mirror of https://github.com/acidanthera/audk.git
178 lines
6.2 KiB
C
178 lines
6.2 KiB
C
/** @file
|
|
*
|
|
* Copyright (c) 2011, ARM Limited. All rights reserved.
|
|
*
|
|
* This program and the accompanying materials
|
|
* are licensed and made available under the terms and conditions of the BSD License
|
|
* which accompanies this distribution. The full text of the license may be found at
|
|
* http://opensource.org/licenses/bsd-license.php
|
|
*
|
|
* THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
|
|
* WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
|
|
*
|
|
**/
|
|
|
|
#include <Library/IoLib.h>
|
|
#include <Library/ArmTrustZoneLib.h>
|
|
#include <Library/ArmPlatformLib.h>
|
|
#include <Library/DebugLib.h>
|
|
#include <Library/PcdLib.h>
|
|
#include <Drivers/PL341Dmc.h>
|
|
#include <Drivers/PL301Axi.h>
|
|
#include <Library/L2X0CacheLib.h>
|
|
#include <Library/SerialPortLib.h>
|
|
|
|
#define SerialPrint(txt) SerialPortWrite (txt, AsciiStrLen(txt)+1);
|
|
|
|
// DDR2 timings
|
|
struct pl341_dmc_config ddr_timings = {
|
|
.base = ARM_VE_DMC_BASE,
|
|
.has_qos = 1,
|
|
.refresh_prd = 0x3D0,
|
|
.cas_latency = 0x8,
|
|
.write_latency = 0x3,
|
|
.t_mrd = 0x2,
|
|
.t_ras = 0xA,
|
|
.t_rc = 0xE,
|
|
.t_rcd = 0x104,
|
|
.t_rfc = 0x2f32,
|
|
.t_rp = 0x14,
|
|
.t_rrd = 0x2,
|
|
.t_wr = 0x4,
|
|
.t_wtr = 0x2,
|
|
.t_xp = 0x2,
|
|
.t_xsr = 0xC8,
|
|
.t_esr = 0x14,
|
|
.memory_cfg = DMC_MEMORY_CONFIG_ACTIVE_CHIP_1 | DMC_MEMORY_CONFIG_BURST_4 |
|
|
DMC_MEMORY_CONFIG_ROW_ADDRESS_15 | DMC_MEMORY_CONFIG_COLUMN_ADDRESS_10,
|
|
.memory_cfg2 = DMC_MEMORY_CFG2_DQM_INIT | DMC_MEMORY_CFG2_CKE_INIT |
|
|
DMC_MEMORY_CFG2_BANK_BITS_3 | DMC_MEMORY_CFG2_MEM_WIDTH_32,
|
|
.memory_cfg3 = 0x00000001,
|
|
.chip_cfg0 = 0x00010000,
|
|
.t_faw = 0x00000A0D,
|
|
};
|
|
|
|
/**
|
|
Return if Trustzone is supported by your platform
|
|
|
|
A non-zero value must be returned if you want to support a Secure World on your platform.
|
|
ArmVExpressTrustzoneInit() will later set up the secure regions.
|
|
This function can return 0 even if Trustzone is supported by your processor. In this case,
|
|
the platform will continue to run in Secure World.
|
|
|
|
@return A non-zero value if Trustzone supported.
|
|
|
|
**/
|
|
UINTN ArmPlatformTrustzoneSupported(VOID) {
|
|
return (MmioRead32(ARM_VE_SYS_CFGRW1_REG) & ARM_VE_CFGRW1_TZASC_EN_BIT_MASK);
|
|
}
|
|
|
|
/**
|
|
Initialize the Secure peripherals and memory regions
|
|
|
|
If Trustzone is supported by your platform then this function makes the required initialization
|
|
of the secure peripherals and memory regions.
