According to UEFI spec 2.7, PciIo->GetBarAttributes should return host
address (CPU view ddress) rather than device address (PCI view
address), and
device address = host address + address translation offset,
so we subtract translation from device address before returning.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Signed-off-by: Yi Li <phoenix.liyi@huawei.com>
Reviewed-by: Ni Ruiyu <ruiyu.ni@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
According to UEFI spec 2.7, PciRootBridgeIo->Configuration() should
return host address (CPU view ddress) rather than device address
(PCI view address), so in function GetMmioAddressTranslationOffset we
need to convert the range to device address before comparing.
And device address = host address + translation offset.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Signed-off-by: Yi Li <phoenix.liyi@huawei.com>
Reviewed-by: Ni Ruiyu <ruiyu.ni@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
PCI address translation is necessary for some non-x86 platforms. On
such platforms, address value (denoted as "device address" or "address
in PCI view") set to PCI BAR registers in configuration space might be
different from the address which is used by CPU to access the
registers in memory BAR or IO BAR spaces (denoted as "host address" or
"address in CPU view"). The difference between the two addresses is
called "Address Translation Offset" or simply "translation", and can
be represented by "Address Translation Offset" in ACPI QWORD Address
Space Descriptor (Offset 0x1E). However UEFI and ACPI differs on the
definitions of QWORD Address Space Descriptor, and we will follow UEFI
definition on UEFI protocols, such as PCI root bridge IO protocol and
PCI IO protocol. In UEFI 2.7, "Address Translation Offset" is "Offset
to apply to the Starting address to convert it to a PCI address". This
means:
1. Translation = device address - host address.
2. PciRootBridgeIo->Configuration should return CPU view address, as
well as PciIo->GetBarAttributes.
Summary of addresses used in protocol interfaces and internal
implementations:
1. *Only* the following protocol interfaces assume Address is Device
Address:
(1). PciHostBridgeResourceAllocation.GetProposedResources()
Otherwise PCI bus driver cannot set correct address into PCI
BARs.
(2). PciRootBridgeIo.Mem.Read() and PciRootBridgeIo.Mem.Write()
(3). PciRootBridgeIo.CopyMem()
UEFI and PI spec have clear statements for all other protocol
interfaces about the address type.
2. Library interfaces and internal implementation:
(1). Base and Limit in PCI_ROOT_BRIDGE_APERTURE are device address.
It is easy to check whether the address is below 4G or above 4G.
(2). Addresses in PCI_ROOT_BRIDGE_INSTANCE.ResAllocNode are host
address, for they are allocated from GCD.
(3). Address passed to PciHostBridgeResourceConflict is host address,
for it comes from PCI_ROOT_BRIDGE_INSTANCE.ResAllocNode.
RESTRICTION: to simplify the situation, we require the alignment of
Translation must be larger than any BAR alignment in the same root
bridge, so that resource allocation alignment can be applied to both
device address and host address.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Signed-off-by: Yi Li <phoenix.liyi@huawei.com>
Reviewed-by: Ni Ruiyu <ruiyu.ni@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Current BLOCK IO API code is using TPL_CALLBACK,
but comment is saying TPL_NOTIFY.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
When a USB device reports failure for a CMD and REQUEST SENSE returns
Media Changed key, UsbBootExecCmdWithRetry() stops to retry CMD and
returns EFI_MEDIA_CHANGED to caller.
For this case, the CMD should be retried until success, getting
NoMedia sense key or timeout.
The patch updates UsbBootExecCmdWithRetry() to follow the above
rule so EFI_MEDIA_CHANGED is no longer returned.
UsbBootDetectMedia() is updated accordingly.
Because UsbBootGetParams() is called for new plugged USB storage,
and some USB storage devices may report Media Changed key,
UsbBootGetParams() is updated to treat it as a Success.
This change could fix the issue that some USB storage devices
cannot be detected.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This reverts commit a662afb5b0.
* MdeModulePkg/UsbStorage: Fix "map -r" cannot detect media change
The above commit fixed the following issue:
When system boots to Shell without CDROM inside USB CDROM drive,
and then user inserts the CDROM with Eltorito file system,
"map -r" cannot show the new ELtorito file system.
