Today's McaInitialize() doesn't check State value before initialize
MCi_CTL and MCi_STATUS.
The patch fixes this issue by only initializing the two kinds of
MSRs when State is enabled.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Today's implementation only assumes SandyBridge CPU supports
Extended On-Demand Clock Modulation Duty Cycle.
Actually it is supported when CPUID.06h.EAX[5] == 1.
When platform requests 50% throttling, it causes value 1000b
set to the low-4 bits of IA32_CLOCK_MODULATION.
But the wrong code sets 1000b to bits[1-3] which causes assertion.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <vanjeff_919@hotmail.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
The reason doing this is that we found that calling StartupAllAps() to
flush TLB for all APs in CpuDxe driver after changing page attributes
will spend a lot of time to complete. If there are many page attributes
update requests, the whole system performance will be slowed down
explicitly, including any shell command and UI operation.
The solution is removing the flush operation for AP in CpuDxe driver.
Since TLB is always flushed in HLT loop mode, we just need to enforce
a TLB flush for mwait loop mode.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
This issue is introduced by a patch at
f32bfe6d06
The above patch miss the case of 64-bit PEI, which will link
X64/MpFuncs.nasm instead of Ia32/MpFuncs.nasm. For X64/MpFuncs.nasm,
ExchangeInfo->ModeHighMemory should be always initialized no matter
if separate wakeup buffer is allocated or not. Ia32/MpFuncs.nasm will
not need ModeHighMemory during AP init. So the changes made in this
patch should not affect the functionality of it.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Every processor's StartupApSignal is initialized in
MpInitLibInitialize() before calling CollectProcessorCount().
When SortApicId() is called from CollectProcessorCount(), AP Index
is re-assigned by APIC ID. But SortApicId() forgets to set the
correct StartupApSignal when sorting the AP.
The patch fixes this issue.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Chasel Chiu <chasel.chiu@intel.com>
To fix an issue in which enabling NX feature will mark the AP wakeup
buffer as non-executable and fail the AP init, the buffer was split
into two part: the lower part in memory within 1MB and the higher part
within allocated executable memory (EfiBootServicesCode). But the
address of higher part memory was stored in lower part memory, which
is actually shared with legacy components and will be overwritten by
LegacyBiosDxe driver if CSM is enabled.
This patch fixes this issue by storing the address of higher part
memory in CpuMpData instead of ExchangeInfo.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
MtrrSetMemoryAttributesInMtrrSettings() is a batch-set API.
When setting multiple ranges of memory attributes, the single-set
API (MtrrSetMemoryAttributeInMtrrSettings and MtrrSetMemoryAttribute)
may fail, but batch-set API may succeed.
Add comments to recommend caller to use batch-set API when setting
multiple ranges.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Ming Shao <ming.shao@intel.com>
GetWakeupBuffer() tries to find a below-1M free memory, it checks
whether the memory is allocated already in
CheckOverlapWithAllocatedBuffer(). When there is a memory allocation
hob (base = 0xff_00000000, size = 0x10000000),
CheckOverlapWithAllocateBuffer() truncates the base to 0 which causes
it always returns TRUE so GetWakeupBuffer() fails to find a below-1MB
memory.
The patch fixes this issue by using UINT64 type.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jeff Fan <vanjeff_919@hotmail.com>
If PcdDxeNxMemoryProtectionPolicy is set to enable protection for memory
of EfiBootServicesData, EfiConventionalMemory, the BIOS will reset after
timer initialized and started.
The root cause is that the memory used to hold the exception and interrupt
handler is allocated with type of EfiBootServicesData and marked as
non-executable due to NX feature enabled. This patch fixes it by allocating
EfiBootServicesCode type of memory for those handlers instead.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
If PcdDxeNxMemoryProtectionPolicy is set to enable protection for memory
of EfiBootServicesCode, EfiConventionalMemory, the BIOS will hang at a page
fault exception during MP initialization.
