The SP805 watchdog driver doesn't implement the PI watchdog protocol
fully, but always simply resets the system if the watchdog time runs
out.
However, the hardware does support the intended usage model, as long
as the SP805 is wired up correctly. So let's implement interrupt based
mode involving a handler that is registered by the DXE core and invoked
when the watchdog runs out. In the interrupt handler, we invoke the
notify function if one was registered, before calling the ResetSystem()
runtime service (as per the UEFI spec)
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Before fixing the SP805 driver, let's clean it up a bit. No
functional changes.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Currently, each flash bank controlled by ArmPlatformPkg/NorFlashDxe
has its own VendorHw GUID, and instances of NorFlashPlatformLib
describe each bank to the driver, along with the GUID for each.
This works ok for bare metal platforms, but it would be useful for
virtual platforms if we could obtain this information from a
device tree, which would require us to invent GUIDs on the fly,
given that the 'cfi-flash' binding does not include a GUID.
So instead, let's switch to a single GUID for all flash banks,
and update the driver's device path handling to include an index
to identify each bank uniquely.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Thomas Abraham <thomas.abraham@arm.com>
A subsequent patch will change the layout of devicepath nodes
produced by this driver. In preparation, make some tweaks to
the code to use a packed struct for the devicepath and to pass
the device index to NorFlashCreateInstance(). These are cosmetic
changes only, the resulting binaries should be identical.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Thomas Abraham <thomas.abraham@arm.com>
There is no functional modification in this change
some comments are modified and a few new comments are added.
This is to prevent mixing formatting changes with functional
changes.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
There is no functional modification in this change
As preparation for further work, the formatting is corrected to meet
the EDKII coding standard.
Of specific note, some invalid include guards were fixed.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
NorFlashFvbInitialize() calls gDS->SetMemorySpaceAttributes() to mark the
varstore flash region as uncached. This DXE service depends on the CPU
Architectural protocol, and the DXE core is allowed to return
EFI_NOT_AVAILABLE_YET if it hasn't dispatched ArmPkg/Drivers/CpuDxe
earlier. Make the dependency explicit.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Supreeth Venkatesh <Supreeth.Venkatesh@arm.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The BEFORE depex opcode that we currently use to force ourselves in front
of the variable driver cannot be combined with other depex opcodes.
Replace the depex with TRUE, and signal NvVarStoreFormattedLib through the
installation of "gEdkiiNvVarStoreFormattedGuid".
Platforms that rely on NorFlashDxe to format the variable store (as
opposed to formatting a variable store template through an FDF file, as
part of the build) should hook NvVarStoreFormattedLib into the variable
drivers they use, so that the latter await our cue.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Supreeth Venkatesh <Supreeth.Venkatesh@arm.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The lazy initialization of the varstore FVB makes no longer sense at this
point:
- "mNorFlashInstanceTemplate.Initialize" is NULL;
- in NorFlashCreateInstance(), we only set Instance->Initialize to
non-NULL -- namely NorFlashFvbInitialize() -- if the FVB stands for the
variable store (see "ContainVariableStorage" / "SupportFvb");
- we call Instance->Initialize() from three places:
- from NorFlashWriteSingleBlock(), which is too late for the variable
read service ("variable write" depends on "variable read");
- from InitializeFvAndVariableStoreHeaders(), but that is only reachable
from NorFlashFvbInitialize(), i.e. recursively from
Instance->Initialize() itself;
- and from FvbRead(), which is never called by the variable driver, only
by the FTW driver. However, the variable driver may read (not write)
the memory-mapped varstore flash chip before the FTW driver is
dispatched.
Therefore the lazy initialization is both superfluous and insufficient.
Initialize the varstore headers eagerly, before we install the FVB
protocol interface.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Supreeth Venkatesh <Supreeth.Venkatesh@arm.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Now that LcdGraphicsOutputDxe has been refactored, remove the old code
that is no longer used.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Create a new LcdGraphicsOutputDxe driver from the existing sources that
takes its hardware abstractions from a LcdHwLib library instance rather
than from a .c file linked directly. All we need is a new .inf file, and
a minimal tweak to LcdGraphicsOutputDxe.h to reuse the LcdHwlib prototypes
rather than open code them.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
[ardb: add it to ArmPlatformPkg.dsc so we can build test it standalone]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
None of the platforms we support use these so remove them.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This driver is no longer used anywhere so remove it.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This driver is not used by any platforms so remove it.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Remove PL34xDmc driver which is not used by any platforms
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
No platform uses this so remove it.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
No platforms use this driver so remove it.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The HdLcd.h and PL111Lcd.h header files are internal headers that should
not be used by other drivers. So move them from Include/Drivers into the
driver directory instead.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Remove the PL011UartLib implementation that has been superseded by
the one under Library/
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The two instantiations of LcdGraphicsOutputDxe reference VExpressPkg.dec
without actually relying on anything it defines. In preparation of
moving out VExpressPkg into edk2-platforms, drop these references so we
can keep LcdGraphicsOutputDxe in EDK2.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Move the internal SP805 watchdog header file into the driver directory.
