REF:https://bugzilla.tianocore.org/show_bug.cgi?id=4560
TRB Template is 16 bytes. When boundary checking is 64 bytes for xHCI
device/host memory address, it may exceed xHCI host memory pool and
cause unwanted DXE_ASSERT. Introduce a new input parameter to indicate
whether to enforce 64byte size alignment and round up. For TRB case,
should set it to FALSE to skip the size round up.
Signed-off-by: Gao Cheng <gao.cheng@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=4552
Following XHCI spec 4.6.1.2, software may abort the
execution of Address Device Command when command failed
due to timeout.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: More Shih <more.shih@intel.com>
Cc: Jenny Huang <jenny.huang@intel.com>
Signed-off-by: Xianglei Cai <xianglei.cai@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=2948
XhciDxe uses the timer functionality provided by the
boot services table to detect timeout conditions. This
breaks the driver's ExitBootServices call back, as
CoreExitBootServices halts the timer before signaling
the ExitBootServices event. If the host controller
fails to halt in the call back, the timeout condition
will never occur and the boot gets stuck in an indefinite
spin loop. Use the free running timer provided by
TimerLib to calculate timeouts, avoiding the potential
hang.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Patrick Henz <patrick.henz@hpe.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
The function UsbHcGetPciAddressForHostMem has
ASSERT ((Block != NULL)); and
and the function UsbHcFreeMem has
ASSERT (Block != NULL);
statement after for loop, but these are applicable only in DEBUG mode.
In RELEASE mode, if for whatever reasons there is no match inside for
loop and the loop exits because of Block != NULL; condition, then there
is no "Block" NULL pointer check afterwards and the code proceeds to do
dereferencing "Block" which will lead to CRASH.
Hence, for safety add NULL pointer checks always.
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=4211
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Co-authored-by: Veeresh Sangolli <veeresh.sangolli@dellteam.com>
Signed-off-by: Ranbir Singh <Ranbir.Singh3@Dell.com>
Signed-off-by: Ranbir Singh <rsingh@ventanamicro.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
The function UhciConvertPollRate has a check
ASSERT (Interval != 0);
but this comes into play only in DEBUG mode. In Release mode, there is
no handling if the Interval parameter value is ZERO. To avoid shifting
by a negative amount later in the code flow in this undesirable case,
it is better to handle it as well by treating it same as if 1 is sent.
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=4211
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Co-authored-by: Veeresh Sangolli <veeresh.sangolli@dellteam.com>
Signed-off-by: Ranbir Singh <Ranbir.Singh3@Dell.com>
Signed-off-by: Ranbir Singh <rsingh@ventanamicro.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
The code can reach line 65 only through the else path above at line 53.
The else path already has the same NULL check at line 55 and hence the
duplicate code lines are totally redundant which can be deleted.
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=4220
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Co-authored-by: Veeresh Sangolli <veeresh.sangolli@dellteam.com>
Signed-off-by: Ranbir Singh <Ranbir.Singh3@Dell.com>
Signed-off-by: Ranbir Singh <rsingh@ventanamicro.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
A faulty PCI device has the Option ROM image size set to 0. UEFI reads
two headers PCI_EXPANSION_ROM_HEADER and PCI_DATA_STRUCTURE to get the
Option ROM information. Because the image size is 0, the Option ROM
header address never changes. As a result, UEFI keeps reading the same
two headers definitely. This patch is intended to fix it.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Nhi Pham <nhi@os.amperecomputing.com>
Reviewed-by: Liming Gao <gaoliming@byosoft.com.cn>
The function UsbHcGetPciAddressForHostMem has
ASSERT ((Block != NULL));
and the UsbHcFreeMem has
ASSERT (Block != NULL);
statement after for loop, but these are applicable only in DEBUG mode.
In RELEASE mode, if for whatever reasons there is no match inside the
for loop and the loop exits because of Block != NULL; condition, then
there is no "Block" NULL pointer check afterwards and the code proceeds
to do dereferencing "Block" which will lead to CRASH.
Hence, for safety add NULL pointer checks always.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=4210
Signed-off-by: Ranbir Singh <Ranbir.Singh3@Dell.com>
Signed-off-by: Ranbir Singh <rsingh@ventanamicro.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
ASSERT (Private != NULL) (where Private = CR(...)) is ineffective as
CR(Ptr, Type, Member, Sig) either returns Ptr - offsetof(Type, Member),
or ASSERTS on the signature, so it's unlikely to ever return NULL (must
be passed a pointer = member's offset, or in this case, 0x4).
