|
(EFIAPI *EFI_PCI_IO_PROTOCOL_MAP)(
|
|
IN EFI_PCI_IO_PROTOCOL *This,
|
|
IN EFI_PCI_IO_PROTOCOL_OPERATION Operation,
|
|
IN VOID *HostAddress,
|
|
IN OUT UINTN *NumberOfBytes,
|
|
OUT EFI_PHYSICAL_ADDRESS *DeviceAddress,
|
|
OUT VOID **Mapping
|
|
);
|
|
|
|
/**
|
|
Completes the Map() operation and releases any corresponding resources.
|
|
|
|
@param This A pointer to the EFI_PCI_IO_PROTOCOL instance.
|
|
@param Mapping The mapping value returned from Map().
|
|
|
|
@retval EFI_SUCCESS The range was unmapped.
|
|
@retval EFI_DEVICE_ERROR The data was not committed to the target system memory.
|
|
|
|
**/
|
|
typedef
|
|
EFI_STATUS
|
|
(EFIAPI *EFI_PCI_IO_PROTOCOL_UNMAP)(
|
|
IN EFI_PCI_IO_PROTOCOL *This,
|
|
IN VOID *Mapping
|
|
);
|
|
|
|
/**
|
|
Allocates pages that are suitable for an EfiPciIoOperationBusMasterCommonBuffer
|
|
mapping.
|
|
|
|
@param This A pointer to the EFI_PCI_IO_PROTOCOL instance.
|
|
@param Type This parameter is not used and must be ignored.
|
|
@param MemoryType The type of memory to allocate, EfiBootServicesData or
|
|
EfiRuntimeServicesData.
|
|
@param Pages The number of pages to allocate.
|
|
@param HostAddress A pointer to store the base system memory address of the
|
|
allocated range.
|
|
@param Attributes The requested bit mask of attributes for the allocated range.
|
|
|
|
@retval EFI_SUCCESS The requested memory pages were allocated.
|
|
@retval EFI_UNSUPPORTED Attributes is unsupported. The only legal attribute bits are
|
|
MEMORY_WRITE_COMBINE and MEMORY_CACHED.
|
|
@retval EFI_INVALID_PARAMETER One or more parameters are invalid.
|
|
@retval EFI_OUT_OF_RESOURCES The memory pages could not be allocated.
|
|
|
|
**/
|
|
typedef
|
|
EFI_STATUS
|
|
(EFIAPI *EFI_PCI_IO_PROTOCOL_ALLOCATE_BUFFER)(
|
|
IN EFI_PCI_IO_PROTOCOL *This,
|
|
IN EFI_ALLOCATE_TYPE Type,
|
|
IN EFI_MEMORY_TYPE MemoryType,
|
|
IN UINTN Pages,
|
|
OUT VOID **HostAddress,
|
|
IN UINT64 Attributes
|
|
);
|
|
|
|
/**
|
|
Frees memory that was allocated with AllocateBuffer().
|
|
|
|
@param This A pointer to the EFI_PCI_IO_PROTOCOL instance.
|
|
@param Pages The number of pages to free.
|
|
@param HostAddress The base system memory address of the allocated range.
|
|
|
|
@retval EFI_SUCCESS The requested memory pages were freed.
|
|
@retval EFI_INVALID_PARAMETER The memory range specified by HostAddress and Pages
|
|
was not allocated with AllocateBuffer().
|
|
|
|
**/
|
|
typedef
|
|
EFI_STATUS
|
|
(EFIAPI *EFI_PCI_IO_PROTOCOL_FREE_BUFFER)(
|
|
IN EFI_PCI_IO_PROTOCOL *This,
|
|
IN UINTN Pages,
|
|
IN VOID *HostAddress
|
|
);
|
|
|
|
/**
|
|
Flushes all PCI posted write transactions from a PCI host bridge to system memory.
|
|
|
|
@param This A pointer to the EFI_PCI_IO_PROTOCOL instance.
|
|
|
|
@retval EFI_SUCCESS The PCI posted write transactions were flushed from the PCI host
|
|
bridge to system memory.
|
|
@retval EFI_DEVICE_ERROR The PCI posted write transactions were not flushed from the PCI
|
|
host bridge due to a hardware error.
|
|
|
|
**/
|
|
typedef
|
|
EFI_STATUS
|
|
(EFIAPI *EFI_PCI_IO_PROTOCOL_FLUSH)(
|
|
IN EFI_PCI_IO_PROTOCOL *This
|
|
);
|
|
|
|
/**
|
|
Retrieves this PCI controller's current PCI bus number, device number, and function number.
