Previously, the SMM S3 resume code required taking control of APs to
perform SMM rebase, which would overwrite the context set by MpLib.
As a result, MpLib needed to wake up APs using InitSipiSipi to restore
the context after SMM S3 resume.
With the recent change where SMM rebase occurs in the early PEI phase,
the SMM S3 resume code no longer modifies AP context. Therefore, the
forced use of InitSipiSipi after SMM S3 resume is no longer necessary.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
The OpenSSL library uses floating point registers.
The is no guarantee that a prior firmware stage has enabled the FPU.
Provide a library BaseRiscVFpuLib to
* Enable the FPU and set it to state 'dirty'.
* Clear the fcsr CSR.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Currently, TDX exposes MTRR CPUID bit to TDX VM. So based on the CPUID,
the guest software components (OVMF/TDVF and guest kernel) will access
MTRR MSRs. One problem for guest to use of MTRR is the change of MTRR
setting needs to set CR0.CD=1, which will case #VE for TDX.
For Linux kernel, there is a mechanism called SW defined MTRR introduced
by the patch https://lore.kernel.org/all/20230502120931.
20719-4-jgross@suse.com/. If this is integrated for TDX guest, then Linux
kernel will not access any MTRR MSRs.
So we update MtrrLibIsMtrrSupported() to always return false for TD-Guest,
then TDVF will not access MTRR MSRs at all.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Binbin Wu <binbin.wu@intel.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
This patch is to avoid configure SMBASE if SmBase relocation has been
done. If gSmmBaseHobGuid found, means SmBase info has been relocated
and recorded in the SmBase array. No need to do the relocation in
SmmCpuFeaturesInitializeProcessor().
Signed-off-by: Phil Noh <Phil.Noh@amd.com>
Since the LoongArch SPEC has adjusted the CSR 0x20 register name and
the MdePkg also added the new name, so enable it in UefiCpuPkg.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Signed-off-by: Chao Li <lichao@loongson.cn>
The BSP's APIC mode is synced to all APs in CollectProcessorCount().
So, it's safe to skip the X2 APIC enabling in AutoEnableX2Apic() which
runs later when BSP's APIC mode is X2 APIC already.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
The change saves the BSP's initial APIC mode and syncs to all APs
in first time wakeup. It allows certain platforms to switch to X2 APIC
as early as possible and also independent on CpuFeaturePei/Dxe.
The platform should switch BSP to X2 APIC mode first before the
CpuMpPeim runs.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
It's very confusing that auto X2 APIC enabling and APIC ID sorting
are all performed inside CollectProcessorCount().
The change is to separate the X2 APIC enabling to AutoEnableX2Apic()
and call that from MpInitLibInitialize().
SortApicId() is called from MpInitLibInitialize() as well.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
This library provides an interface to request non-MMRAM pages to be
mapped/unblocked from inside MM environment.
For MM modules that need to access areas outside of
MMRAMs, the agents responsible for setting up these regions must use
this API to enable access to these memory areas from within MM. During
the IPL, when RestrictedMemoryAccess is enabled,
this unblocked memory is specifically used to create a BuildResourceHob,
which allocates storage for the SMM accessible DRAM (non-MMIO) range.
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Sami Mujawar <sami.mujawar@arm.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Hongbin1 Zhang <hongbin1.zhang@intel.com>
Cc: Wei6 Xu <wei6.xu@intel.com>
Cc: Dun Tan <dun.tan@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Commit 2f499c36db commented out the
RandomTestCase tests in CpuPageTableLibTestHost, but it left the
test suite being registered without any tests. This causes a failure
for tools that check to ensure tests are being registered with test
suites.
This patch comments out the test suite in addition to the tests
being added to it.
Signed-off-by: Oliver Smith-Denny <osde@linux.microsoft.com>
Structure assignment may depend on the compiler to expand to memcpy.
For this, we may need to add -mno-memcpy to the compilation flag.
Here, we reduce dependencies and use CopyMem for data conversion without
memcpy.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Cc: Chao Li <lichao@loongson.cn>
Signed-off-by: Dongyan Qian <qiandongyan@loongson.cn>
Co-authored-by: Chao Li <lichao@loongson.cn>
Given that the second parameter can be universally set to TRUE across
all use cases, its removal simplifies the function interface and the
associated code paths.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Analysis of the current usage patterns revealed that this parameter
should consistently set to TRUE.