The root cause is that the AP wake up buffer, which is below 1MB and used
to hold both AP init code and data, is type of EfiConventionalMemory (not
really allocated because of potential conflict with legacy code), and is
marked as non-executable. During the transition from real address mode
to long mode, the AP init code has to enable paging which will then cause
itself a page fault exception because it's just running in non-executable
memory.
The solution is splitting AP wake up buffer into two part: lower part is
still below 1MB and shared with legacy system, higher part is really
allocated memory of BootServicesCode type. The init code in the memory
below 1MB will not enable paging but just switch to protected mode and
jump to higher memory, in which the init code will enable paging and
switch to long mode.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Commits a2ea6894e6
* UefiCpuPkg/MpInitLib: Fix a bug that AP enters timer INT handler
masked the interrupts in AP.
But it didn't unmask the interrupt in new BSP when Switch BSP
happens.
The patch fixed this issue.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jeff Fan <vanjeff_919@hotmail.com>
Cc: Eric Dong <eric.dong@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=849
In V2, use "mov rax, strict qword 0" to replace the hard code db.
1. Use lea instruction to get the address instead of mov instruction.
2. Use the dummy address as jmp destination, and add the logic to fix up
the address to the absolute address at boot time.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Liming Gao <liming.gao@intel.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=849
In V2, use mov rax, strict qword 0 to replace the hard code db.
Use the dummy address as jmp destination, and add the logic to fix up
the address to the absolute address at boot time.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Liming Gao <liming.gao@intel.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Enhance MCA feature dependency check base on SDM pseudocode example 15-1.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Bell Song <binx.song@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
0 40 f0 100
+---WT--+--UC--+--WT--+-----WB----+----UC----+
When calculating the shortest path from 0 to 100, the
MtrrLibCalculateLeastMtrrs() is called to update the
Vertices.Previous.
When calculating the shortest path from 0 to 40,
MtrrLibCalculateLeastMtrrs() is called recursively to update the
Vertices.Previous.
The second call corrupt the Previous value that will be used
later.
The patch removes the code that corrupts Previous.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
80 A8 B0 B8 C0
+----------WB--------+-UC-+-WT-+-WB-+
For above memory settings, current code caused the final MTRR
settings miss [A8, B0, UC] when default memory type is UC.
The root cause is the code only checks the mandatory weight
between A8 to B0, but skips to check the optional weight.
The patch fixes this issue.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
The patch only change the comments and variable name so
doesn't impact the functionality.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
*SetMemoryAttribute*() API cannot handle the setting request that
looks like <0, MAX_ADDRESS, Type>. The buggy parameter checking
logic returns Unsupported for this case.
The patch fixes the checking logic to handle such case.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Code forgot to initialize the optional weight between adjacent
vertices. It caused wrong MTRR result was calculated for some
memory settings.
The logic was incorrectly removed when converting from POC
code. The patch adds back the initialization.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
MtrrSetMemoryAttributesInMtrrSettings() missed the debug messages
of memory attribute request and status. The patch moves all debug
messages from MtrrSetMemoryAttributeInMtrrSettings() to
MtrrSetMemoryAttributesInMtrrSettings() and refines the debug message
to carry more information.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
The reason is that DXE part initialization will reuse the stack allocated
at PEI phase, if MP was initialized before. Some code added to check this
situation and use stack base address saved in HOB passed from PEI.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
As the name suggests, CpuMpData->CpuInfoInHob[0].ApTopOfStack must be init
to the top of stack. But the MpInitLibInitialize() passed the base address
of stack to InitializeApData(), which is not correct. Although this stack
is not used for BSP, it's should be fixed in case of misunderstanding and
future possible code changes.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
When SourceLevelDebug is enabled, AP randomly executes the DXECORE
timer handler logic. The root cause is the interrupts are not
masked in AP wake up procedure.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jeff Fan <vanjeff_919@hotmail.com>
Enhance DumpModuleImageInfo() for page fault with I/D set.
If it is page fault with I/D set, the (E/R)IP in SystemContext
could not be used for DumpModuleImageInfo(), instead of, the next
IP of the IP triggering this page fault could be found from stack
by (E/R)SP in SystemContext.
