audk/MdeModulePkg/Bus/Pci/UhciDxe/UhciReg.h

247 lines
6.0 KiB
C
Raw Normal View History

/** @file
The definition for UHCI register operation routines.
Copyright (c) 2007 - 2008, Intel Corporation
All rights reserved. This program and the accompanying materials
are licensed and made available under the terms and conditions of the BSD License
which accompanies this distribution. The full text of the license may be found at
http://opensource.org/licenses/bsd-license.php
THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
**/
#ifndef _EFI_UHCI_REG_H_
#define _EFI_UHCI_REG_H_
typedef enum {
UHCI_FRAME_NUM = 1024,
//
// Register offset and PCI related staff
//
USB_BAR_INDEX = 4,
USBCMD_OFFSET = 0,
USBSTS_OFFSET = 2,
USBINTR_OFFSET = 4,
USBPORTSC_OFFSET = 0x10,
USB_FRAME_NO_OFFSET = 6,
USB_FRAME_BASE_OFFSET = 8,
USB_EMULATION_OFFSET = 0xC0,
//
// Packet IDs
//
SETUP_PACKET_ID = 0x2D,
INPUT_PACKET_ID = 0x69,
OUTPUT_PACKET_ID = 0xE1,
ERROR_PACKET_ID = 0x55,
//
// USB port status and control bit definition.
//
USBPORTSC_CCS = BIT0, // Current Connect Status
USBPORTSC_CSC = BIT1, // Connect Status Change
USBPORTSC_PED = BIT2, // Port Enable / Disable
USBPORTSC_PEDC = BIT3, // Port Enable / Disable Change
USBPORTSC_LSL = BIT4, // Line Status Low BIT
USBPORTSC_LSH = BIT5, // Line Status High BIT
USBPORTSC_RD = BIT6, // Resume Detect
USBPORTSC_LSDA = BIT8, // Low Speed Device Attached
USBPORTSC_PR = BIT9, // Port Reset
USBPORTSC_SUSP = BIT12, // Suspend
//
// UHCI Spec said it must implement 2 ports each host at least,
// and if more, check whether the bit7 of PORTSC is always 1.
// So here assume the max of port number each host is 16.
//
USB_MAX_ROOTHUB_PORT = 0x0F,
//
// Command register bit definitions
//
USBCMD_RS = BIT0, // Run/Stop
USBCMD_HCRESET = BIT1, // Host reset
USBCMD_GRESET = BIT2, // Global reset
USBCMD_EGSM = BIT3, // Global Suspend Mode
USBCMD_FGR = BIT4, // Force Global Resume
USBCMD_SWDBG = BIT5, // SW Debug mode
USBCMD_CF = BIT6, // Config Flag (sw only)
USBCMD_MAXP = BIT7, // Max Packet (0 = 32, 1 = 64)
//
// USB Status register bit definitions
//
USBSTS_USBINT = BIT0, // Interrupt due to IOC
USBSTS_ERROR = BIT1, // Interrupt due to error
USBSTS_RD = BIT2, // Resume Detect
USBSTS_HSE = BIT3, // Host System Error
USBSTS_HCPE = BIT4, // Host Controller Process Error
USBSTS_HCH = BIT5, // HC Halted
USBTD_ACTIVE = BIT7, // TD is still active
USBTD_STALLED = BIT6, // TD is stalled
USBTD_BUFFERR = BIT5, // Buffer underflow or overflow
USBTD_BABBLE = BIT4, // Babble condition
USBTD_NAK = BIT3, // NAK is received
USBTD_CRC = BIT2, // CRC/Time out error
USBTD_BITSTUFF = BIT1 // Bit stuff error
}UHCI_REGISTER_OFFSET;
/**
Read a UHCI register.
@param PciIo The EFI_PCI_IO_PROTOCOL to use.
@param Offset Register offset to USB_BAR_INDEX.
@return Content of register.
**/
UINT16
UhciReadReg (
IN EFI_PCI_IO_PROTOCOL *PciIo,
IN UINT32 Offset
);
/**
Write data to UHCI register.
@param PciIo The EFI_PCI_IO_PROTOCOL to use.
@param Offset Register offset to USB_BAR_INDEX.
@param Data Data to write.
@return None.
**/
VOID
UhciWriteReg (
IN EFI_PCI_IO_PROTOCOL *PciIo,
IN UINT32 Offset,
IN UINT16 Data
);
/**
Set a bit of the UHCI Register.
@param PciIo The EFI_PCI_IO_PROTOCOL to use.
@param Offset Register offset to USB_BAR_INDEX.
@param Bit The bit to set.
@return None.
**/
VOID
UhciSetRegBit (
IN EFI_PCI_IO_PROTOCOL *PciIo,
IN UINT32 Offset,
IN UINT16 Bit
);
/**
Clear a bit of the UHCI Register.
@param PciIo The PCI_IO protocol to access the PCI.
@param Offset Register offset to USB_BAR_INDEX.
@param Bit The bit to clear.
@return None.
**/
VOID
UhciClearRegBit (
IN EFI_PCI_IO_PROTOCOL *PciIo,
IN UINT32 Offset,
IN UINT16 Bit
);
/**
Clear all the interrutp status bits, these bits
are Write-Clean.
@param Uhc The UHCI device.
@return None.
**/
VOID
UhciAckAllInterrupt (
IN USB_HC_DEV *Uhc
);
/**
Stop the host controller.
@param Uhc The UHCI device.
@param Timeout Max time allowed.
@retval EFI_SUCCESS The host controller is stopped.
@retval EFI_TIMEOUT Failed to stop the host controller.
**/
EFI_STATUS
UhciStopHc (
IN USB_HC_DEV *Uhc,
IN UINTN Timeout
);
/**
Check whether the host controller operates well.
@param PciIo The PCI_IO protocol to use.
@retval TRUE Host controller is working.
@retval FALSE Host controller is halted or system error.
**/
BOOLEAN
UhciIsHcWorking (
IN EFI_PCI_IO_PROTOCOL *PciIo
);
/**
Set the UHCI frame list base address. It can't use
UhciWriteReg which access memory in UINT16.
@param PciIo The EFI_PCI_IO_PROTOCOL to use.
@param Addr Address to set.
@return None.
**/
VOID
UhciSetFrameListBaseAddr (
IN EFI_PCI_IO_PROTOCOL *PciIo,
IN VOID *Addr
);
/**
Disable USB Emulation.
@param PciIo The EFI_PCI_IO_PROTOCOL protocol to use.
@return None.
**/
VOID
UhciTurnOffUsbEmulation (
IN EFI_PCI_IO_PROTOCOL *PciIo
);
#endif