[channels.c channels.h clientloop.c]
Add an "ABANDONED" channel state and use for mux sessions that are
disconnected via the ~. escape sequence. Channels in this state will
be able to close if the server responds, but do not count as active channels.
This means that if you ~. all of the mux clients when using ControlPersist
on a broken network, the backgrounded mux master will exit when the
Control Persist time expires rather than hanging around indefinitely.
bz#1917, also reported and tested by tedu@. ok djm@ markus@.
[mux.c readconf.h channels.h compat.h compat.c ssh.c readconf.c channels.c version.h]
unbreak remote portforwarding with dynamic allocated listen ports:
1) send the actual listen port in the open message (instead of 0).
this allows multiple forwardings with a dynamic listen port
2) update the matching permit-open entry, so we can identify where
to connect to
report: den at skbkontur.ru and P. Szczygielski
feedback and ok djm@
[channels.c auth-options.c servconf.c channels.h sshd.8]
Add wildcard support to PermitOpen, allowing things like "PermitOpen
localhost:*". bz #1857, ok djm markus.
[channels.c channels.h clientloop.h mux.c ssh.c]
support for cancelling local and remote port forwards via the multiplex
socket. Use ssh -O cancel -L xx:xx:xx -R yy:yy:yy user@host" to request
the cancellation of the specified forwardings; ok markus@
[channels.c channels.h clientloop.c clientloop.h mux.c ssh.c]
hook up a channel confirm callback to warn the user then requested X11
forwarding was refused by the server; ok markus@
[channels.c channels.h mux.c ssh.c]
Pause the mux channel while waiting for reply from aynch callbacks.
Prevents misordering of replies if new requests arrive while waiting.
Extend channel open confirm callback to allow signalling failure
conditions as well as success. Use this to 1) fix a memory leak, 2)
start using the above pause mechanism and 3) delay sending a success/
failure message on mux slave session open until we receive a reply from
the server.
motivated by and with feedback from markus@
[channels.c channels.h clientloop.c clientloop.h mux.c nchan.c ssh.c]
rewrite ssh(1) multiplexing code to a more sensible protocol.
The new multiplexing code uses channels for the listener and
accepted control sockets to make the mux master non-blocking, so
no stalls when processing messages from a slave.
avoid use of fatal() in mux master protocol parsing so an errant slave
process cannot take down a running master.
implement requesting of port-forwards over multiplexed sessions. Any
port forwards requested by the slave are added to those the master has
established.
add support for stdio forwarding ("ssh -W host:port ...") in mux slaves.
document master/slave mux protocol so that other tools can use it to
control a running ssh(1). Note: there are no guarantees that this
protocol won't be incompatibly changed (though it is versioned).
feedback Salvador Fandino, dtucker@
channel changes ok markus@
[ssh_config channels.c ssh.1 channels.h ssh.c]
Add a 'netcat mode' (ssh -W). This connects stdio on the client to a
single port forward on the server. This allows, for example, using ssh as
a ProxyCommand to route connections via intermediate servers.
bz #1618, man page help from jmc@, ok markus@
[channels.c ssh.1 servconf.c sshd_config.5 sshd.c channels.h servconf.h
ssh-keyscan.1 ssh-keyscan.c readconf.c sshconnect.c misc.c ssh.c
readconf.h scp.1 sftp.1 ssh_config.5 misc.h]
Remove RoutingDomain from ssh since it's now not needed. It can be
replaced with "route exec" or "nc -V" as a proxycommand. "route exec"
also ensures that trafic such as DNS lookups stays withing the specified
routingdomain. For example (from reyk):
# route -T 2 exec /usr/sbin/sshd
or inherited from the parent process
$ route -T 2 exec sh
$ ssh 10.1.2.3
ok deraadt@ markus@ stevesk@ reyk@
[channels.c channels.h]
fix race condition in x11/agent channel allocation: don't read after
the end of the select read/write fdset and make sure a reused FD
is not touched before the pre-handlers are called.
