75 lines
3.3 KiB
Perl
75 lines
3.3 KiB
Perl
#
|
|
# Copyright 2015 Centreon (http://www.centreon.com/)
|
|
#
|
|
# Centreon is a full-fledged industry-strength solution that meets
|
|
# the needs in IT infrastructure and application monitoring for
|
|
# service performance.
|
|
#
|
|
# Licensed under the Apache License, Version 2.0 (the "License");
|
|
# you may not use this file except in compliance with the License.
|
|
# You may obtain a copy of the License at
|
|
#
|
|
# http://www.apache.org/licenses/LICENSE-2.0
|
|
#
|
|
# Unless required by applicable law or agreed to in writing, software
|
|
# distributed under the License is distributed on an "AS IS" BASIS,
|
|
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
# See the License for the specific language governing permissions and
|
|
# limitations under the License.
|
|
#
|
|
|
|
package storage::emc::celerra::local::mode::components::datamover;
|
|
|
|
use strict;
|
|
use warnings;
|
|
|
|
my %map_dm_status = (
|
|
0 => 'Reset (or unknown state)',
|
|
1 => 'DOS boot phase, BIOS check, boot sequence',
|
|
2 => 'SIB POST failures (that is, hardware failures)',
|
|
3 => 'DART is loaded on Data Mover, DOS boot and execution of boot.bat, boot.cfg',
|
|
4 => 'DART is ready on Data Mover, running, and MAC threads started',
|
|
5 => 'DART is in contact with Control Station box monitor',
|
|
7 => 'DART is in panic state',
|
|
9 => 'DART reboot is pending or in halted state',
|
|
13 => 'DART panicked and completed memory dump',
|
|
14 => 'DM Misc problems',
|
|
15 => 'Data Mover is flashing firmware. DART is flashing BIOS and/or POST firmware. Data Mover cannot be reset',
|
|
17 => 'Data Mover Hardware fault detected',
|
|
18 => 'DM Memory Test Failure. BIOS detected memory error',
|
|
19 => 'DM POST Test Failure. General POST error',
|
|
20 => 'DM POST NVRAM test failure. Invalid NVRAM content error',
|
|
21 => 'DM POST invalid peer Data Mover type',
|
|
22 => 'DM POST invalid Data Mover part number',
|
|
23 => 'DM POST Fibre Channel test failure. Error in blade Fibre connection',
|
|
24 => 'DM POST network test failure. Error in Ethernet controller',
|
|
25 => 'DM T2NET Error. Unable to get blade reason code due to management switch problems',
|
|
);
|
|
|
|
sub check {
|
|
my ($self) = @_;
|
|
|
|
$self->{output}->output_add(long_msg => "Checking data movers");
|
|
$self->{components}->{datamover} = {name => 'data movers', total => 0, skip => 0};
|
|
return if ($self->check_exclude(section => 'datamover'));
|
|
|
|
foreach my $line (split /\n/, $self->{stdout}) {
|
|
next if ($line !~ /^\s*(\d+)\s+-\s+(\S+)/);
|
|
my ($code, $instance) = ($1, $2);
|
|
next if (!defined($map_dm_status{$code}));
|
|
|
|
return if ($self->check_exclude(section => 'datamover', instance => $instance));
|
|
|
|
$self->{components}->{datamover}->{total}++;
|
|
$self->{output}->output_add(long_msg => sprintf("Data mover '%s' status is '%s'",
|
|
$instance, $map_dm_status{$code}));
|
|
my $exit = $self->get_severity(section => 'datamover', value => $map_dm_status{$code});
|
|
if (!$self->{output}->is_status(value => $exit, compare => 'ok', litteral => 1)) {
|
|
$self->{output}->output_add(severity => $exit,
|
|
short_msg => sprintf("Data mover '%s' status is '%s'",
|
|
$instance, $map_dm_status{$code}));
|
|
}
|
|
}
|
|
}
|
|
|
|
1; |