https://bugzilla.tianocore.org/show_bug.cgi?id=1882
The new notify phase allows platform to configure additional
bus parameters in addition to parameters that can already be configured
with capability override. Specifically we allow to configure bus width,
clock frequency and driver strength. If platform doesn't wish to configure
some of the parameters it can left it on default values and driver will
assume it's standard behavior with respect to those parameters.
The definition of the SD_MMC_BUS_MODE has been extended to
incorporate SD card default speed and high speed.
Tests on Marvell boards were also performed by Marcin Wojtas
<mw@semihalf.com>:
https://edk2.groups.io/g/devel/message/42999
Board 1 (out of tree): SD - OK, MMC - OK
Board 2: (Armada80x0McBin): SD - OK, MMC - OK
Board 3: (Armada70x0Db): SD - problems, MMC - OK
Please note that the problem on Armada70x0Db SD devices are introduced by
adding new types of SD bus modes, a subsequent patch within edk2-platforms
repository will be proposed to address it.
(More details can be referred from the above link.)
Signed-off-by: Mateusz Albecki <mateusz.albecki@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Regression-tested-by: Sumit Garg <sumit.garg@linaro.org>
REF: https://github.com/tianocore/tianocore.github.io/wiki/
UEFI-Capsule-on-Disk-Introducation
CoDCheckCapsuleOnDiskFlag() is to check if CapsuleOnDisk flag in
"OsIndications" Variable is enabled. It is used to indicate whether
capsule on disk is provisioned in normal boot path.
CoDClearCapsuleOnDiskFlag() is to to clear CapsuleOnDisk flags,
including "OsIndications" and "BootNext" variable.
CoDRelocateCapsule() is to relocate the capsules from EFI system
partition. Depends on PcdCapsuleInRamSupport, there are two solutions
to relocate the capsule on disk images:
When Capsule In Ram is supported, the Capsule On Disk images are
relocated into memory, and call UpdateCapsule() service to deliver
the capsules.
When Capsule In Ram is not supported, the Capsule On Disk images are
relocated into a temp file which will be stored in root directory on
a platform specific storage device. CapsuleOnDiskLoadPei PEIM will
retrieve the capsules from the relocation temp file and report
capsule hobs for them.
CoDRemoveTempFile() is to remove the relocation temp file in the next
boot after capsules are processed.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Chao B Zhang <chao.b.zhang@intel.com>
Signed-off-by: Wei6 Xu <wei6.xu@intel.com>
Reviewed-by: Chao B Zhang <chao.b.zhang@intel.com>
Acked-by: Hao A Wu <hao.a.wu@intel.com>
REF: https://github.com/tianocore/tianocore.github.io/wiki/
UEFI-Capsule-on-Disk-Introducation
This patch will add Capsule On Disk related definition, including
GUID, PPI and PCDs:
The Capsule On Disk Name GUID indicates the capsule is to store
Capsule On Disk file names.
The Pei Capsule On Disk PPI provides service to retrieve capsules
from Capsule On Disk temp relocation file on mass storage devices
and create capsule hob for these capsules.
Pei Boot In CapsuleOnDisk Mode Ppi indicates current boot mode is
capsule on disk mode.
PcdCapsuleOnDiskSupport is used to enable/disable Capsule On Disk.
PcdCapsuleInRamSupport is used to enable/disable Capsule In Ram.
PcdCoDRelocationFileName specifies the Capsule On Disk temp
relocation file name.
PcdCodRelocationDevPath specifies platform specific device to store
Capsule On Disk temp relocation file.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Chao B Zhang <chao.b.zhang@intel.com>
Signed-off-by: Wei6 Xu <wei6.xu@intel.com>
Reviewed-by: Chao B Zhang <chao.b.zhang@intel.com>
Acked-by: Hao A Wu <hao.a.wu@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=1879
This commit will add the definitions of Nvm Express PassThru PPI.
This PPI will provide services that allow NVM commands to be sent
to NVM Express devices during PEI phase.