with and ok djm@
[ssh_config.5 sshd.c misc.h ssh-keyscan.1 readconf.h sshconnect.c
channels.c channels.h servconf.h servconf.c ssh.1 ssh-keyscan.c scp.1
sftp.1 sshd_config.5 readconf.c ssh.c misc.c]
Allow to set the rdomain in ssh/sftp/scp/sshd and ssh-keyscan.
ok markus@
[canohost.c canohost.h channels.c channels.h clientloop.c readconf.c]
[readconf.h serverloop.c ssh.c]
support remote port forwarding with a zero listen port (-R0:...) to
dyamically allocate a listen port at runtime (this is actually
specified in rfc4254); bz#1003 ok markus@
[channels.c channels.h session.c]
make Channel->path an allocated string, saving a few bytes here and
there and fixing bz#1380 in the process; ok markus@
[channels.c channels.h session.c]
don't call isatty() on a pty master, instead pass a flag down to
channel_set_fds() indicating that te fds refer to a tty. Fixes a
hang on exit on Solaris (bz#1463) in portable but is actually
a generic bug; ok dtucker deraadt markus
[clientloop.h channels.h clientloop.c channels.c mux.c]
The multiplexing escape char handler commit last night introduced a
small memory leak per session; plug it.
[clientloop.h mux.c channels.c clientloop.c channels.h]
Enable ~ escapes for multiplex slave sessions; give each channel
its own escape state and hook the escape filters up to muxed
channels. bz #1331
Mux slaves do not currently support the ~^Z and ~& escapes.
NB. this change cranks the mux protocol version, so a new ssh
mux client will not be able to connect to a running old ssh
mux master.
ok dtucker@
[sshd.c channels.h channels.c log.c servconf.c log.h servconf.h sshd.8]
Add extended test mode (-T) and connection parameters for test mode (-C).
-T causes sshd to write its effective configuration to stdout and exit.
-C causes any relevant Match rules to be applied before output. The
combination allows tesing of the parser and config files. ok deraadt djm
[channels.h clientloop.c nchan.c serverloop.c]
unbreak
ssh -2 localhost od /bin/ls | true
ignoring SIGPIPE by adding a new channel message (EOW) that signals
the peer that we're not interested in any data it might send.
fixes bz #85; discussion, debugging and ok djm@
[channels.c channels.h clientloop.c serverloop.c]
Try additional addresses when connecting to a port forward destination
whose DNS name resolves to more than one address. The previous behaviour
was to try the first address and give up.
Reported by stig AT venaas.com in bz#343
great feedback and ok markus@
[auth-options.c auth1.c channels.c channels.h clientloop.c gss-serv.c]
[monitor.c monitor_wrap.c nchan.c servconf.c serverloop.c session.c]
[ssh.c sshd.c]
Implement a channel success/failure status confirmation callback
mechanism. Each channel maintains a queue of callbacks, which will
be drained in order (RFC4253 guarantees confirm messages are not
reordered within an channel).
Also includes a abandonment callback to clean up if a channel is
closed without sending confirmation messages. This probably
shouldn't happen in compliant implementations, but it could be
abused to leak memory.
ok markus@ (as part of a larger diff)
[channels.c channels.h servconf.c servconf.h sshd_config.5]
Make PermitOpen take a list of permitted ports and act more like most
other keywords (ie the first match is the effective setting). This
also makes it easier to override a previously set PermitOpen. ok djm@
[channels.c channels.h servconf.c sshd_config.5]
Add PermitOpen directive to sshd_config which is equivalent to the
"permitopen" key option. Allows server admin to allow TCP port
forwarding only two specific host/port pairs. Useful when combined
with Match.
If permitopen is used in both sshd_config and a key option, both
must allow a given connection before it will be permitted.
Note that users can still use external forwarders such as netcat,
so to be those must be controlled too for the limits to be effective.
Feedback & ok djm@, man page corrections & ok jmc@.