|
|
|
|
@param This A pointer to the EFI_PCI_IO_PROTOCOL instance.
|
|
@param SegmentNumber The PCI controller's current PCI segment number.
|
|
@param BusNumber The PCI controller's current PCI bus number.
|
|
@param DeviceNumber The PCI controller's current PCI device number.
|
|
@param FunctionNumber The PCI controller's current PCI function number.
|
|
|
|
@retval EFI_SUCCESS The PCI controller location was returned.
|
|
@retval EFI_INVALID_PARAMETER One or more parameters are invalid.
|
|
|
|
**/
|
|
typedef
|
|
EFI_STATUS
|
|
(EFIAPI *EFI_PCI_IO_PROTOCOL_GET_LOCATION)(
|
|
IN EFI_PCI_IO_PROTOCOL *This,
|
|
OUT UINTN *SegmentNumber,
|
|
OUT UINTN *BusNumber,
|
|
OUT UINTN *DeviceNumber,
|
|
OUT UINTN *FunctionNumber
|
|
);
|
|
|
|
/**
|
|
Performs an operation on the attributes that this PCI controller supports. The operations include
|
|
getting the set of supported attributes, retrieving the current attributes, setting the current
|
|
attributes, enabling attributes, and disabling attributes.
|
|
|
|
@param This A pointer to the EFI_PCI_IO_PROTOCOL instance.
|
|
@param Operation The operation to perform on the attributes for this PCI controller.
|
|
@param Attributes The mask of attributes that are used for Set, Enable, and Disable
|
|
operations.
|
|
@param Result A pointer to the result mask of attributes that are returned for the Get
|
|
and Supported operations.
|
|
|
|
@retval EFI_SUCCESS The operation on the PCI controller's attributes was completed.
|
|
@retval EFI_INVALID_PARAMETER One or more parameters are invalid.
|
|
@retval EFI_UNSUPPORTED one or more of the bits set in
|
|
Attributes are not supported by this PCI controller or one of
|
|
its parent bridges when Operation is Set, Enable or Disable.
|
|
|
|
**/
|
|
typedef
|
|
EFI_STATUS
|
|
(EFIAPI *EFI_PCI_IO_PROTOCOL_ATTRIBUTES)(
|
|
IN EFI_PCI_IO_PROTOCOL *This,
|
|
IN EFI_PCI_IO_PROTOCOL_ATTRIBUTE_OPERATION Operation,
|
|
IN UINT64 Attributes,
|
|
OUT UINT64 *Result OPTIONAL
|
|
);
|
|
|
|
/**
|
|
Gets the attributes that this PCI controller supports setting on a BAR using
|
|
SetBarAttributes(), and retrieves the list of resource descriptors for a BAR.
|
|
|
|
@param This A pointer to the EFI_PCI_IO_PROTOCOL instance.
|
|
@param BarIndex The BAR index of the standard PCI Configuration header to use as the
|
|
base address for resource range. The legal range for this field is 0..5.
|
|
@param Supports A pointer to the mask of attributes that this PCI controller supports
|
|
setting for this BAR with SetBarAttributes().
|
|
@param Resources A pointer to the ACPI 2.0 resource descriptors that describe the current
|
|
configuration of this BAR of the PCI controller.
|
|
|
|
@retval EFI_SUCCESS If Supports is not NULL, then the attributes that the PCI
|
|
controller supports are returned in Supports. If Resources
|
|
is not NULL, then the ACPI 2.0 resource descriptors that the PCI
|
|
controller is currently using are returned in Resources.
|
|
@retval EFI_INVALID_PARAMETER Both Supports and Attributes are NULL.
|
|
@retval EFI_UNSUPPORTED BarIndex not valid for this PCI controller.
|
|
@retval EFI_OUT_OF_RESOURCES There are not enough resources available to allocate
|
|
Resources.
|
|
|
|
**/
|
|
typedef
|
|
EFI_STATUS
|
|
(EFIAPI *EFI_PCI_IO_PROTOCOL_GET_BAR_ATTRIBUTES)(
|
|
IN EFI_PCI_IO_PROTOCOL *This,
|
|
IN UINT8 BarIndex,
|
|
OUT UINT64 *Supports, OPTIONAL
|
|
OUT VOID **Resources OPTIONAL
|
|
);
|
|
|
|
/**
|
|
Sets the attributes for a range of a BAR on a PCI controller.
|
|
|
|
@param This A pointer to the EFI_PCI_IO_PROTOCOL instance.