ASSERT on This != NULL instead.
Signed-off-by: Pedro Falcato <pedro.falcato@gmail.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
When a UEFI_DRIVER attempts to open a protocol interface with BY_DRIVER
attribute that it already has open with BY_DRIVER attribute,
OpenProtocol() returns EFI_ALREADY_STARTED. This is not an error. The
UEFI-2.7 spec currently says,
> EFI_ALREADY_STARTED -- Attributes is BY_DRIVER and there is an item on
> the open list with an attribute of BY_DRIVER
> whose agent handle is the same as AgentHandle.
Downgrade the log mask for this one condition to DEBUG_INFO, in
SataControllerStart(). This will match the log mask of the other two
informative messages in this function.
(ported from commit 5dfba97)
Signed-off-by: Pedro Falcato <pedro.falcato@gmail.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=4394
Fix DumpCapabilityReg() debug log to print 64 bit capability instead of
32 bit pointer
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Andrew Fish <afish@apple.com>
Signed-off-by: Giri Mudusuru <girim@apple.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
This applies the volatile keyword and appropriate casts
to the NvmExpressPei's Passthru CQ.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Michael Kubacki <mikuback@linux.microsoft.com>
Cc: Sean Brogan <sean.brogan@microsoft.com>
Signed-off-by: Oliver Smith-Denny <osde@linux.microsoft.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Acked-by: Michael Kubacki <michael.kubacki@microsoft.com>
This updates the relevant functions that expect a non-volatile
structure to be passed to them to take casts of the CQ
now that it is volatile.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Michael Kubacki <mikuback@linux.microsoft.com>
Cc: Sean Brogan <sean.brogan@microsoft.com>
Signed-off-by: Oliver Smith-Denny <osde@linux.microsoft.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Acked-by: Michael Kubacki <michael.kubacki@microsoft.com>
__FUNCTION__ is a pre-standard extension that gcc and Visual C++ among
others support, while __func__ was standardized in C99.
Since it's more standard, replace __FUNCTION__ with __func__ throughout
MdeModulePkg.
Signed-off-by: Rebecca Cran <rebecca@bsdio.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
In V4: Update the copyright to 2023.
In V3: Add AMD copyright.
In V2: Remove the signed-off-by: Abner Chang
Display PCIe Vendor ID and Device ID in DEBUG message.
Signed-off-by: Jiangang He <jiangang.he@amd.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Garrett Kirkendall <garrett.kirkendall@amd.com>
Cc: Abner Chang <abner.chang@amd.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Michael D Kinney <michael.d.kinney@intel.com>
Unlink the XhciPei memory block when it has been freed.
Signed-off-by: Jiangang He <jiangang.he@amd.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Garrett Kirkendall <garrett.kirkendall@amd.com>
Cc: Abner Chang <abner.chang@amd.com>
Cc: Kuei-Hung Lin <Kuei-Hung.Lin@amd.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Force resetting the port by clearing the USB_PORT_STAT_C_RESET bit in
PortChangeStatus when XhcPollPortStatusChange fails
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
On some platforms, including Sky Lake and Kaby Lake, the PSIV (Protocol
Speed ID Value) indices are shared between Protocol Speed ID DWORD' in
the extended capabilities registers for both USB2 (Full Speed) and USB3
(Super Speed).
An example can be found below:
XhcCheckUsbPortSpeedUsedPsic: checking for USB2 ext caps
XhciPsivGetPsid: found 3 PSID entries
XhciPsivGetPsid: looking for port speed 1
XhciPsivGetPsid: PSIV 1 PSIE 2 PLT 0 PSIM 12
XhciPsivGetPsid: PSIV 2 PSIE 1 PLT 0 PSIM 1500
XhciPsivGetPsid: PSIV 3 PSIE 2 PLT 0 PSIM 480
XhcCheckUsbPortSpeedUsedPsic: checking for USB3 ext caps
XhciPsivGetPsid: found 3 PSID entries
XhciPsivGetPsid: looking for port speed 1
XhciPsivGetPsid: PSIV 1 PSIE 3 PLT 0 PSIM 5
XhciPsivGetPsid: PSIV 2 PSIE 3 PLT 0 PSIM 10
XhciPsivGetPsid: PSIV 34 PSIE 2 PLT 0 PSIM 1248
The result is edk2 detecting USB2 devices as USB3 devices, which
consequently causes enumeration to fail.