The commit caused EFI_MEDIA_CHANGED status returned from
UsbBootDetectMedia().
But that fix exposes another issue:
When issuing ReadCapacity command to certain USB key
(Kingston DataTraveler G3 8GB) after it's hot-plugged, USB device
returns STALL error and RequestSense command returns media changed
sense data. (Most of the USB keys return SUCCESS for ReadCapacity
command after hot-plug.)
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This reverts commit 6461344c31.
* MdeModulePkg/UsbMass: Fix hot-plug USB CDROM can't be recognized
UsbBootExecCmd() only calls UsbBootRequestSense() to get sense key
when CMD fails.
When POWER ON (29h) ASC returns from REQUEST SENSE, implementation
should retry the CMD, instead of treating this as a SUCCESS.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
In below calling stack:
UsbBootIsUnitReady()
UsbBootExecCmdWithRetry()
UsbBootExecCmd()
UsbBootRequestSense()
When USB CDROM is hot-plugged, UsbBootRequestSense() retrieves sense
key (6 = UnitAttention), additional sense code (29h = Power ON).
But it wrongly maps such sense data to Device Error status.
It causes UsbBootExecCmd() executed again.
In the second time call to UsbBootExecCmd(), UsbBootRequestSense()
retrieves sense key (6 = UnitAttention), additional sense code
(28h = media changed).
The above analysis explains why hot-plug USB CDROM cannot be
recognized after below commit:
SHA1 a662afb5b0
* MdeModulePkg/UsbStorage: Fix "map -r" cannot detect media change,
which removes the media changed status check in UsbBootDetectMedia().
The proper fix to this problem is to map the ASC (additional sense
code 29h) properly to success status so that no second call to
UsbBootExecCmd() is made.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Initialize local variable to suppress warning C4703:
potentially uninitialized local pointer variable.
Both reads (dereferences) of "PciRootBridgeIo" in
PciBusDriverBindingStart() are only reached if
"gFullEnumeration" is TRUE on entry *and* we successfully
open the EfiPciRootBridgeIoProtocol interface.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Today's implementation only return key state when there is key.
But when user doesn't press any key, the key state cannot be
returned.
The patch changes the ReadKeyStrokeEx() to always return the
key state even there is no key pressed.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Today's implementation only return key state when there is key.
But when user doesn't press any key, the key state cannot be
returned.
The patch changes the ReadKeyStrokeEx() to always return the
key state even there is no key pressed.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Invoke the newly introduced SD/MMC override protocol to override
the capabilities register after reading it from the device registers,
and to call the pre/post host init and reset hooks at the appropriate
times.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Within function NvmExpressPassThru():
The data buffer for the below 2 Admin command:
Create I/O Completion Queue command (Opcode 01h)
Create I/O Submission Queue command (Opcode 05h)
are not mapped to the PCI controller specific addresses.
But the current code logic also prevents the below NVM command:
Write (Opcode 01h)
from mapping its data buffer.
Hence, this commit refine the logic to resolve this issue.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Per PI spec, the PciEnumerationComplete protocol installation
should be after PciIo installation.
Today's implementation installs the PciEnumerationComplete
after hardware enumeration is completed, but before PciIo
installation.
The change corrects the spec/implementation gap.
The change also benefits certain implementation that depends on
the PciIo handle in PciEnumerationComplete callback.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The patch is just a code cleanup with no functionality impact.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
When system boots to Shell without CDROM in the USB CDROM drive,
and then user inserts one CDROM with Eltorito file system,
"map -r" cannot show the the new Eltorito file system.
The root cause is when "map" command probes the media change
by calling dummy ReadBlockIo(), UsbMassStorage ReadBlockIo()
contains a bug that ignores the media change status:
UsbBootDetectMedia() ignores the EFI_MEDIA_CHANGED status
returned from UsbBootIsUnitReady(), in consequence, the
BlockIo protocol re-installation logic doesn't run.
By checking the code change history, below commit
SHA-1: 19bc852765
* remove unnecessary retry logic from usb mass storage driver.
adds the code to skip EFI_MEDIA_CHANGED status.