IA32 SDM:
— I/D flag (bit 4).
This flag is 1 if the access causing the page-fault exception was
an instruction fetch. This flag describes the access causing the
page-fault exception, not the access rights specified by paging.
The idea comes from SmiPFHandler () in
UefiCpuPkg/PiSmmCpuDxeSmm/Ia32/PageTbl.c and
UefiCpuPkg/PiSmmCpuDxeSmm/X64/PageTbl.c.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Fix comment typo for MtrrLibApplyFixedMtrrs function
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Bell Song <binx.song@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Roll back commit 56649f4301.
The original names follows the spec definition.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
With correct model CPU, current checking logic will
always execute AsmReadMsr64 operation and then check
ECX.AESNI[bit 25] = 1. Update checking logic to check
ECX.AESNI[bit 25] = 1 first and then do AsmReadMsr64
operation.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Bell Song <binx.song@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
When CpuCommonFeaturesLib use RegisterCpuFeaturesLib to register
CPU features, the CpuFeaturesData->BitMaskSize has already been
initialized. So delete redundant PcdGetSize PcdCpuFeaturesSupport
in CpuInitDataInitialize.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Bell Song <binx.song@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
This reverts commit 5c59537c10.
Current code already has function IsCpuFeatureSupported to do
the feature validation, not need this check logic anymore.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Bell Song <binx.song@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Due to coding style fix of the structure definition in BaseLib.h, all
code referencing those structure must be updated accordingly.
Cc: Dandan Bi <dandan.bi@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Dandan Bi <dandan.bi@intel.com>
AP has its own stack for code execution. If PcdCpuStackGuard is enabled,
the page at the bottom of stack of AP will be disabled (NOT PRESENT) to
monitor the stack overflow issue. This requires PcdCpuApStackSize to be
set with value more than one page of memory.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Change GetSupportPcds and GetConfigurationPcds to be singular
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Bell Song <binx.song@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
V2:
Update function name, add more detail description.
V1:
Check and assert invalid RegisterCpuFeature function parameter
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Bell Song <binx.song@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
When printing the ascii format of memory attribute in debug message,
%s was used, but %a should be used.
The patch additionally changes %x to %r for EFI_STATUS.
The whole patch doesn't impact functionality of the MtrrLib.
Just debug message fix.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Ming Shao <ming.shao@intel.com>
In current implementation of CPU MP service, AP is initialized with data
copied from BSP. Stack switch required by Stack Guard feature needs different
GDT, IDT table and task gates for each logic processor. This patch adds GDTR,
IDTR and TR into structure CPU_VOLATILE_REGISTERS and related code in save
and restore methods. This can make sure that any changes to GDT, IDT and task
gate for an AP will be kept from overwritten by BSP settings.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Suggested-by: Ayellet Wolman <ayellet.wolman@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Jeff Fan <vanjeff_919@hotmail.com>
Reviewed-by: Jiewen.yao@intel.com
If Stack Guard is enabled and there's really a stack overflow happened during
boot, a Page Fault exception will be triggered. Because the stack is out of
usage, the exception handler, which shares the stack with normal UEFI driver,
cannot be executed and cannot dump the processor information.
Without those information, it's very difficult for the BIOS developers locate
the root cause of stack overflow. And without a workable stack, the developer
cannot event use single step to debug the UEFI driver with JTAG debugger.
In order to make sure the exception handler to execute normally after stack
overflow. We need separate stacks for exception handlers in case of unusable
stack.
IA processor allows to switch to a new stack during handling interrupt and
exception. But X64 and IA32 provides different ways to make it. X64 provides
interrupt stack table (IST) to allow maximum 7 different exceptions to have
new stack for its handler. IA32 doesn't have IST mechanism and can only use
task gate to do it since task switch allows to load a new stack through its
task-state segment (TSS).
