ZTE/SanChip version pl011 has different reg offset and bit offset
for some registers.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
According to the PI spec, Volume 3,
EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL.EraseBlocks():
> The variable argument list is a list of tuples. Each tuple describes a
> range of LBAs to erase and consists of the following:
> * An EFI_LBA that indicates the starting LBA
> * A UINTN that indicates the number of blocks to erase
(NB, in edk2, EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL is a typedef to
EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL.)
In this driver, the NumOfLba local variable is defined with type UINTN,
but the TYPE argument passed to VA_ARG() is UINT32. Fix the mismatch.
In addition, update the DEBUG macro invocation where NumOfLba is formatted
with the %d conversion specifier: UINTN values should be converted to
UINT64 and printed with %Lu or %Lx for portability between 32-bit and
64-bit.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Reported-by: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
When call PL061GetPins() or PL061SetPins(), should use GPIO_PIN_MASK(offset)
as parameter, not offset.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
ARM TZASC-380 IP provides a mechanism to split memory regions being
protected via it into eight equal-sized sub-regions. A bit-setting
allows the corresponding subregion to be disabled.
Several NXP/FSL SoCs support the TZASC-380 IP block and allow
the DDR connected via the TZASC to be partitioned into regions
having different security settings and also allow subregions
to be disabled.
This patch enables this support and can be used for SoCs which
support such a partition of DDR regions.
Details of the 'subregion_disable' register can be viewed here:
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0431c/CHDIGDCI.html
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@nxp.com>
[bhupesh.linux@gmail.com : Added gmail ID as NXP one is no longer valid]
Signed-off-by: Bhupesh Sharma <bhupesh.linux@gmail.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
In NorFlashFvbInitialize() if a valid Firmware Volume header is not found at the
start of NOR Flash, the Flash memory is written before it has been remapped with
EFI_MEMORY_UC attributes to allow write commands. Since the flash memory was
previously mapped with Normal and possibly cacheable memory attributes, the
Flash commands might never reach the device.
This patch fixes this issue by remapping the Flash memory region with correct
memory attributes before writing to it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
When CMD6 & ACMD51 are added into identifying SD process, PL180
should also support CMD6 & ACMD51. Otherwise, it will hang when
system tries to read expected data.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
While most compilers happily allow arithmetic on void pointer,
the RVCT compiler does not, and throws the following warning for
NorFlashDxe:
ArmPlatformPkg/Drivers/NorFlashDxe/NorFlashDxe.c(894,48) :
error #1254-D: arithmetic on pointer to void or function type
Since the expression in question involves a cast from UINTN to VOID*,
simply add some parentheses to eliminate this warning.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Correct some obviously incorrect comments that have invalid details for
the returned values. (Copy /Paste problem?)
There are no functional changes in this commit.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Alexei Fedorov <alexei.fedorov@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This change updates PL011UartInitializePort to compare ReceiveFifoDepth
with the correct hardware FIFO size instead of the constant 32 used
previously.
This corrects a minor bug where a request for a fifo size > 15 and < 32
would not have been honoured on a system with a 16 byte FIFO.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The UEFI spec stipulates that unaligned accesses should be enabled
on CPUs that support them, which means all of them, given that we
no longer support pre-v7 ARM cores, and the AARCH64 bindings mandate
support for unaligned accesses unconditionally.
This means that one should not assume that CopyMem () is safe to call
on regions that may be mapped using device attributes, which is the
case for the NOR flash. Since we have no control over the mappings when
running under the OS, and given that write accesses require device
mappings, we should not call CopyMem () in the read path either, but
use our own implementation that is guaranteed to take alignment into
account.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This module is now identical in functionality to NorFlashDxe, and is no
longer used, so remove it altogether.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Now that the generic Variable Runtime DXE code no longer distinguishes
between gEfiVariableGuid and gEfiAuthenticatedVariableGuid in the varstore
FV header, we can relax the check in the NOR flash driver to accept either
GUID regardless of whether we are running a secure boot capable build or not.
