audk/ArmPlatformPkg/Include/Drivers/PL011Uart.h

260 lines
10 KiB
C

/** @file
*
* Copyright (c) 2011-2016, ARM Limited. All rights reserved.
*
* This program and the accompanying materials
* are licensed and made available under the terms and conditions of the BSD License
* which accompanies this distribution. The full text of the license may be found at
* http://opensource.org/licenses/bsd-license.php
*
* THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
* WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
*
**/
#ifndef __PL011_UART_H__
#define __PL011_UART_H__
#include <Uefi.h>
#include <Protocol/SerialIo.h>
// PL011 Registers
#define UARTDR 0x000
#define UARTRSR 0x004
#define UARTECR 0x004
#define UARTFR 0x018
#define UARTILPR 0x020
#define UARTIBRD 0x024
#define UARTFBRD 0x028
#define UARTLCR_H 0x02C
#define UARTCR 0x030
#define UARTIFLS 0x034
#define UARTIMSC 0x038
#define UARTRIS 0x03C
#define UARTMIS 0x040
#define UARTICR 0x044
#define UARTDMACR 0x048
#define UARTPID0 0xFE0
#define UARTPID1 0xFE4
#define UARTPID2 0xFE8
#define UARTPID3 0xFEC
// Data status bits
#define UART_DATA_ERROR_MASK 0x0F00
// Status reg bits
#define UART_STATUS_ERROR_MASK 0x0F
// Flag reg bits
#define PL011_UARTFR_RI (1 << 8) // Ring indicator
#define PL011_UARTFR_TXFE (1 << 7) // Transmit FIFO empty
#define PL011_UARTFR_RXFF (1 << 6) // Receive FIFO full
#define PL011_UARTFR_TXFF (1 << 5) // Transmit FIFO full
#define PL011_UARTFR_RXFE (1 << 4) // Receive FIFO empty
#define PL011_UARTFR_BUSY (1 << 3) // UART busy
#define PL011_UARTFR_DCD (1 << 2) // Data carrier detect
#define PL011_UARTFR_DSR (1 << 1) // Data set ready
#define PL011_UARTFR_CTS (1 << 0) // Clear to send
// Flag reg bits - alternative names
#define UART_TX_EMPTY_FLAG_MASK PL011_UARTFR_TXFE
#define UART_RX_FULL_FLAG_MASK PL011_UARTFR_RXFF
#define UART_TX_FULL_FLAG_MASK PL011_UARTFR_TXFF
#define UART_RX_EMPTY_FLAG_MASK PL011_UARTFR_RXFE
#define UART_BUSY_FLAG_MASK PL011_UARTFR_BUSY
// Control reg bits
#define PL011_UARTCR_CTSEN (1 << 15) // CTS hardware flow control enable
#define PL011_UARTCR_RTSEN (1 << 14) // RTS hardware flow control enable
#define PL011_UARTCR_RTS (1 << 11) // Request to send
#define PL011_UARTCR_DTR (1 << 10) // Data transmit ready.
#define PL011_UARTCR_RXE (1 << 9) // Receive enable
#define PL011_UARTCR_TXE (1 << 8) // Transmit enable
#define PL011_UARTCR_LBE (1 << 7) // Loopback enable
#define PL011_UARTCR_UARTEN (1 << 0) // UART Enable
// Line Control Register Bits
#define PL011_UARTLCR_H_SPS (1 << 7) // Stick parity select
#define PL011_UARTLCR_H_WLEN_8 (3 << 5)
#define PL011_UARTLCR_H_WLEN_7 (2 << 5)
#define PL011_UARTLCR_H_WLEN_6 (1 << 5)
#define PL011_UARTLCR_H_WLEN_5 (0 << 5)
#define PL011_UARTLCR_H_FEN (1 << 4) // FIFOs Enable
#define PL011_UARTLCR_H_STP2 (1 << 3) // Two stop bits select
#define PL011_UARTLCR_H_EPS (1 << 2) // Even parity select
#define PL011_UARTLCR_H_PEN (1 << 1) // Parity Enable
#define PL011_UARTLCR_H_BRK (1 << 0) // Send break
#define PL011_UARTPID2_VER(X) (((X) >> 4) & 0xF)
#define PL011_VER_R1P4 0x2
/**
Initialise the serial port to the specified settings.
All unspecified settings will be set to the default values.
@param[in] UartBase The base address of the serial device.
@param[in] UartClkInHz The clock in Hz for the serial device.
Ignored if the PCD PL011UartInteger is not 0
@param[in out] BaudRate The baud rate of the serial device. If the
baud rate is not supported, the speed will be
reduced to the nearest supported one and the
variable's value will be updated accordingly.