To avoid incorrect detection, check the Compatible Port Offset to find
the starting Port of Root Hubs that support the protocol.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
PSID matching relies on comparing the PSIV against the PortSpeed
value. This patch stops edk2 from checking for a PSIV of 0, as it
is not valid; this reduces the number of register access by
approximately 6 per second.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
SD1.0 cards don't support CMD8 and CMD6
CMD8 result can be used to distinguish the card is SD1.0 or not.
CMD8 result can be used to decide following CMD6 is sent or skip.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Signed-off-by: Chevron Li <chevron.li@bayhubtech.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
With the pending commit of UsbNetworkPkg, it will become common for
UsbBulkTransfer calls to timeout, given that the drivers are called from
MnpSystemPoll every MNP_SYS_POLL_INTERVAL milliseconds: the drivers
check for network packets by calling UsbBulkTransfer with a timeout of
1ms.
Avoid console spam by moving DEBUG messages that occur each time a bulk
transfer request times out from DEBUG_ERROR to DEBUG_VERBOSE, for both
EHCI and XHCI drivers.
Signed-off-by: Rebecca Cran <rebecca@quicinc.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
gSerialDevTempate should be gSerialDevTemplate
Cc: Ray Ni <ray.ni@intel.com>
Cc: Zhichao Gao <zhichao.gao@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Signed-off-by: Nate DeSimone <nathaniel.l.desimone@intel.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
According the Xhci Spec, TRB Rings may be larger than a Page, however they
shall not cross a 64K byte boundary, so add a parameter to indicate
whether the memory allocation is for TRB Rings or not. It will ensure the
allocation not crossing 64K boundary in UsbHcAllocMemFromBlock if the
memory is allocated for TRB Rings.
Signed-off-by: jdzhang <jdzhang@kunluntech.com.cn>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
If a device which support both features SR-IOV/ARI has multi
functions, which maybe support 8-255. After enable ARI forwarding in
the root port and ARI Capable Hierarchy in the SR-IOV PF0.
The device will support and expose multi functions(0-255) with ARI ID routing.
In next device loop in below for() code, actually it still be in the
same SR-IOV device, and just some PF which is over 8 or higher
one(n*8), PciAllocateBusNumber() will allocate bus
number(ReservedBusNum - TempReservedBusNum)) for this PF. if reset
TempReservedBusNum as 0 in this case,it will allocate wrong bus number
for this PF because TempReservedBusNum should be total previous PF's
reserved bus numbers.
code:
for (Device = 0; Device <= PCI_MAX_DEVICE; Device++) {
TempReservedBusNum = 0;
for (Func = 0; Func <= PCI_MAX_FUNC; Func++) {
//
// Check to see whether a pci device is present
//
Status = PciDevicePresent (
PciRootBridgeIo,
&Pci,
StartBusNumber,
Device,
Func
);
...
Status = PciAllocateBusNumber (PciDevice, *SubBusNumber,
(UINT8)(PciDevice->ReservedBusNum - TempReservedBusNum), SubBusNumber);
The solution is add a new flag IsAriEnabled to help handle this case.
if ARI is enabled, then TempReservedBusNum will not be reset again
during all functions(1-255) scan with checking flag IsAriEnabled.
Signed-off-by: Foster Nong <foster.nong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Below code will calculate the reserved bus number for the each PF.
Based on the VF routing ID algorithm, PFRid and LastVF in below code
already sure that "All VFs and PFs must have distinct Routing IDs".
PF will be assigned Routing ID based on secBusNumber, ReservedBusNum
will add into SubBusNumber directly. So the SR-IOV device will be
assigned bus range as SecBusNumber ~ (SubBusNumber=(SecBusNumber +
ReservedBusNum)).
Thus "+1" in below code will cause extra 1 bus, and introduce a bus hole.
PFRid = EFI_PCI_RID (Bus, Device, Func);
LastVF = PFRid + FirstVFOffset + (PciIoDevice->InitialVFs - 1) * VFStride;
PciIoDevice->ReservedBusNum = (UINT16)(EFI_PCI_BUS_OF_RID (LastVF) -
Bus + 1);
In SR-IOV spec, there is a note in section 2.1.2:
Note: Bus Numbers are a constrained resource. Devices are strongly
encouraged to avoid leaving ?holes? in their Bus Number usage to avoid
wasting Bus Numbers
So the issue can be fixed with below code change.