This also means we can always use gEfiAuthenticatedVariableGuid when we
encounter an empty NOR flash that needs to be initialized before use. So
remove the mNorFlashVariableGuid global from the shared code and from both
versions of NorFlashDxe.inf. This essentially collapses the two drivers into
a single one, which means we can remove NorFlashAuthenticatedDxe entirely
in a subsequent patch.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This change corrects 3 problems in the PL011 driver.
1. The TRM states "The UARTLCR_H, UARTIBRD, and UARTFBRD registers must
not be changed:...when the UART is enabled"
2. The TRM (3.3.8) describes logic requiring the UART to be disabled and
flushed before adjusting UARTCR.
3. Several redundant calls get made to PL011UartInitializePort, where
the characteristics do not change, but updating the registers can
cause glitches in the output stream.
The parameters are compared to the current state and no action taken if
no change of state is required.
Where an update is required, the specified logic is followed, and the
register updates only made when the UART is disabled.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
On some platforms the UART clock is not the same for all the serial
ports. The PL011 driver must be capable of handling serial ports with
different clock rates, so must not rely on a PCD for the clock rate.
This patch allows the UART clock rate to be passed as a parameter
to PL011UartInitializePort(), which is called from the serial port
library. This patch also contains the corresponding changes in the
serial port library.
The PCD in Drivers/PL011Uart is replaced by an extra parameter for
PL011UartInitializePort. The PCD is moved to Library/PL011SerialPortLib
to supply the value to pass.
A corresponding patch to ArmVirtPkg is included in the same bundle to
align that with these changes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
The variable LineControl was initialised to zero, then updated in a
condition. This change converts that to a write in each branch of the
condition, removing the Write/Read/Modify/Write sequence.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
The PCDs used in the PL011 UART Driver and Serial Port Library are
inherently "fixed at build". This change updates the source to use
Fixed PCDs for these values. This improves clarity and efficiency.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
This cosmetic change only tidies things up in preparation for actual
updates. (This reflects responses to a previously submitted patch,
which has been split into several discrete changes.)
There are no functional changes in this commit.
Changes comprise:
Minor corrections to comment typos.
Minor formatting mods.
Expansion of function comments.
Remove OUT from UartBase parameter.
Addition of #define for "magic mumbers".
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Support multiple PL061 controllers. If platform gpio driver couldn't be
found, PL061 gpio driver will continue to load PcdPL061GpioBase as the
register base.
It could be compatible with the use case of current PL061 gpio driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
TC2 reads 0x02 for the PL180 ID3 register instead of 0x00 as defined in
the spec.
However, the spec [1] states that the contents of ID3 register represent
the "configuration option of the peripheral" and thus not part of the
Prime Cell identification.
For this patch, we drop checking the value in MCI_PERIPH_ID_REG3.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0172a/index.html
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
If the PL180 fails to probe, issue a warning on debug builds.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
PL180 on TC2 has a dependency on gEfiCpuArchProtocolGuid. Without
adding the dependency, TC2 will crash in the PL180 driver.
This problem has been present since d340ef7 when TC2 stopped booting.
However, it was masked by 300fc77 which prevented PL180 from running on
TC2 due to TC2 using a version on PL180 newer than that documented
publicly.
[1] https://github.com/tianocore/edk2/commit/d340ef7
2014-08-26
ArmPkg/ArmArchTimerLib: Remove non required [depex] and IoLib
[2] https://github.com/tianocore/edk2/commit/300fc77
2015-08-25
ArmPlatformPkg/PL180MciDxe: check PrimeCell ID before initializing
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The PL061 GPIO controller is a bit of an anachronism, and the existing
driver does nothing to hide this - leading to it being very tricky to
read.