The new API, InitializeCpuExceptionHandlersEx, is implemented to complete
extra initialization for stack switch of exception handler. Since setting
up stack switch needs allocating new memory for new stack, new GDT table
and task-state segment but the initialization method will be called in
different phases which have no consistent way to reserve those memory, this
new API is allowed to pass the reserved resources to complete the extra
works. This is cannot be done by original InitializeCpuExceptionHandlers.
Considering exception handler initialization for MP situation, this new API
is also necessary, because AP is not supposed to allocate memory. So the
memory needed for stack switch have to be reserved in BSP before waking up
AP and then pass them to InitializeCpuExceptionHandlersEx afterwards.
Since Stack Guard feature is available only for DXE phase at this time, the
new API is fully implemented for DXE only. Other phases implement a dummy
one which just calls InitializeCpuExceptionHandlers().
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Suggested-by: Ayellet Wolman <ayellet.wolman@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Jeff Fan <vanjeff_919@hotmail.com>
Reviewed-by: Jiewen.yao@intel.com
For some special platforms (such as Ovmf), it is possible
that, some APs start up *and finish* before the remaining
APs start up *at all*. In this case, the enhance
solution by changes 0594ec41 not works as expected.
This change remove check CpuMpData->CpuCount logic to let old
solution still workable if platform owner still set a long
time for PcdCpuApInitTimeOutInMicroSeconds. It's platform
owner's response to decide which solution to use.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Jeff Fan <vanjeff_919@hotmail.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <vanjeff_919@hotmail.com>
Current logic always waiting for a specific value to collect all APs
count. This logic may caused some platforms cost too much time to
wait for time out.
This patch add new logic to collect APs count. It adds new variable
NumApsExecuting to detect whether all APs have finished initialization.
Each AP let NumApsExecuting++ when begin to initialize itself and let
NumApsExecuting-- when it finish the initialization. BSP base on whether
NumApsExecuting == 0 to finished the collect AP process.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jeff Fan <vanjeff_919@hotmail.com>
Original AP index variable name not well express the meaning
of the variable. Also this name is better used in later patch.
So change the variable name for better understanding.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jeff Fan <vanjeff_919@hotmail.com>
ClearMasks and OrMasks are not 8-byte aligned.
But SetMem64 requires the input address is 8-byte aligned.
If the input is not 8-byte aligned, assertion is hit.
Use SetMem instead.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
MtrrLibSetBelow1MBMemoryAttribute() may be called multiple times.
It's possible that in a 2nd call, Modified[0] is set to TRUE in
1st call but ClearMasks[0] and OrMasks[0] is uninitialized in
2nd call. It causes FixedSettings->Mtrr[0] be set to random
data.
The patch fixes this issue by introducing a local Modified[]
array and only updates FixedSettings->Mtrr[] when LocalModified[i]
is TRUE.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
MicrocodeDetect function will run by every threads, and it will
use PcdGet to get PcdCpuMicrocodePatchAddress and
PcdCpuMicrocodePatchRegionSize, if change both PCD default to dynamic,
system will in non-deterministic behavior.
By design, UEFI/PI services are single threaded and not re-entrant
so Multi processor code should not use UEFI/PI services. Here, Pcd
protocol/PPI is used to access dynamic PCDs so it would result in
non-deterministic behavior.
This code get PCD value in BSP and save them in CPU_MP_DATA for Ap.
https://bugzilla.tianocore.org/show_bug.cgi?id=726
Cc: Crystal Lee <CrystalLee@ami.com.tw>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
ARRAY_SIZE(Mtrrs->Variables.Mtrr) was used in
MtrrDebugPrintAllMtrrsWorker() to parse the MTRR registers.
Instead, the actual variable MTRR count should be used.
Otherwise, the uninitialized random data in MtrrSetting may cause
MtrrLibSetMemoryType() hang.
Steven Shi found this bug in QEMU when using Q35 chip.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Steven Shi <steven.shi@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
The patch optimized the MTRR access code to skip the Base MSR
access when the Mask MSR indicates the pair is invalid.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Ruiyu Ni
Jian J Wang
Star Zeng
Liming Gao
Song, BinX
Eric Dong
Dandan Bi