Specifically, the parameter was found to be False in the following
scenarios:
1. During the initial volatile register setup for the first AP wake-up
in both the PEI and DXE phases. In these instances, the volatile
registers are pre-initialized in MpInitLibInitialize(),
and manually setting them to zero does not require altering the DR
state.
2. When switching the BSP, the new BSP does not synchronize the DR.
This behavior is now adjusted to ensure the DR state is synchronized,
aligning with a more logical and expected behavior when transitioning
BSP roles.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
In previoud commit, we remove the ApInitReconfig status. Now there
are only two status ApInitConfig and ApInitDone.
Only the very first waking up AP needs to set ApInitConfig status.
Therefore, if this is not the first wake up, set ApInitDone status
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
ApInitReconfig status is used to indicate that when AP wakes up, AP
need to restore volatile registers from BSP and use InitSipiSipi. Since
we handle the volatile registers well, we can use WakeUpByInitSipiSipi
flag to replace ApInitReconfig. Avoid using ApInitReconfig can simplify
code.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
When enable stack guard, APs needs separate GDTs.
In current code, APs will lose their separate GDTs when AP get disabled
and later re-enabled. This is because when re-enabling AP, AP restores
volatile registers from BSP.
This patch updates the AP management to ensure that each AP saves and
restores its own set of volatile registers to solve this issue.
Key changes include:
- APs now maintain their own volatile register space, eliminating
dependency on the BSP's register state.
- Special handling is implemented for the first AP wake-up during the
PEI and DXE phases, where the volatile registers are synchronized from
the BSP.
- When switching BSP, remove manual handling the global variable
CpuMpData->CpuData[Index].VolatileRegisters. The manually handling
in previous code is because, old BSP may not save volatile registers
after the AP procedure and new BSP's VolatileRegisters buffer may be
used by other APs. Now, since AP always save/restore volatile registers
from their own buffer, no need to do the special handling.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
BSP should save and sync to AP the init timer count instead of
current timer count.
Also, BSP can check the init timer count to know if the local apic
timer is enabled. Only sync the setting when it is enabled.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
This update ensures the consistency of Local APIC timer settings across
all processors when a BSP switch occurs.
The Local APIC timer is utilized in two distinct scenarios:
1. As a delay mechanism within the timer library.
2. To generate periodic timer interrupts during the DXE phase.
For scenario 1, APs can simply inherit the initial settings from the
BSP. Even the local APIC timer setting is changed by BSP later, AP
can still use the old setting. Therefore, the code to save the Local
APIC timer can be moved to MpInitLibInitialize().
For scenario 2, because normal AP doesn't enable timer interrupt, we
only need to care SwitchBsp case. It is crucial that the periodic
timer interrupts remain operational after BSP is switched. To achieve
this, the Local APIC timer settings on old BSP are now preserved and
synced to new BSP.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
CPU_AP_DATA contains AP's information such as CpuHealthy and
VolatileRegisters. Exchange the whole CPU_AP_DATA buffer instead
some fields to make code more simple.
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
CONFIDENTIAL_COMPUTING_GUEST_ATTR is not a simple SEV level anymore
and includes a feature mask since the previous commit.
Fix AmdMemEncryptionAttrCheck to check the level and feature
correctly and add DebugVirtualization support.
Since the actual feature flag is not set yet, this should cause
no behavioural change.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Alexey Kardashevskiy <aik@amd.com>
---
Changes:
v5:
* "rb" from Tom
On the LoongArch platform:
the a0 register can be used as both a function parameter and a return value.
Due to parameter EFI_SYSTEM_CONTEXT being overwritten by an invalid context address,
when calling GetExceptionType, incorrect parameter address causes memory access exception.