@param[in out] ReceiveFifoDepth The number of characters the device will
buffer on input. Value of 0 will use the
device's default FIFO depth.
@param[in out] Parity If applicable, this is the EFI_PARITY_TYPE
that is computed or checked as each character
is transmitted or received. If the device
does not support parity, the value is the
default parity value.
@param[in out] DataBits The number of data bits in each character.
@param[in out] StopBits If applicable, the EFI_STOP_BITS_TYPE number
of stop bits per character.
If the device does not support stop bits, the
value is the default stop bit value.
@retval RETURN_SUCCESS All attributes were set correctly on the
serial device.
@retval RETURN_INVALID_PARAMETER One or more of the attributes has an
unsupported value.
**/
RETURN_STATUS
EFIAPI
PL011UartInitializePort (
IN UINTN UartBase,
IN UINT32 UartClkInHz,
IN OUT UINT64 *BaudRate,
IN OUT UINT32 *ReceiveFifoDepth,
IN OUT EFI_PARITY_TYPE *Parity,
IN OUT UINT8 *DataBits,
IN OUT EFI_STOP_BITS_TYPE *StopBits
);
/**
Assert or deassert the control signals on a serial port.
The following control signals are set according their bit settings :
. Request to Send
. Data Terminal Ready
@param[in] UartBase UART registers base address
@param[in] Control The following bits are taken into account :
. EFI_SERIAL_REQUEST_TO_SEND : assert/deassert the
"Request To Send" control signal if this bit is
equal to one/zero.
. EFI_SERIAL_DATA_TERMINAL_READY : assert/deassert
the "Data Terminal Ready" control signal if this
bit is equal to one/zero.
. EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE : enable/disable
the hardware loopback if this bit is equal to
one/zero.
. EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE : not supported.
. EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE : enable/
disable the hardware flow control based on CTS (Clear
To Send) and RTS (Ready To Send) control signals.
@retval RETURN_SUCCESS The new control bits were set on the device.
@retval RETURN_UNSUPPORTED The device does not support this operation.
**/
RETURN_STATUS
EFIAPI
PL011UartSetControl (
IN UINTN UartBase,
IN UINT32 Control
);
/**
Retrieve the status of the control bits on a serial device.
@param[in] UartBase UART registers base address
@param[out] Control Status of the control bits on a serial device :
. EFI_SERIAL_DATA_CLEAR_TO_SEND,
EFI_SERIAL_DATA_SET_READY,
EFI_SERIAL_RING_INDICATE,
EFI_SERIAL_CARRIER_DETECT,
EFI_SERIAL_REQUEST_TO_SEND,
EFI_SERIAL_DATA_TERMINAL_READY
are all related to the DTE (Data Terminal Equipment)
and DCE (Data Communication Equipment) modes of
operation of the serial device.
. EFI_SERIAL_INPUT_BUFFER_EMPTY : equal to one if the
receive buffer is empty, 0 otherwise.
. EFI_SERIAL_OUTPUT_BUFFER_EMPTY : equal to one if the
transmit buffer is empty, 0 otherwise.
. EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE : equal to one if
the hardware loopback is enabled (the ouput feeds the
receive buffer), 0 otherwise.
. EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE : equal to one if
a loopback is accomplished by software, 0 otherwise.
. EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE : equal to
one if the hardware flow control based on CTS (Clear
To Send) and RTS (Ready To Send) control signals is
enabled, 0 otherwise.
@retval RETURN_SUCCESS The control bits were read from the serial device.
**/
RETURN_STATUS
EFIAPI
PL011UartGetControl (
IN UINTN UartBase,
OUT UINT32 *Control
);
/**
Write data to serial device.
@param Buffer Point of data buffer which need to be written.
@param NumberOfBytes Number of output bytes which are cached in Buffer.
@retval 0 Write data failed.
@retval !0 Actual number of bytes written to serial device.
**/
UINTN
EFIAPI
PL011UartWrite (
IN UINTN UartBase,
IN UINT8 *Buffer,
IN UINTN NumberOfBytes
);
/**
Read data from serial device and save the data in buffer.
@param Buffer Point of data buffer which need to be written.
@param NumberOfBytes Number of output bytes which are cached in Buffer.
@retval 0 Read data failed.
@retval !0 Actual number of bytes read from serial device.
**/
UINTN
EFIAPI
PL011UartRead (
IN UINTN UartBase,
OUT UINT8 *Buffer,
IN UINTN NumberOfBytes
);
/**
Check to see if any data is available to be read from the debug device.
@retval TRUE At least one byte of data is available to be read
@retval FALSE No data is available to be read
**/
BOOLEAN
EFIAPI
PL011UartPoll (
IN UINTN UartBase
);
#endif