More specifically, the PPI will provide services to:
* Sends an NVM Express Command Packet to an NVM Express controller
or namespace (by service 'PassThru');
* Get the list of the attached namespaces on a controller
(by services 'GetNextNameSpace');
* Get the identification information (DevicePath) of the underlying
NVM Express host controller (by service 'GetDevicePath').
Signed-off-by: Maggie Chu <maggie.chu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
https://github.com/tianocore/tianocore.github.io/wiki/UEFI-Capsule-
on-Disk-Introducation
CoDCheckCapsuleOnDiskFlag() is to check if CapsuleOnDisk flag in
"OsIndications" Variable is enabled. It is used to indicate whether
capsule on disk is provisioned in normal boot path.
CoDClearCapsuleOnDiskFlag() is to to clear CapsuleOnDisk flags,
including "OsIndications" and "BootNext" variable.
CoDRelocateCapsule() is to relocate the capsules from EFI system
partition. Depends on PcdCapsuleInRamSupport, there are two solutions
to relocate the capsule on disk images:
When Capsule In Ram is supported, the Capsule On Disk images are
relocated into memory, and call UpdateCapsule() service to deliver
the capsules.
When Capsule In Ram is not supported, the Capsule On Disk images are
relocated into a temp file which will be stored in root directory on
a platform specific storage device. CapsuleOnDiskLoadPei PEIM will
retrieve the capsules from the relocation temp file and report
capsule hobs for them.
CoDRemoveTempFile() is to remove the relocation temp file in the next
boot after capsules are processed.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Chao B Zhang <chao.b.zhang@intel.com>
Signed-off-by: Wei6 Xu <wei6.xu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Chao B Zhang <chao.b.zhang@intel.com>
https://github.com/tianocore/tianocore.github.io/wiki/UEFI-Capsule-
on-Disk-Introducation
This patch will add Capsule On Disk related definition, including
GUID, PPI and PCDs:
The Capsule On Disk Name GUID indicates the capsule is to store
Capsule On Disk file names.
The Pei Capsule On Disk PPI provides service to retrieve capsules
from Capsule On Disk temp relocation file on mass storage devices
and create capsule hob for these capsules.
Pei Boot In CapsuleOnDisk Mode Ppi indicates current boot mode is
capsule on disk mode.
PcdCapsuleOnDiskSupport is used to enable/disable Capsule On Disk.
PcdCapsuleInRamSupport is used to enable/disable Capsule In Ram.
PcdCoDRelocationFileName specifies the Capsule On Disk temp
relocation file name.
PcdCodRelocationDevPath specifies platform specific device to store
Capsule On Disk temp relocation file.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Cc: Chao B Zhang <chao.b.zhang@intel.com>
Signed-off-by: Wei6 Xu <wei6.xu@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Reviewed-by: Chao B Zhang <chao.b.zhang@intel.com>
SERIAL_DXE_FILE_GUID is used in different places, create a single
define that other can use. Also fix SerialDxe to actually use
EDKII_SERIAL_PORT_LIB_VENDOR_GUID in the device path instead of the
FILE_GUID.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190606131459.1464-2-anthony.perard@citrix.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1722
Since we have merged this one into MdePkg,
remove it now.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao A Wu <hao.a.wu@intel.com>
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1458
Add a new API ResetSystemWithSubtype's prototype declaration in
header file. Also add the required data type header file.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Sean Brogan <sean.brogan@microsoft.com>
Cc: Michael Turner <Michael.Turner@microsoft.com>
Cc: Bret Barkelew <Bret.Barkelew@microsoft.com>
Signed-off-by: Zhichao Gao <zhichao.gao@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1460
Refer to Uefi spec 2.8, the ResetData is valid while ResetStatus
is EFI_SUCCESS regardless of the ResetType is EfiResetPlatformSpecific
or not.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Sean Brogan <sean.brogan@microsoft.com>
Cc: Michael Turner <Michael.Turner@microsoft.com>
Cc: Bret Barkelew <Bret.Barkelew@microsoft.com>
Signed-off-by: Zhichao Gao <zhichao.gao@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Introduce a protocol that can be invoked by the image loading services
to execute foreign architecture PE/COFF images via an emulator.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1683
We will remove IntelFrameworkModulePkg,
but BaseUefiTianoCustomDecompressLib may still need
to be used. So move BaseUefiTianoCustomDecompressLib
from IntelFrameworkModulePkg to MdeModulePkg.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1549
Add a debug PPI for PEI phase. This PPI will provide basic
services of debug. PEI debug lib instance can use these
services to implement debug function to reduce the PEIMs
which consume the debug lib.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Zhichao Gao <zhichao.gao@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Sean Brogan <sean.brogan@microsoft.com>
Cc: Michael Turner <Michael.Turner@microsoft.com>
Cc: Bret Barkelew <Bret.Barkelew@microsoft.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1536
To avoid the confusion caused by function name,
rename EfiBootManagerGetNextFullDevicePath to
EfiBootManagerGetNextLoadOptionDevicePath.
