Remove the support that permits calls into the MM context to dispatch
firmware volumes that are not part of the initial standalone MM firmware
volume.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: Achin Gupta <achin.gupta@arm.com>
Instead of deferring dispatch of the remaining MM drivers once the
CPU driver has been dispatched, proceed and dispatch all drivers.
This makes sense for standalone MM, since all dispatchable drivers
should be present in the initial firmware volume anyway: dispatch
of additional FVs originating in the non-secure side is not supported.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: Achin Gupta <achin.gupta@arm.com>
Standalone MM requires 4 KB section alignment for all images, so that
strict permissions can be applied. Unfortunately, this results in a
lot of wasted space, which is usually costly in the secure world
environment that standalone MM is expected to operate in.
So let's permit the standalone MM drivers (but not the core) to be
delivered in a compressed firmware volume.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: Achin Gupta <achin.gupta@arm.com>
The dispatcher uses the PE/COFF loader to load images into the heap,
but only does so after copying the entire image first, leading to
two copies being made for no good reason.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Achin Gupta <achin.gupta@arm.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Management Mode (MM) is a generic term used to describe a secure
execution environment provided by the CPU and related silicon that is
entered when the CPU detects a MMI. For x86 systems, this can be
implemented with System Management Mode (SMM). For ARM systems, this can
be implemented with TrustZone (TZ).
A MMI can be a CPU instruction or interrupt. Upon detection of a MMI, a
CPU will jump to the MM Entry Point and save some portion of its state
(the "save state") such that execution can be resumed.
The MMI can be generated synchronously by software or asynchronously by
a hardware event. Each MMI source can be detected, cleared and disabled.
Some systems provide for special memory (Management Mode RAM or MMRAM)
which is set aside for software running in MM. Usually the MMRAM is
hidden during normal CPU execution, but this is not required. Usually,
after MMRAM is hidden it cannot be exposed until the next system reset.
The MM Core Interface Specification describes three pieces of the PI
Management Mode architecture:
1. MM Dispatch
During DXE, the DXE Foundation works with the MM Foundation to
schedule MM drivers for execution in the discovered firmware volumes.
2. MM Initialization
MM related code opens MMRAM, creates the MMRAM memory map, and
launches the MM Foundation, which provides the necessary services to
launch MM-related drivers. Then, sometime before boot, MMRAM is
closed and locked. This piece may be completed during the
SEC, PEI or DXE phases.
3. MMI Management
When an MMI generated, the MM environment is created and then the MMI
sources are detected and MMI handlers called.
This patch implements the MM Core.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>
Signed-off-by: Supreeth Venkatesh <supreeth.venkatesh@arm.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Michael D Kinney
Ard Biesheuvel
Supreeth Venkatesh