It shouldn't be referenced directly by other modules anyway.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Move the internal PL061 GPIO header file into the driver directory.
It shouldn't be referenced directly by other modules anyway.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
ZTE/SanChip version pl011 has different reg offset and bit offset
for some registers.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
According to the PI spec, Volume 3,
EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL.EraseBlocks():
> The variable argument list is a list of tuples. Each tuple describes a
> range of LBAs to erase and consists of the following:
> * An EFI_LBA that indicates the starting LBA
> * A UINTN that indicates the number of blocks to erase
(NB, in edk2, EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL is a typedef to
EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL.)
In this driver, the NumOfLba local variable is defined with type UINTN,
but the TYPE argument passed to VA_ARG() is UINT32. Fix the mismatch.
In addition, update the DEBUG macro invocation where NumOfLba is formatted
with the %d conversion specifier: UINTN values should be converted to
UINT64 and printed with %Lu or %Lx for portability between 32-bit and
64-bit.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Reported-by: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
When call PL061GetPins() or PL061SetPins(), should use GPIO_PIN_MASK(offset)
as parameter, not offset.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
ARM TZASC-380 IP provides a mechanism to split memory regions being
protected via it into eight equal-sized sub-regions. A bit-setting
allows the corresponding subregion to be disabled.
Several NXP/FSL SoCs support the TZASC-380 IP block and allow
the DDR connected via the TZASC to be partitioned into regions
having different security settings and also allow subregions
to be disabled.
This patch enables this support and can be used for SoCs which
support such a partition of DDR regions.
Details of the 'subregion_disable' register can be viewed here:
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0431c/CHDIGDCI.html
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@nxp.com>
[bhupesh.linux@gmail.com : Added gmail ID as NXP one is no longer valid]
Signed-off-by: Bhupesh Sharma <bhupesh.linux@gmail.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
In NorFlashFvbInitialize() if a valid Firmware Volume header is not found at the
start of NOR Flash, the Flash memory is written before it has been remapped with
EFI_MEMORY_UC attributes to allow write commands. Since the flash memory was
previously mapped with Normal and possibly cacheable memory attributes, the
Flash commands might never reach the device.
This patch fixes this issue by remapping the Flash memory region with correct
memory attributes before writing to it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
When CMD6 & ACMD51 are added into identifying SD process, PL180
should also support CMD6 & ACMD51. Otherwise, it will hang when
system tries to read expected data.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
While most compilers happily allow arithmetic on void pointer,
the RVCT compiler does not, and throws the following warning for
NorFlashDxe:
ArmPlatformPkg/Drivers/NorFlashDxe/NorFlashDxe.c(894,48) :
error #1254-D: arithmetic on pointer to void or function type
Since the expression in question involves a cast from UINTN to VOID*,
simply add some parentheses to eliminate this warning.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Correct some obviously incorrect comments that have invalid details for
the returned values. (Copy /Paste problem?)
There are no functional changes in this commit.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Alexei Fedorov <alexei.fedorov@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This change updates PL011UartInitializePort to compare ReceiveFifoDepth
with the correct hardware FIFO size instead of the constant 32 used
previously.
This corrects a minor bug where a request for a fifo size > 15 and < 32
would not have been honoured on a system with a 16 byte FIFO.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The UEFI spec stipulates that unaligned accesses should be enabled
on CPUs that support them, which means all of them, given that we
no longer support pre-v7 ARM cores, and the AARCH64 bindings mandate
support for unaligned accesses unconditionally.
This means that one should not assume that CopyMem () is safe to call
on regions that may be mapped using device attributes, which is the
case for the NOR flash. Since we have no control over the mappings when
running under the OS, and given that write accesses require device
mappings, we should not call CopyMem () in the read path either, but
use our own implementation that is guaranteed to take alignment into
account.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This module is now identical in functionality to NorFlashDxe, and is no
longer used, so remove it altogether.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Now that the generic Variable Runtime DXE code no longer distinguishes
between gEfiVariableGuid and gEfiAuthenticatedVariableGuid in the varstore
FV header, we can relax the check in the NOR flash driver to accept either
GUID regardless of whether we are running a secure boot capable build or not.