As an API function should add EFIAPI prefix for this function.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1460
Add the new API ResetSystem in the related head file so that
the consumer can use it through the combination of library
instance and head file.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Zhichao Gao <zhichao.gao@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1409
This commit will add the support to enlarge a LockBox when using the
LockBoxLib API UpdateLockBox().
Please note that the new support will ONLY work for LockBox with attribute
LOCK_BOX_ATTRIBUTE_RESTORE_IN_S3_ONLY set.
The functional uni-test for the commit is available at:
https://github.com/hwu25/edk2/tree/lockbox_unitest
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1409
This commit will add the GUID definitions for LockBox which is used to
save a list of storage devices that need to get initialized during the S3
resume.
The content of the LockBox will be a DevicePath structure that contains
zero or more DevicePath instances. Each instance denotes a storage device
that needs to get initialized during the S3 resume.
The producers of the content of this LockBox will be drivers like
OpalPassword DXE driver. This kind of drivers requires some specific
storage devices to be initialized during the PEI phase of in S3 resume.
(For the OpalPassword case, it requires the managing devices to be
automatically unlocked during the S3 resume).
The attribute of the LockBox should be set to
LOCK_BOX_ATTRIBUTE_RESTORE_IN_S3_ONLY.
The consumers of the content of this LockBox will be PEI storage device
controller/bus drivers (e.g. NvmExpressPei) during S3 resume. This kind of
drivers can use the DevicePath instances stored in the LockBox to get a
list of devices that need to get initialized. In such way, an on-demand
(partial) device enumeration/initialization can be performed to benefit
the S3 resume performance.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@Intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1409
This commit will add the definitions for Storage Security Command (SSC)
PPI. This PPI will be be used to abstract mass storage devices to allow
code running in the PEI phase to send security protocol commands to mass
storage devices without specific knowledge of the type of device or
controller that manages the device.
More specifically, the PPI will provide services to:
* Get the number of mass storage devices managed by a instance of the SSC
PPI (by service 'GetNumberofDevices');
* Get the identification information (DevicePath) of a managing mass
storage devices (by service 'GetDevicePath');
* Send security protocol commands to mass storage devices (by services
'ReceiveData' and 'SendData').
Cc: Jian J Wang <jian.j.wang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1409
This commit will add the definitions for EDKII PEI ATA PassThru PPI. This
PPI will provide services that allow ATA commands to be sent to ATA
devices attached to an ATA controller in the PEI phase.
More specifically, the PPI will provide services to:
* Send ATA commands to an ATA device (by service 'PassThru');
* Get the list of the attached ATA device on a controller (by services
'GetNextPort' and 'GetNextDevice');
* Get the identification information (DevicePath) of the underlying ATA
host controller (by service 'GetDevicePath').
Cc: Jian J Wang <jian.j.wang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1409
This commit will add the definitions for ATA AHCI host controller PPI. The
purpose of the PPI in to provide:
* MMIO base address
* Controller identification information (DevicePath)
for ATA host controllers working under AHCI mode.
