1. Boost IDE mode boot when slave device is absent.
2. Use D2H FIS to check if the PIO OUT/DMA IN/DMA OUT transfer is finished or error happened. ATA PIO IN has special check as it may just receive PIO SETUP FIS for success case.
3. Add command status register check for IDE DMA transfer.
4. ScsiDiskReadCapacity() in ScsiDisk should return EFI_SUCCESS if SENSE Data request is success.
Signed-off-by: erictian
Reviewed-by: rsun3
Reviewed-by: xdu2
Reviewed-by: mdkinney
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12658 6f19259b-4bc3-4df7-8a09-765794883524
0. Remove the unused private GUID from module source files.
1. Use gEfiCallerIdGuid replace of the private module GUID.
2. Add the public header files to define HII FormSet and PackageList GUID used in every HII driver.
3. Move two EBC protocols for debug purpose from EBC driver to MdeModulePkg Include directory.
Signed-off-by: lgao4
Reviewed-by: ydong10 gdong1 tye jfan12 wli12 rsun3 jyao1
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12373 6f19259b-4bc3-4df7-8a09-765794883524
SCSI Interface GUID: Physical SCSI disk
IDE Interface GUID: ATAPI device run in legacy IDE mode
AHCI Interface GUID: ATAPI device run in AHCI mode.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9584 6f19259b-4bc3-4df7-8a09-765794883524
a. Add check validation of RemainingDevicePath in Supported()
b. In Star() function, if RemaingDevicePath is the End of Device Path Node, don't create child device and return EFI_SUCCESS.
2. fixed one device path issue in ScsiBus driver.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9264 6f19259b-4bc3-4df7-8a09-765794883524
The others changes include:
1. Check RemainingDevicePath at beginning of Supported(), make sure it has been verified before Start() is called.
2. Check IO protocol firstly rather than EfiDevicePathProtocolGuid, reduce the times entering into Start() function because EfiDevicePathProtocolGuid existed on most of handle.
3. If no any child device is created on last time, and RemainingDevicePath is valid Uart Devcie path, go on creating child device handle based on this RemainingDevicePath.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9262 6f19259b-4bc3-4df7-8a09-765794883524
///
/// Standard INQUIRY data format
///
typedef struct {
UINT8 Peripheral_Type : 5;
UINT8 Peripheral_Qualifier : 3;
UINT8 DeviceType_Modifier : 7;
UINT8 Rmb : 1;
UINT8 Version;
UINT8 Response_Data_Format;
UINT8 Addnl_Length;
UINT8 Reserved_5_95[95 - 5 + 1];
} EFI_SCSI_INQUIRY_DATA;
is longer than 36 bytes and EFI_BAD_BUFFER_SIZE may be returned if the actual inquiry data is less than that of EFI_SCSI_INQUIRY_DATA.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@8329 6f19259b-4bc3-4df7-8a09-765794883524
Our UEFI Driver supports both SCSI Passthru (SPT) and Ext SCSI Passthru (That is our driver installs both SCSI Passthru and Ext SCSI Passthru). When we unload our driver SCSI Bus driver closes only ESPT and keeps SPT open. Due to this when I load my driver second time the SPT installation will fail and now attempting to unload will either crash the system or hang the system.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@7906 6f19259b-4bc3-4df7-8a09-765794883524
EFI_SIGNATURE_16 -> SIGNATURE_16
EFI_SIGNATURE_32 -> SIGNATURE_32
EFI_SIGNATURE_64 -> SIGNATURE_64
EFI_FIELD_OFFSET -> OFFSET_OF
EFI_MAX_BIT -> MAX_BIT
EFI_MAX_ADDRESS -> MAX_ADDRESS
These macros are not defined in UEFI spec. It makes more sense to use the equivalent macros in Base.h to avoid alias.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@7056 6f19259b-4bc3-4df7-8a09-765794883524
erictian
lgao4
niruiyu
ydong10
li-elvin
hhtian
rsun3
davidhuang
qhuang8
vanjeff
gikidy
jji4
eric_tian
xli24
qwang12