Rewrite it to document (in comments and code) what is actually
happening, and fix some bugs in the process.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
PL061Initialize() did not actually do anything other than call
PL061Identify() - so cut out the middle man.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
For whatever reason, every single operation on the PL061 looked for an
"Initialized" flag, and manually called the initialization function if
not set. Move this to a single call on protocol installation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
The copyright statement in PL061Gpio.c would not fit on a normal terminal
screen. Break lines at <= 80 characters.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Problems have been encountered because some of the source files have
execute permission set. This can cause git to report them as changed
when they are checked out onto a file system with inherited permissions.
This has been seen using Cygwin, MinGW and PowerShell Git.
This patch makes no change to source file content, and only aims to
correct the file modes/permissions.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19787 6f19259b-4bc3-4df7-8a09-765794883524
The ValidateFvHeader() function checks several conditions against the
firmware volume header. Failure of the first of these checks, reported as
"No Firmware Volume header present", is a common situation for unformatted
flash images, especially when a new virtual machine is created.
Similarly, "Variable Store Guid non-compatible" is common when the
firmware binary is switched from Secure Boot-incapable to Secure
Boot-capable, or vice versa.
The only caller of ValidateFvHeader(), NorFlashFvbInitialize(), handles
all these mismatches by installing a new FVB header. It also emits
another, loud ERROR message (which is even less justified when it is
triggered by (BootMode == BOOT_WITH_DEFAULT_SETTINGS)).
Downgrade these messages from EFI_D_ERROR to EFI_D_INFO, so that they
don't clutter the debug output when the PcdDebugPrintErrorLevel mask only
enables EFI_D_ERROR (i.e., in a "silent" build).
These messages have annoyed / confused users; see for example:
- https://bugzilla.redhat.com/show_bug.cgi?id=1270279
- http://thread.gmane.org/gmane.comp.bios.edk2.devel/2772/focus=2869
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Drew Jones <drjones@redhat.com>
Cc: Yehuda Yitschak <yehuday@marvell.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18618 6f19259b-4bc3-4df7-8a09-765794883524
Commit r18308 ("ArmPlatformPkg/LcdGraphicsOutputDxe: check PrimeCell ID
before initializing") introduced a LcdIdentify() function to the PL111
LCD driver that makes it fail gracefully when executed on hardware that
does not have the IP. However, the LcdGraphicsOutputDxe driver is shared
with the HdLcd driver, which now fails to build due to the fact that it
has no LcdIdentity() function. So add a dummy implementation that always
returns EFI_SUCCESS.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18395 6f19259b-4bc3-4df7-8a09-765794883524
To deal gracefully with the absence of the PL111 hardware on
the Foundation model, check the PrimeCell ID before proceeding
with the installation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18308 6f19259b-4bc3-4df7-8a09-765794883524
To deal gracefully with the absence of the PL180 hardware on
the Foundation model, check the PrimeCell ID before proceeding
with the installation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18307 6f19259b-4bc3-4df7-8a09-765794883524
Remove gVariableAuthenticatedRuntimeDxeFileGuid definition in
ArmPlatformPkg.dec and use gVariableRuntimeDxeFileGuid in
NorFlashAuthenticatedDxe.inf as auth Variable driver in SecurityPkg
and Variable driver in MdeModulePkg have been merged.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17768 6f19259b-4bc3-4df7-8a09-765794883524
The NorFlashDxe uses an explicit 'BEFORE xxx' Depex declaration to
ensure that it is dispatched before VariableRuntimeDxe, and uses the
file GUID of the latter as 'xxx' explicitly to accomplish that.
However, when enabling UEFI Secure Boot, this breaks down since the
authenticated VariableRuntimeDxe is a completely separate driver, with
a different GUID. Also, the hardcoded dependency on gEfiVariableGuid,
which is not used under UEFI Secure Boot, needs to be factored out in
order to allow this driver to be used.