This also means we can always use gEfiAuthenticatedVariableGuid when we
encounter an empty NOR flash that needs to be initialized before use. So
remove the mNorFlashVariableGuid global from the shared code and from both
versions of NorFlashDxe.inf. This essentially collapses the two drivers into
a single one, which means we can remove NorFlashAuthenticatedDxe entirely
in a subsequent patch.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This change corrects 3 problems in the PL011 driver.
1. The TRM states "The UARTLCR_H, UARTIBRD, and UARTFBRD registers must
not be changed:...when the UART is enabled"
2. The TRM (3.3.8) describes logic requiring the UART to be disabled and
flushed before adjusting UARTCR.
3. Several redundant calls get made to PL011UartInitializePort, where
the characteristics do not change, but updating the registers can
cause glitches in the output stream.
The parameters are compared to the current state and no action taken if
no change of state is required.
Where an update is required, the specified logic is followed, and the
register updates only made when the UART is disabled.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
On some platforms the UART clock is not the same for all the serial
ports. The PL011 driver must be capable of handling serial ports with
different clock rates, so must not rely on a PCD for the clock rate.
This patch allows the UART clock rate to be passed as a parameter
to PL011UartInitializePort(), which is called from the serial port
library. This patch also contains the corresponding changes in the
serial port library.
The PCD in Drivers/PL011Uart is replaced by an extra parameter for
PL011UartInitializePort. The PCD is moved to Library/PL011SerialPortLib
to supply the value to pass.
A corresponding patch to ArmVirtPkg is included in the same bundle to
align that with these changes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
The variable LineControl was initialised to zero, then updated in a
condition. This change converts that to a write in each branch of the
condition, removing the Write/Read/Modify/Write sequence.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
The PCDs used in the PL011 UART Driver and Serial Port Library are
inherently "fixed at build". This change updates the source to use
Fixed PCDs for these values. This improves clarity and efficiency.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
This cosmetic change only tidies things up in preparation for actual
updates. (This reflects responses to a previously submitted patch,
which has been split into several discrete changes.)
There are no functional changes in this commit.
Changes comprise:
Minor corrections to comment typos.
Minor formatting mods.
Expansion of function comments.
Remove OUT from UartBase parameter.
Addition of #define for "magic mumbers".
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Support multiple PL061 controllers. If platform gpio driver couldn't be
found, PL061 gpio driver will continue to load PcdPL061GpioBase as the
register base.
It could be compatible with the use case of current PL061 gpio driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
TC2 reads 0x02 for the PL180 ID3 register instead of 0x00 as defined in
the spec.
However, the spec [1] states that the contents of ID3 register represent
the "configuration option of the peripheral" and thus not part of the
Prime Cell identification.
For this patch, we drop checking the value in MCI_PERIPH_ID_REG3.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0172a/index.html
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
If the PL180 fails to probe, issue a warning on debug builds.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
PL180 on TC2 has a dependency on gEfiCpuArchProtocolGuid. Without
adding the dependency, TC2 will crash in the PL180 driver.
This problem has been present since d340ef7 when TC2 stopped booting.
However, it was masked by 300fc77 which prevented PL180 from running on
TC2 due to TC2 using a version on PL180 newer than that documented
publicly.
[1] https://github.com/tianocore/edk2/commit/d340ef7
2014-08-26
ArmPkg/ArmArchTimerLib: Remove non required [depex] and IoLib
[2] https://github.com/tianocore/edk2/commit/300fc77
2015-08-25
ArmPlatformPkg/PL180MciDxe: check PrimeCell ID before initializing
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The PL061 GPIO controller is a bit of an anachronism, and the existing
driver does nothing to hide this - leading to it being very tricky to
read.
Rewrite it to document (in comments and code) what is actually
happening, and fix some bugs in the process.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
PL061Initialize() did not actually do anything other than call
PL061Identify() - so cut out the middle man.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
For whatever reason, every single operation on the PL061 looked for an
"Initialized" flag, and manually called the initialization function if
not set. Move this to a single call on protocol installation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
The copyright statement in PL061Gpio.c would not fit on a normal terminal
screen. Break lines at <= 80 characters.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Problems have been encountered because some of the source files have
execute permission set. This can cause git to report them as changed
when they are checked out onto a file system with inherited permissions.
This has been seen using Cygwin, MinGW and PowerShell Git.
This patch makes no change to source file content, and only aims to
correct the file modes/permissions.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19787 6f19259b-4bc3-4df7-8a09-765794883524
Michael D Kinney
Ard Biesheuvel
Girish Pathak
Laszlo Ersek
Jun Nie
Haojian Zhuang
Bhupesh Sharma
Achin Gupta
Alexei
Evan Lloyd
Ryan Harkin
Leif Lindholm