[clientloop.c ssh.1 ssh.c channels.c ssh_config.5 readconf.h session.c
channels.h readconf.c]
add ExitOnForwardFailure: terminate the connection if ssh(1)
cannot set up all requested dynamic, local, and remote port
forwardings. ok djm, dtucker, stevesk, jmc
[channels.c channels.h session.c]
make sure protocol messages for internal channels are ignored.
allow adjust messages for non-open channels; with and ok djm@
[auth-options.c auth-options.h channels.c channels.h clientloop.c]
[misc.c misc.h readconf.c readconf.h scp.c servconf.c servconf.h]
[serverloop.c sftp.c ssh.1 ssh.c ssh_config ssh_config.5 sshconnect.c]
[sshconnect.h sshd.8 sshd_config sshd_config.5]
Add support for tun(4) forwarding over OpenSSH, based on an idea and
initial channel code bits by markus@. This is a simple and easy way to
use OpenSSH for ad hoc virtual private network connections, e.g.
administrative tunnels or secure wireless access. It's based on a new
ssh channel and works similar to the existing TCP forwarding support,
except that it depends on the tun(4) network interface on both ends of
the connection for layer 2 or layer 3 tunneling. This diff also adds
support for LocalCommand in the ssh(1) client.
ok djm@, markus@, jmc@ (manpages), tested and discussed with others
[channels.c channels.h clientloop.c serverloop.c session.c]
fix regression I introduced in 4.2: X11 forwardings initiated after
a session has exited (e.g. "(sleep 5; xterm) &") would not start.
bz #1086 reported by t8m AT centrum.cz; ok markus@ dtucker@
- djm@cvs.openbsd.org 2005/07/17 06:49:04
[channels.c channels.h session.c session.h]
Fix a number of X11 forwarding channel leaks:
1. Refuse multiple X11 forwarding requests on the same session
2. Clean up all listeners after a single_connection X11 forward, not just
the one that made the single connection
3. Destroy X11 listeners when the session owning them goes away
testing and ok dtucker@
[channels.h]
race when efd gets closed while there is still buffered data:
change CHANNEL_EFD_OUTPUT_ACTIVE()
1) c->efd must always be valid AND
2a) no EOF has been seen OR
2b) there is buffered data
report, initial fix and testing Chuck Cranor
- djm@cvs.openbsd.org 2005/06/16 03:38:36
[channels.c channels.h clientloop.c clientloop.h ssh.c]
move x11_get_proto from ssh.c to clientloop.c, to make muliplexed xfwd
easier later; ok deraadt@
[auth-options.c channels.c channels.h clientloop.c compat.c compat.h]
[misc.c misc.h readconf.c readconf.h servconf.c ssh.1 ssh.c ssh_config.5]
[sshd_config.5]
bz#413: allow optional specification of bind address for port forwardings.
Patch originally by Dan Astorian, but worked on by several people
Adds GatewayPorts=clientspecified option on server to allow remote
forwards to bind to client-specified ports.
[channels.c channels.h clientloop.c]
fix some window size change bugs for multiplexed connections: windows sizes
were not being updated if they had changed after ~^Z suspends and SIGWINCH
was not being processed unless the first connection had requested a tty;
ok markus
[channels.c channels.h clientloop.c clientloop.h includes.h readconf.c]
[readconf.h scp.1 sftp.1 ssh.1 ssh.c ssh_config.5]
implement session multiplexing in the client (the server has supported
this since 2.0); ok markus@
[channels.c channels.h clientloop.c serverloop.c ssh.1]
bz #756: add support for the cancel-tcpip-forward request for the server and
the client (through the ~C commandline). reported by z3p AT twistedmatrix.com;
ok markus@
[channels.c channels.h session.c session.h]
display, screen, row, col, xpixel, ypixel are u_int; markus ok
- (bal) Also fixed IPADDR_IN_DISPLAY case where display, screen, row, col,
xpixel are u_int.
[channels.c channels.h compat.c compat.h nchan.c]
don't send stderr data after EOF, accept this from older known (broken)
sshd servers only, fixes http://bugzilla.mindrot.org/show_bug.cgi?id=179
Damien Miller
Darren Tucker
Ben Lindstrom