So clone NorFlashDxe.inf into NorFlashAuthenticatedDxe.inf, and fix
up the dependencies so they refer to gEfiAuthenticatedVariableGuid and
SecurityPkg/VariableAuthenticated/RuntimeDxe/VariableRuntimeDxe.inf
instead.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17355 6f19259b-4bc3-4df7-8a09-765794883524
pl011 releases earlier than r1p5 has a fifo depth of 16 bytes, whereas
version r1p5 upwards has a fifo depth of 32 bytes. The pl011 driver was
hardwired to 32 byte depth, causing dropped characters on some platforms
(including default settings on FVP Base and Foundation models).
Update driver to select 16 or 32 on port initialization by checking the
component revision.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16656 6f19259b-4bc3-4df7-8a09-765794883524
Fix the check to prevent any reading past the end of the nor flash.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <ronald.cron@arm.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16655 6f19259b-4bc3-4df7-8a09-765794883524
Rework the PL011UartGetControl() function removing a TODO by the way.
Update of the header comment blocks of (PL011Uart|SerialPort)GetControl() functions.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <ronald.cron@arm.com>
Reviewed-By: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16252 6f19259b-4bc3-4df7-8a09-765794883524
Rework of PL011UartSetControl() as a consequence as well as update of
function header comment blocks.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <ronald.cron@arm.com>
Reviewed-By: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16251 6f19259b-4bc3-4df7-8a09-765794883524
When writing to the flash, make sure to use MmioWrite () wrappers instead
of letting the compiler generate the store instructions. This is needed
because under virtualization, store instructions with multiple outputs
(i.e., store pair or store with writeback) cannot be emulated efficiently
when operating on MMIO ranges.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-By: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16107 6f19259b-4bc3-4df7-8a09-765794883524
Replace tabs by spaces for indentation to comply to EDK2 coding standards.
Done in files with extension ".S", ".c", ".h", ".asm", ".dsc", ".inc", "*.inf",
"*.dec" or ".fdf" and located in ArmPkg, ArmPlatformPkg, EmbeddedPkg,
BeagleBoardPkg or Omap35xxPkg.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <ronald.cron@arm.com>
Reviewed-By: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15901 6f19259b-4bc3-4df7-8a09-765794883524
FVB (for instance for UEFI Variable) might not be at the
start of the NOR Flash. 'Lba' needs to be fixed up for it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15532 6f19259b-4bc3-4df7-8a09-765794883524
This improves performance by accessing NOR with the fine granularity that
the hardware permits, rather than the coarse granularity assumed by DiskIoDxe.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Brendan Jackman <brendan.jackman@arm.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15502 6f19259b-4bc3-4df7-8a09-765794883524
- Only read what needs reading, don't read the whole block.
- Don't write back buffers containing no data after an erase.
- Reduce number of NOR erases when writing data. Only erase the block
when required.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Harry Liebel <Harry.Liebel@arm.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15500 6f19259b-4bc3-4df7-8a09-765794883524
- Added the NOR Flash region to the Runtime UEFI Memory Mapped IO
- Caught the gEfiEventVirtualAddressChangeGuid event to fixup the NOR Flash pointers
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15438 6f19259b-4bc3-4df7-8a09-765794883524
- No allocation during Runtime mode (post ExitBootServices())
- Allocate all the persistent data into runtime space
- Do not access BootServices API during Runtime mode
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15437 6f19259b-4bc3-4df7-8a09-765794883524
'inline' keyword is not supported by the C89 (version used by EDK2).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14957 6f19259b-4bc3-4df7-8a09-765794883524
This patch prevents a buffer underrun error on the Versatile Express
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14793 6f19259b-4bc3-4df7-8a09-765794883524
Jun Nie
Laszlo Ersek
Haojian Zhuang
Bhupesh Sharma
Achin Gupta
Ard Biesheuvel
Alexei
Evan Lloyd
Ryan Harkin
Leif Lindholm
Star Zeng
Ronald Cron
Olivier Martin
Brendan Jackman
Harry Liebel