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4796
Cc: Chao Li <lichao@loongson.cn>
Signed-off-by: Dongyan Qian <qiandongyan@loongson.cn>
This patch fixes an error in calculating cache sizes for cores from
different Dies. The original code incorrectly cleared cache sizes for
different core types during intermediate calculation steps, leading to
mistakes in counting duplicate entries. This patch adds a check for
cache size to distinguish between different cache types.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: xieyuanh <yuanhao.xie@intel.com>
Update reference to SevSnpMsr.h as part of a refactor of MSR definitions and
SEV-SNP related defines. Remove family-specific references (filename) as these
defines are common to all modern EPYC Processors.
Signed-off-by: Paul Grimes <paul.grimes@amd.com>
Declares in the .inf file that the current component is an MM_STANDALONE
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
This patch is to fix issue when splitting leaf paging
entry in CpuPageTableLib code.
In previous code, before we assign the new child paging
structure address to the content of splitted paging entry,
PageTableLibSetPnle() is called to make sure the bit7 is
set to 0, which indicate the previous leaf entry is
changed to non-leaf entry now. There is a gap between
we change the bit7 and we assign the new child paging
structure address to the content of the splitted paging
entry. If the address of code execution or data access
happens to be in the range covered by the splitted paging
entry, this gap may cause issue.
In this patch, we prepare the new paging entry content
value in a local variable and assign the value to the
splitted paging entry at once. The volatile keyword
is used to ensure that no optimization will occur in
compilation.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Cc: Zhou Jianfeng <jianfeng.zhou@intel.com>
In this commit, change PeiMpLib to install callback
of gEdkiiEndOfS3ResumeGuid to relocate AP to new safe
buffer. The gEdkiiEndOfS3ResumeGuid is installed in
S3Resume.c before jmping to OS waking vector.
Previously, code in CpuS3.c of PiSmmCpuDxe driver will
prepare the new safe buffer for AP and place AP in hlt
loop state. With this code change, we can remove the
Machine Instructions of mApHltLoopCode in PiSmmCpuDxe.
Also we can reuse the related code in DxeMpLib for
PeiMpLib.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Move some code in DxeMpLib.C to common MpLib.c.
The related code is to relocate Ap to new safe buffer
before booting into OS. In next commits, these code
also will be used by PeiMpLib. This commit doesn't
change any code functionality.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Abstract some DxeMpLib code to function in this commit.
Some of these internal functions will be moved to common
MpLib.c in following commits. Then PeiMpLib can reuse
the code.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Disable paging in IA32 RelocateApLoop assembly
code to fix the issue that the AP page table is
unavailiable after boot OS under IA32 execution mode.
This issue exist in IA32 PEI + IA32 DXE normal boot
(also S3 boot with IA32 PEI after previous three commits
are accepted). In current MpLib code, the IA32 execution
mode code did not create page table in reserved memory
like what X64 code did. If PcdCpuStackGuard is TRUE, the
PG is enabled for AP in current RelocateApLoop assembly
code. And the page table for AP is unavailiable after
boot OS. This might cause potential issue. So disable PG
in IA32 RelocateApLoop.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=4778
MPInitlib have wrong expectation that BSP index should always be 0 in
MpInitLibInitialize(), SwitchBsp(),ApWakeupFunction().
That will cause the data mismatch, if the initial BSP is not 0.
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Ning Feng <ning.feng@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Intel has some features need to use processor extended
information under CPU feature InitializeFunc(), so add code
to support it: This patch is to add CPU_V2_EXTENDED_TOPOLOGY
to get processor extended info.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Zeng Star <star.zeng@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Due to the definition difference of SMRAM Save State,
SmmBase config in SMRAM Save State for AMD is also different.
This patch provides the AmdSmmRelocationLib library instance
to handle the SMRAM Save State difference.
Cc: Abdul Lateef Attar <AbdulLateef.Attar@amd.com>
Cc: Abner Chang <abner.chang@amd.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Zeng Star <star.zeng@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Acked-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Abdul Lateef Attar <AbdulLateef.Attar@amd.com>
This patch is to remove unnecessary CpuIndex.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Zeng Star <star.zeng@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
This patch aims on mProcessorInfo global variable, which can be
defined as local variable in SmmRelocateBases(). With this patch,
no need to allocate the memory for all CPUs to store the
Processor Info.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Zeng Star <star.zeng@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Since SMM relocation is performed serially for each CPU, there is
no need to allocate buffers for all CPUs to store the SmBase
address in mSmBase and the Rebased flag in mRebased. A defined
global variable is sufficient.
