mirror of https://github.com/acidanthera/audk.git
83 lines
4.4 KiB
Plaintext
83 lines
4.4 KiB
Plaintext
================================================================================
|
|
Build And Integration Instructions
|
|
2014 June 24th
|
|
================================================================================
|
|
|
|
================================================================================
|
|
DISCLAIMER
|
|
================================================================================
|
|
This release note as well as the software described in it is furnished under license
|
|
and may only be used or copied in accordance with the terms of the license. The
|
|
information in this manual is furnished for informational use only, is subject to
|
|
change without notice, and should not be construed as a commitment by Intel Corporation.
|
|
Intel Corporation assumes no responsibility or liability for any errors or inaccuracies
|
|
that may appear in this document or any software that may be provided in association
|
|
with this document.
|
|
Except as permitted by such license, no part of this document may be reproduced,
|
|
stored in a retrieval system, or transmitted in any form or by any means without
|
|
the express written consent of Intel Corporation.
|
|
|
|
================================================================================
|
|
INDEX
|
|
================================================================================
|
|
A. INTRODUCTION
|
|
B. HOW TO BUILD
|
|
C. HOW TO INTEGRATE
|
|
|
|
================================================================================
|
|
A. INTRODUCTION
|
|
================================================================================
|
|
This document provides instructions on how to build Coreboot Uefi Payload and
|
|
how to integrate it into coreboot firmware.
|
|
|
|
================================================================================
|
|
B. HOW TO BUILD
|
|
================================================================================
|
|
1. Run the below two commands in windows command prompt window:
|
|
edksetup.bat
|
|
|
|
For debug ia32 build:
|
|
build -a IA32 -p CorebootPayloadPkg\CorebootPayloadPkgIa32.dsc -b DEBUG -t <ToolChain>
|
|
|
|
For release ia32 build:
|
|
build -a IA32 -p CorebootPayloadPkg\CorebootPayloadPkgIa32.dsc -b RELEASE -t <ToolChain>
|
|
|
|
For debug X64 build:
|
|
build -a IA32 -a X64 -p CorebootPayloadPkg\CorebootPayloadPkgIa32X64.dsc -b DEBUG -t <ToolChain>
|
|
|
|
For release X64 build:
|
|
build -a IA32 -a X64 -p CorebootPayloadPkg\CorebootPayloadPkgIa32X64.dsc -b RELEASE -t <ToolChain>
|
|
|
|
<ToolChain> is the EDK II build environment on your host. Currently it was tested with VS2008x64 toolchain.
|
|
|
|
For details about EDK II build steps, refer to http://svn.code.sf.net/p/edk2/code/branches/UDK2014/BuildNotes2.txt
|
|
|
|
2. If build is successfully, the payload image (UEFIPAYLOAD.fd) will be generated inside the folder of Build\CorebootPayloadPkg.
|
|
|
|
================================================================================
|
|
C. HOW TO INTEGRATE
|
|
================================================================================
|
|
1. Copy the payload image (UEFIPAYLOAD.fd) into the top-level directory of Coreboot source tree.
|
|
2. Run "make menuconfig" in linux console to start Coreboot configuration surface.
|
|
3. In the Payload section,
|
|
1) Choose "An ELF executable payload" for the option of "Add a payload".
|
|
2) Type the path of payload image for the option of "Payload path and filename".
|
|
3) Select the option of "Use LZMA compression for payloads".
|
|
|
|
4. If the graphics console is required in Coreboot UEFI payload, running VGA option rom should be enabled.
|
|
For details:
|
|
1) In the Device section, select the option of "Run VGA Option ROMs".
|
|
2) In the VGA BIOS section, select the option of "Add a VGA BIOS Image", Input the path of vga bios image
|
|
for the option of VGA BIOS path and filename, give the values of vendor id and device id for the option
|
|
of "VGA device PCI IDs".
|
|
3) In the Display section,
|
|
Select the option of "Set framebuffer graphics resolution"
|
|
Choose a right display mode for the option of "framebuffer graphics resolution".
|
|
Note: If the boot OS is windows, please choose the display mode supporting 32 bit color.
|
|
Select the option of "Keep VESA framebuffer"
|
|
|
|
5. Press ESC key to exit the Coreboot configuration surface. If there is a question prompted like "Do you wish to save your new configuration?",
|
|
choose Yes.
|
|
|
|
6. Run "make" to build the coreboot firmware image.
|