Cc: Jian J Wang <jian.j.wang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ:https://bugzilla.tianocore.org/show_bug.cgi?id=1482
Add a new function to support Capsule-on-Disk feature.
This function is used to get next full DevicePath from a load option.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Cc: Zhang Chao B <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
Some SdMmc host controllers are run by clocks with different
frequency than it is reflected in Capabilities Register 1.
It is allowed by SDHCI specification ver. 4.2 - if BaseClkFreq
field value of the Capability Register 1 is zero, the clock
frequency must be obtained via another method.
Because the bitfield is only 8 bits wide, a maximum value
that could be obtained from hardware is 255MHz.
In case the actual frequency exceeds 255MHz, the 8-bit BaseClkFreq
member of SD_MMC_HC_SLOT_CAP structure occurs to be not sufficient
to be used for setting the clock speed in SdMmcHcClockSupply
function.
This patch adds new UINT32 array ('BaseClkFreq[]') to
SD_MMC_HC_PRIVATE_DATA structure for specifying
the input clock speed for each slot of the host controller.
All routines that are used for clock configuration are
updated accordingly.
This patch also adds new IN OUT BaseClockFreq field
in the Capability callback of the SdMmcOverride,
protocol which allows to update BaseClkFreq value.
The patch reuses original commit from edk2-platforms:
20f6f144d3a8 ("Marvell/Drivers: XenonDxe: Allow overriding base clock
frequency")
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Some SD Host Controlers need to do additional operations after clock
frequency switch.
This patch add new callback type to NotifyPhase of the SdMmcOverride
protocol. It is called after SdMmcHcClockSupply.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Some SD Host Controllers use different values in Host Control 2 Register
to select UHS Mode. This patch adds a new UhsSignaling type routine to
the NotifyPhase of the SdMmcOverride protocol.
UHS signaling configuration is moved to a common, default routine
(SdMmcHcUhsSignaling). After it is executed, the protocol producer
can override the values if needed.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
In order to ensure bigger flexibility in the NotifyPhase
routine of the SdMmcOverride protocol, enable using an
optional phase-specific data. This will allow to exchange
more information between the protocol producer driver
and SdMmcPciHcDxe in the newly added callbacks.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Removing rules for Ipf sources file:
* Remove the source file which path with "ipf" and also listed in
[Sources.IPF] section of INF file.
* Remove the source file which listed in [Components.IPF] section
of DSC file and not listed in any other [Components] section.
* Remove the embedded Ipf code for MDE_CPU_IPF.
Removing rules for Inf file:
* Remove IPF from VALID_ARCHITECTURES comments.
* Remove DXE_SAL_DRIVER from LIBRARY_CLASS in [Defines] section.
* Remove the INF which only listed in [Components.IPF] section in DSC.
* Remove statements from [BuildOptions] that provide IPF specific flags.
* Remove any IPF sepcific sections.
Removing rules for Dec file:
* Remove [Includes.IPF] section from Dec.
Removing rules for Dsc file:
* Remove IPF from SUPPORTED_ARCHITECTURES in [Defines] section of DSC.
* Remove any IPF specific sections.
* Remove statements from [BuildOptions] that provide IPF specific flags.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This patch updates IP4 stack to support 32bit subnet mask in PXE boot process.
When 32bit subnet mask is used, the IP4 driver couldn't use the subnet mask to determine
whether destination IP address is on-link or not, so it will always try to send all the
packets to the destination IP address directly first, if failed it will continue
to try the default gateway.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
The patch adds a new API PlatformBootManagerUnableToBoot()
to PlatformBootManagerLib.
The new API is provided by platform bds library and is called when
no boot option could be launched.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Sean Brogan <sean.brogan@microsoft.com>
Cc: Michael Turner <Michael.Turner@microsoft.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
It is caused by change d1102dba72.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
1. Do not use tab characters
2. No trailing white space in one line
3. All files must end with CRLF
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Update the performance library instances in MdeModulePkg
to implement the APIs used for new added Perf macros.