|
|
@param Attributes The mask of attributes to set for the resource range specified by
|
|
BarIndex, Offset, and Length.
|
|
@param BarIndex The BAR index of the standard PCI Configuration header to use as the
|
|
base address for resource range. The legal range for this field is 0..5.
|
|
@param Offset A pointer to the BAR relative base address of the resource range to be
|
|
modified by the attributes specified by Attributes.
|
|
@param Length A pointer to the length of the resource range to be modified by the
|
|
attributes specified by Attributes.
|
|
|
|
@retval EFI_SUCCESS The set of attributes specified by Attributes for the resource
|
|
range specified by BarIndex, Offset, and Length were
|
|
set on the PCI controller, and the actual resource range is returned
|
|
in Offset and Length.
|
|
@retval EFI_INVALID_PARAMETER Offset or Length is NULL.
|
|
@retval EFI_UNSUPPORTED BarIndex not valid for this PCI controller.
|
|
@retval EFI_OUT_OF_RESOURCES There are not enough resources to set the attributes on the
|
|
resource range specified by BarIndex, Offset, and
|
|
Length.
|
|
|
|
**/
|
|
typedef
|
|
EFI_STATUS
|
|
(EFIAPI *EFI_PCI_IO_PROTOCOL_SET_BAR_ATTRIBUTES)(
|
|
IN EFI_PCI_IO_PROTOCOL *This,
|
|
IN UINT64 Attributes,
|
|
IN UINT8 BarIndex,
|
|
IN OUT UINT64 *Offset,
|
|
IN OUT UINT64 *Length
|
|
);
|
|
|
|
/**
|
|
@par Protocol Description:
|
|
The EFI_PCI_IO_PROTOCOL provides the basic Memory, I/O, PCI configuration,
|
|
and DMA interfaces that are used to abstract accesses to PCI controllers.
|
|
There is one EFI_PCI_IO_PROTOCOL instance for each PCI controller on a PCI bus.
|
|
A device driver that wishes to manage a PCI controller in a system will have to
|
|
retrieve the EFI_PCI_IO_PROTOCOL instance that is associated with the PCI controller.
|
|
**/
|
|
struct _EFI_PCI_IO_PROTOCOL {
|
|
EFI_PCI_IO_PROTOCOL_POLL_IO_MEM PollMem;
|
|
EFI_PCI_IO_PROTOCOL_POLL_IO_MEM PollIo;
|
|
EFI_PCI_IO_PROTOCOL_ACCESS Mem;
|
|
EFI_PCI_IO_PROTOCOL_ACCESS Io;
|
|
EFI_PCI_IO_PROTOCOL_CONFIG_ACCESS Pci;
|
|
EFI_PCI_IO_PROTOCOL_COPY_MEM CopyMem;
|
|
EFI_PCI_IO_PROTOCOL_MAP Map;
|
|
EFI_PCI_IO_PROTOCOL_UNMAP Unmap;
|
|
EFI_PCI_IO_PROTOCOL_ALLOCATE_BUFFER AllocateBuffer;
|
|
EFI_PCI_IO_PROTOCOL_FREE_BUFFER FreeBuffer;
|
|
EFI_PCI_IO_PROTOCOL_FLUSH Flush;
|
|
EFI_PCI_IO_PROTOCOL_GET_LOCATION GetLocation;
|
|
EFI_PCI_IO_PROTOCOL_ATTRIBUTES Attributes;
|
|
EFI_PCI_IO_PROTOCOL_GET_BAR_ATTRIBUTES GetBarAttributes;
|
|
EFI_PCI_IO_PROTOCOL_SET_BAR_ATTRIBUTES SetBarAttributes;
|
|
|
|
///
|
|
/// The size, in bytes, of the ROM image.
|
|
///
|
|
UINT64 RomSize;
|
|
|
|
///
|
|
/// A pointer to the in memory copy of the ROM image. The PCI Bus Driver is responsible
|
|
/// for allocating memory for the ROM image, and copying the contents of the ROM to memory.
|
|
/// The contents of this buffer are either from the PCI option ROM that can be accessed
|
|
/// through the ROM BAR of the PCI controller, or it is from a platform-specific location.
|
|
/// The Attributes() function can be used to determine from which of these two sources
|
|
/// the RomImage buffer was initialized.
|
|
///
|
|
VOID *RomImage;
|
|
};
|
|
|
|
extern EFI_GUID gEfiPciIoProtocolGuid;
|
|
|
|
#endif
|