|
|
|
|
**/
|
|
VOID ArmPlatformTrustzoneInit(VOID) {
|
|
//
|
|
// Setup TZ Protection Controller
|
|
//
|
|
|
|
// Set Non Secure access for all devices
|
|
TZPCSetDecProtBits(ARM_VE_TZPC_BASE, TZPC_DECPROT_0, 0xFFFFFFFF);
|
|
TZPCSetDecProtBits(ARM_VE_TZPC_BASE, TZPC_DECPROT_1, 0xFFFFFFFF);
|
|
TZPCSetDecProtBits(ARM_VE_TZPC_BASE, TZPC_DECPROT_2, 0xFFFFFFFF);
|
|
|
|
// Remove Non secure access to secure devices
|
|
TZPCClearDecProtBits(ARM_VE_TZPC_BASE, TZPC_DECPROT_0,
|
|
ARM_VE_DECPROT_BIT_TZPC | ARM_VE_DECPROT_BIT_DMC_TZASC | ARM_VE_DECPROT_BIT_NMC_TZASC | ARM_VE_DECPROT_BIT_SMC_TZASC);
|
|
|
|
TZPCClearDecProtBits(ARM_VE_TZPC_BASE, TZPC_DECPROT_2,
|
|
ARM_VE_DECPROT_BIT_EXT_MAST_TZ | ARM_VE_DECPROT_BIT_DMC_TZASC_LOCK | ARM_VE_DECPROT_BIT_NMC_TZASC_LOCK | ARM_VE_DECPROT_BIT_SMC_TZASC_LOCK);
|
|
|
|
|
|
//
|
|
// Setup TZ Address Space Controller for the SMC. Create 5 Non Secure regions (NOR0, NOR1, SRAM, SMC Peripheral regions)
|
|
//
|
|
|
|
// NOR Flash 0 non secure (BootMon)
|
|
TZASCSetRegion(ARM_VE_TZASC_BASE,1,TZASC_REGION_ENABLED,
|
|
ARM_VE_SMB_NOR0_BASE,0,
|
|
TZASC_REGION_SIZE_64MB, TZASC_REGION_SECURITY_NSRW);
|
|
|
|
// NOR Flash 1. The first half of the NOR Flash1 must be secure for the secure firmware (sec_uefi.bin)
|
|
#if EDK2_ARMVE_SECURE_SYSTEM
|
|
//Note: Your OS Kernel must be aware of the secure regions before to enable this region
|
|
TZASCSetRegion(ARM_VE_TZASC_BASE,2,TZASC_REGION_ENABLED,
|
|
ARM_VE_SMB_NOR1_BASE + SIZE_32MB,0,
|
|
TZASC_REGION_SIZE_32MB, TZASC_REGION_SECURITY_NSRW);
|
|
#else
|
|
TZASCSetRegion(ARM_VE_TZASC_BASE,2,TZASC_REGION_ENABLED,
|
|
ARM_VE_SMB_NOR1_BASE,0,
|
|
TZASC_REGION_SIZE_64MB, TZASC_REGION_SECURITY_NSRW);
|
|
#endif
|
|
|
|
// Base of SRAM. Only half of SRAM in Non Secure world
|
|
// First half non secure (16MB) + Second Half secure (16MB) = 32MB of SRAM
|
|
#if EDK2_ARMVE_SECURE_SYSTEM
|
|
//Note: Your OS Kernel must be aware of the secure regions before to enable this region
|
|
TZASCSetRegion(ARM_VE_TZASC_BASE,3,TZASC_REGION_ENABLED,
|
|
ARM_VE_SMB_SRAM_BASE,0,
|
|
TZASC_REGION_SIZE_16MB, TZASC_REGION_SECURITY_NSRW);
|
|
#else
|
|
TZASCSetRegion(ARM_VE_TZASC_BASE,3,TZASC_REGION_ENABLED,
|
|
ARM_VE_SMB_SRAM_BASE,0,
|
|
TZASC_REGION_SIZE_32MB, TZASC_REGION_SECURITY_NSRW);
|
|
#endif
|
|
|
|
// Memory Mapped Peripherals. All in non secure world
|
|
TZASCSetRegion(ARM_VE_TZASC_BASE,4,TZASC_REGION_ENABLED,
|
|
ARM_VE_SMB_PERIPH_BASE,0,
|
|
TZASC_REGION_SIZE_64MB, TZASC_REGION_SECURITY_NSRW);
|
|
|
|
// MotherBoard Peripherals and On-chip peripherals.
|
|
TZASCSetRegion(ARM_VE_TZASC_BASE,5,TZASC_REGION_ENABLED,
|
|
ARM_VE_SMB_MB_ON_CHIP_PERIPH_BASE,0,
|
|
TZASC_REGION_SIZE_256MB, TZASC_REGION_SECURITY_NSRW);
|
|
}
|
|
|
|
/**
|
|
Remap the memory at 0x0
|
|
|
|
Some platform requires or gives the ability to remap the memory at the address 0x0.
|
|
This function can do nothing if this feature is not relevant to your platform.
|
|
|
|
**/
|
|
VOID ArmPlatformBootRemapping(VOID) {
|
|
UINT32 val32 = MmioRead32(ARM_VE_SYS_CFGRW1_REG); //Scc - CFGRW1
|
|
// we remap the DRAM to 0x0
|
|
MmioWrite32(ARM_VE_SYS_CFGRW1_REG, (val32 & 0x0FFFFFFF) | ARM_VE_CFGRW1_REMAP_DRAM);
|
|
}
|
|
|
|
/**
|
|
Initialize controllers that must setup at the early stage
|
|
|
|
Some peripherals must be initialized in Secure World.
|
|
For example, some L2x0 requires to be initialized in Secure World
|
|
|
|
**/
|
|
VOID
|
|
ArmPlatformInitialize (
|
|
VOID
|
|
) {
|
|
// The L2x0 controller must be intialize in Secure World
|
|
L2x0CacheInit(PcdGet32(PcdL2x0ControllerBase), FALSE);
|
|
}
|
|
|
|
/**
|
|
Initialize the system (or sometimes called permanent) memory
|
|
|
|
This memory is generally represented by the DRAM.
|
|
|
|
**/
|
|
VOID ArmPlatformInitializeSystemMemory(VOID) {
|
|
PL341DmcInit(&ddr_timings);
|
|
PL301AxiInit(ARM_VE_FAXI_BASE);
|
|
}
|