V2:
Share the common logics of creating FPDT record for
new added Perf macros and existing Perf macros.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Remove the definitions of performance identifier since they
have been added into PerformanceLib.h.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Introduces the below PPI:
struct EDKII_NVM_EXPRESS_HOST_CONTROLLER_PPI {
EDKII_NVM_EXPRESS_HC_GET_MMIO_BAR GetNvmeHcMmioBar;
EDKII_NVM_EXPRESS_HC_GET_DEVICE_PATH GetNvmeHcDevicePath;
};
The GetNvmeHcMmioBar service will provide the caller with the MMIO BAR
address of each NVMe HC within the system;
The GetNvmeHcDevicePath service will provide the caller with the device
path information of each NVMe HC.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
The patch adds AtaAtapiPolicy protocol which is produced by platform
and consumed by AtaAtapiPassThruDxe driver.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=801
Based on content from the following branch/commits:
https://github.com/Microsoft/MS_UEFI/tree/share/MsCapsuleSupport
Add the DisplayUpdateProgressLib class that is used
to inform the user of progress during updates of
firmware images in firmware devices. A platform
specific instance of this library can be used to
customize how the user is informed of progress.
Add the EDK II Firmware Management Progress Protocol.
This is an optional protocol that must be installed
onto the same handle as a Firmware Management Protocol.
This new protocol provides the color of a progress
bar that allows different firmware devices to use
different colors during a firmware update. It also
provides a watchdog timer value in seconds that is
armed each time the Progress() service passed
into Firmware Management Protocol SetImage()
is called.
Cc: Sean Brogan <sean.brogan@microsoft.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Clean up the leading comment and the prototype of
EfiBootManagerAddLoadOptionVariable():
- the function may modify Option on output, annotate the parameter with
OUT and update the documentation;
- "@retval EFI_STATUS" and "@retval Others" are not idiomatic
documentation, use @return instead;
- sync comment and prototype between lib instance and lib class header.
Change-Id: I8a609d6502b6f8929b2f568acaa147065003b6f4
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
1. Fix some "support" to "supported".
2. Fix some "set" to "clear" in ClearMemoryAttributes interface.
3. Remove redundant comments for GetMemoryAttributes interface.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Add Translation field to PCI_ROOT_BRIDGE_APERTURE. Translation is used
to represent the difference between device address and host address,
if they are not the same on some platforms.
In UEFI 2.7, "Address Translation Offset" is "Offset to apply to the
Starting address to convert it to a PCI address". This means:
Translation = device address - host address
So we also use the above calculation for this Translation field to
keep consistent.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Signed-off-by: Yi Li <phoenix.liyi@huawei.com>
Reviewed-by: Ni Ruiyu <ruiyu.ni@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Remove PCD_TYPE_SKU_ENABLED in PCD_TYPE_ALL_SET.
This change was missing at e8d2a98052.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Thomas Lamprecht <t.lamprecht@proxmox.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Tested-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Eric Dong <eric.dong@intel.com>
PcdDb optimization has handled PCD DB for each SKU, not for single PCD.
So, this PCD attribute is not used any more.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
With this flag, the LockBox can be restored in S3 resume only.
The LockBox can not be restored after SmmReadyToLock in normal boot
and after EndOfS3Resume in S3 resume.
It can not be set together with LOCK_BOX_ATTRIBUTE_RESTORE_IN_PLACE.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Add gEdkiiS3SmmInitDoneGuid, after S3 SMM initialization is done and
before S3 boot script is executed, this GUID is installed as PPI in
PEI and protocol in SMM environment. It allows for PEIMs or SMM
drivers to hook this point and do the required tasks.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Albecki, Mateusz
Wei6 Xu
Chu, Maggie
Zhang, Chao B
Anthony PERARD
Liming Gao
Dandan Bi
Bret Barkelew
Zhichao Gao
Ard Biesheuvel
Michael D Kinney
Chen A Chen
Hao Wu
Marcin Wojtas
Tomasz Michalec
Star Zeng
Fu Siyuan
Ruiyu Ni
Eric Dong
Heyi Guo