This patch focuses on the mSmBase and mRebased global variables
to prevent unnecessary memory allocation for these variables.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Zeng Star <star.zeng@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
This patch aims to rename global variables for clearer
association with Smm Init, ensuring their names are
distinct from those used in the PiSmmCpuDxeSmm Driver.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Zeng Star <star.zeng@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
This patch just separates the smbase relocation logic from
PiSmmCpuDxeSmm driver, and moves to the SmmRelocationInit
interface. It maintains the original implementation of most
functions and leaves the definitions of global variables
intact. Further refinements to the code are planned for
subsequent patches.
Platform shall consume the interface for the smbase
relocation if need SMM support.
Note:
Before using SmmRelocationLib, the PiSmmCpuDxeSmm driver
allocates the SMRAM to be used for SMI handler and Save
state area of each processor from Smst->AllocatePages().
With SmmRelocationLib, the SMRAM allocation for SMI
handlers and Save state areas is moved to early PEI
phase (Smst->AllocatePages() service is not available).
So, the allocation is done by splitting the SMRAM out of
the SMRAM regions reported from gEfiSmmSMramMemoryGuid.
So, Platform must produce the gEfiSmmSMramMemoryGuid HOB
for SmmRelocationLib usage.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Zeng Star <star.zeng@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
ProcessorNumber 0 is not always BSP. Debug message based on 0
of ProcessorNumber is incorrect.
This patch is to clean the debug message in LmceSupport
directly.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Zeng Star <star.zeng@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Zeng Star <star.zeng@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4654
When running under an SVSM, the VMPL level of the APs that are started
must match the VMPL level provided by the SVSM. Additionally, each AP
must have a Calling Area for use with the SVSM protocol. Update the AP
creation to properly support running under an SVSM.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Acked-by: Ray Ni <ray.ni@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4654
The RMPADJUST instruction is used to change the VMSA attribute of a page,
but the VMSA attribute can only be changed when running at VMPL0. To
prepare for running at a less priviledged VMPL, use the AmdSvsmLib library
API to perform the RMPADJUST. The AmdSvsmLib library will perform the
proper operation on behalf of the caller.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4654
In order to support an SEV-SNP guest running under an SVSM at VMPL1 or
lower, a new library must be created.
This library includes an interface to detect if running under an SVSM, an
interface to return the current VMPL, an interface to perform memory
validation and an interface to set or clear the attribute that allows a
page to be used as a VMSA.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4654
Currently, the first time an AP is started for an SEV-SNP guest, it relies
on the VMSA as set by the hypervisor. If the list of APIC IDs has been
retrieved, this is not necessary. The list of APIC IDs will be identified
by a GUIDed HOB. If the GUIDed HOB is present, use the SEV-SNP AP Create
protocol to start the AP for the first time and each time thereafter.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Ray Ni <ray.ni@intel.com>
Add a new base library named CpuMmuLib and add a LoongArch64 instance
with in the library.
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4734
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Chao Li <lichao@loongson.cn>
Co-authored-by: Baoqi Zhang <zhangbaoqi@loongson.cn>
Co-authored-by: Dongyan Qian <qiandongyan@loongson.cn>
Co-authored-by: Xianglai Li <lixianglai@loongson.cn>
Co-authored-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Ray Ni <ray.ni@intel.com>
Add the LoongArch64 CPU Timer instance to CpuTimerLib, using CPUCFG 0x4
and 0x5 for Stable Counter frequency.
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4734
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Chao Li <lichao@loongson.cn>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Some of the order is not in alphabetical, reorder.
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4726
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Chao Li <lichao@loongson.cn>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Some of the order is not in alphabetical, reorder.
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4726
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Chao Li <lichao@loongson.cn>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Zhiguang Liu
Heinrich Schuchardt
Min M Xu
Phil Noh
Chao Li
Ray Ni
xieyuanh
Oliver Smith-Denny
Dongyan Qian
Alexey Kardashevskiy
Jiaxin Wu
Paul Grimes
Dun Tan
Ning Feng
Tom Lendacky