PciIoDevice->ReservedBusNum = (UINT16)(EFI_PCI_BUS_OF_RID (LastVF) -
Bus);
https://bugzilla.tianocore.org/show_bug.cgi?id=4069
Signed-off-by: Foster Nong <foster.nong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Per the section 3.3.5 SR-IOV spec v1.1, InitialVFs (0ch).
InitialVFs indicates to SR-PCIM the number of VFs that are initially associated with the PF.
The minimum value of InitialVFs is 0.
Below code is used to calculate SR-IOV reserved bus number,
if InitialVFs =0, it maybe calculate the wrong bus number in this case.
LastVF = PFRid + FirstVFOffset + (PciIoDevice->InitialVFs - 1) * VFStride
we can fix it with below code:
if (PciIoDevice->InitialVFs == 0) {
PciIoDevice->ReservedBusNum = 0;
} else {
PFRid = EFI_PCI_RID (Bus, Device, Func);
LastVF = PFRid + FirstVFOffset + (PciIoDevice->InitialVFs - 1) * VFStride;
//
// Calculate ReservedBusNum for this PF
//
PciIoDevice->ReservedBusNum = (UINT16)(EFI_PCI_BUS_OF_RID (LastVF) - Bus + 1);
//
// Calculate ReservedBusNum for this PF
//
PciIoDevice->ReservedBusNum = (UINT16)(EFI_PCI_BUS_OF_RID (LastVF) - Bus + 1);
}
https://bugzilla.tianocore.org/show_bug.cgi?id=4069
Signed-off-by: Foster Nong <foster.nong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Add support for partial free of non cached buffers.
If a request for less than the full size is requested new allocations
for the remaining head and tail of the buffer are added to the list.
Added verification that Buffer is EFI_PAGE_SIZE aligned.
The XHCI driver does this if the page size for the controller is >4KB.
Signed-off-by: Jeff Brasen <jbrasen@nvidia.com>
Acked-by: Liming Gao <gaoliming@byosoft.com.cn>
Updates debug macros in the package that have an imbalanced number
of print specifiers to arguments. These changes try to preserve
what was likely intended by the author. In cases information was
missing due to the bug, the specifier may be removed since it was
not previously accurately printing the expected value.
Cc: Dandan Bi <dandan.bi@intel.com>
Cc: Guomin Jiang <guomin.jiang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Michael Kubacki <michael.kubacki@microsoft.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <gaoliming@byosoft.com.cn>
https://bugzilla.tianocore.org/show_bug.cgi?id=4017
This change modifies NvmExpressPei library
to allow usage both EDKII_PCI_DEVICE_PPI and
EDKII_NVM_EXPRESS_HOST_CONTROLLER_PPI to manage Nvme device.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Xiao X Chen <xiao.x.chen@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Ref:https://bugzilla.tianocore.org/show_bug.cgi?id=4000
Change flow to bus scan all root bridge instances even when any
one root bridge meet bus resource OUT_OF_RESOURCE case.
thus platform handler of "EfiPciHostBridgeEndBusAllocation" has
an chance to do relative pci bus rebalance to handle this case.
Signed-off-by: Foster Nong <foster.nong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Add support process Port Speed field value of PORTSC according to
Supported Protocol Capability (define in xHCI spec 1.1)
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3914
The value of Port Speed field in PORTSC bit[10:13]
(xHCI spec 1.1 section 5.4.8) should be change to use this value to
query thru Protocol Speed ID (PSI) (xHCI spec 1.1 section 7.2.1)
in xHCI Supported Protocol Capability and return the value according
the Protocol Speed ID (PSIV) Dword.
With this mechanism may able to detect more kind of Protocol Speed
in USB3 and also compatiable with three kind of speed of USB2.
Cc: Jenny Huang <jenny.huang@intel.com>
Cc: More Shih <more.shih@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Ian Chiu <Ian.chiu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3954
Report error if reserved bits are not 0 for PageSize
Cc: Ray Ni <ray.ni@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Signed-off-by: Heng Luo <heng.luo@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
RFC: https://bugzilla.tianocore.org/show_bug.cgi?id=3429
Function of UpdatePciInfo() in PciEnumeratorSupport.c is used to update
the bar information for those incompatible PCI device. It is the right
place to check if the OptionRom need to be ignored.
According to "Table 20. ACPI 2.0 & 3.0 QWORD Address Space Descriptor
Usage" in PI Spec 1.7, Type-specific flags can be set to 0 when Address
Translation Offset == 6 to skip device option ROM (do not probe option
rom BAR).
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
Previous commit fixed that check in DXE, this one now for PEI.
Signed-off-by: Mara Sophie Grosch <littlefox@lf-net.org>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Fix the check for NVMe command set being supported by the controller.
Was problematic with qemu (6.2.0, Debian 1:6.2+dfsg-3), which sets 0xC1
in that register, making the OVMF think the NVMe controller does not
support NVMe.
Uncovered by commit 9dd14fc91c, which
changed the number of bits included in the Css register from 4 to 8.
Signed-off-by: Mara Sophie Grosch <littlefox@lf-net.org>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
The default 1s timeout can delay boot splash on some hardware with no
benefit.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=3856
Currently this NvmeExpress Driver do not support metadata handling.
According to the NVME specs, metadata may be transferred to the host after
the logical block data. It can overrun the input buffer which may only
be the size of logical block data.
Add a check to return not support for the namespaces formatted with
metadata.
v2 changes:
- Change debug log level from INFO to ERROR
- Change to if (NamespaceData->LbaFormat[LbaFmtIdx].Ms != 0)
v1: https://edk2.groups.io/g/devel/message/87242
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Hua Ma <hua.ma@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Move the logic that stores starting PCI attributes and sets the
EFI_PCI_IO_ATTRIBUTE_DUAL_ADDRESS_CYCLE attribute to
DriverBindingStart() before the memory that backs the
DMA engine is allocated.
This ensures that the DMA-backing memory is not forcibly allocated
below 4G in system address map. Otherwise the allocation fails on
platforms that do not have any memory below the 4G mark and the drive
initialisation fails.
Leave the PCI device enabling attribute logic in NvmeControllerInit()
to ensure that the device is re-enabled on reset in case it was
disabled via PCI attributes.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Leif Lindholm <quic_llindhol@quicinc.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Tomas Pilar <quic_tpilar@quicinc.com>
Acked-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3811
Remove ASSERT() statements that are triggered if a platform provides
an override of PCI ROM attached to a PCI Controller. The PCI Platform
Protocol allows the platform to provide a PCI ROM image for a PCI
Controller. This works for PCI Controllers that do not have an attached
PCI ROM, but the platform is not allowed to replace the PCI ROM for a
PCI Controller that has its own PCI ROM. Removing these ASSERT()
statements enables this additional use case.
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
This changes is by adding 50ms delay during voltage switching from 3.3V to
1.8V, plus adding a goto Voltage33Retry for 3.3V checking and retrying.
Change is for Enabling OS boot from SD card through UEFI payload.
Signed-off-by: Aiman Rosli <muhammad.aiman.rosli@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Before trying to access parent root port to check ARI capabilities,
enumerator should see if Endpoint device is not Root Complex integrated
to avoid undefined parent register accesses.
Signed-off-by: Damian Bassa <damian.bassa@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
When use the UsbHcAllocMemFromBlock() and UsbHcFreeMem() to allocate
memory and free memory for the UHC, it should use the corresponding host
address but not the pci bus address.
Signed-off-by: jdzhang <jdzhang@zd-tech.com.cn>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3737
Apply uncrustify changes to .c/.h files in the MdeModulePkg package
Cc: Andrew Fish <afish@apple.com>
Cc: Leif Lindholm <leif@nuviainc.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Signed-off-by: Michael Kubacki <michael.kubacki@microsoft.com>
Reviewed-by: Liming Gao <gaoliming@byosoft.com.cn>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3767
Update use of DEBUG_CODE(Expression) if Expression is a complex code
block with if/while/for/case statements that use {}.
Cc: Andrew Fish <afish@apple.com>
Cc: Leif Lindholm <leif@nuviainc.com>
Cc: Michael Kubacki <michael.kubacki@microsoft.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Liming Gao <gaoliming@byosoft.com.cn>
Gao Cheng
Cai, Xianglei
Henz, Patrick
Ranbir Singh
Nhi Pham
likun su
Pedro Falcato
Giri Mudusuru
Oliver Smith-Denny
Rebecca Cran
Michael Kubacki
Abner Chang
Sean Rhodes
Matt DeVillier
Chevron Li (WH)
Rebecca Cran
Nate DeSimone
jdzhang
Foster Nong
Jeff Brasen via groups.io
Chen, Xiao X
Ian Chiu
Luo, Heng
Min Xu
Mara Sophie Grosch via groups.io
Ma, Hua
Tomas Pilar
Michael D Kinney
Aiman Rosli
Ray Ni
jdzhang