Talking with the original committer Tian Feng, he said the
change was just a code cleanup, not for a special bug fix.
So I revert part of the patch, only keep the change that
removes unnecessary retry logic. It can fix this bug.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
It didn't cause big issues when VT-d was disabled.
But in VT-d enabled platform, lack of EhcFreeUrb call caused
the DMA data was not moved back to user's buffer.
It caused the correct data cannot be got through sync interrupt
transfer.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
EBC compiler doesn't treat EFI_xxx as constant due to these macros
are UINT64 type in 64bit env and UINT32 type in 32bit env.
So it reports error when "case EFI_xxx" is used.
The patch changes to use if-else to fix EBC build failure.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
DUAL_ADDRESS_CYCLE is missing in the EFI_UNSUPPORTED
return status description.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Current code always return EFI_MEDIA_CHANGED no matter the media
is removed from CD/DVD drive or the media is changed.
It doesn't strictly follow the UEFI Spec.
Update code to return EFI_NO_MEDIA when media is removed.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Reviewed-by: Hao A Wu <hao.a.wu@intel.com>
Commit f6b139b added return status handling to PciIo->Mem.Write.
However, the second status handling will override EFI_DEVICE_ERROR
returned in this branch:
//
// Check the NVMe cmd execution result
//
if (Status != EFI_TIMEOUT) {
if ((Cq->Sct == 0) && (Cq->Sc == 0)) {
Status = EFI_SUCCESS;
} else {
Status = EFI_DEVICE_ERROR;
^^^^^^^^^^^^^^^^
Since PciIo->Mem.Write will probably return SUCCESS, it causes
NvmExpressPassThru to return SUCCESS even when DEVICE_ERROR occurs.
Callers of NvmExpressPassThru will then continue executing which may
cause further unexpected results, e.g. DiscoverAllNamespaces couldn't
break out the loop.
So we save previous status before calling PciIo->Mem.Write and restore
the previous one if it already contains error.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This patch caused Windows 10 S4 resume failure.
Considering the similar changes are reverted from PciBus driver,
revert the patch from AtaAtapiPassThru as well.
Revert "MdeModulePkg/AtaAtapiPassThru: disable the device
at ExitBootServices()"
This reverts commit 6fb8ddd36b.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This patch caused Windows 10 S4 resume failure.
Considering the similar changes are reverted from PciBus driver,
revert the patch from AtaAtapiPassThru as well.
Revert "MdeModulePkg/AtaAtapiPassThru: disable only BM-DMA at
ExitBootServices()"
This reverts commit 76fd5a660d.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Update the UhciPei driver to consume IOMMU_PPI to allocate DMA buffer.
If no IOMMU_PPI exists, this driver still calls PEI service to allocate
DMA buffer, with assumption that DRAM==DMA.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
This patch is following 2c656af04d.
1. Fix typo "XHC" to "EHC".
2. Reinitialize Request(Phy/Map) and Data(Phy/Map)
in Urb, otherwise the last time value of them may
be used in error handling when error happens.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
This reverts commit 5db417ed25.
"MdeModulePkg/PciBusDxe: Enable Bus Master on P2P bridges on demand"
We met some compatibility issues when doing Windows S4 resume.
Reverting the BME disabling patches to fix the S4 resume issue.
Signed-off-by: Ruiyu Ni <Ruiyu.ni@intel.com>
Signed-off-by: Michael Turner <michael.turner@microsoft.com>
Cc: Michael D Kinney <Michael.d.kinney@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
This reverts commit 050763db07.
"MdeModulePkg/PciBus: Disable BME of all devices when entering RT"
We met some compatibility issues when doing Windows S4 resume.
Reverting the BME disabling patches to fix the S4 resume issue.
Signed-off-by: Ruiyu Ni <Ruiyu.ni@intel.com>
Signed-off-by: Michael Turner <michael.turner@microsoft.com>
Cc: Michael D Kinney <Michael.d.kinney@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=767
If a USB Mass Storage device does not support the Get
Max LUN command, then the USB I/O Protocol ControlTransfer()
service may return an error. If an error is returned for
this command, then assume that the device does not support
multiple LUNs and return a maximum LUN value of 0.
The USB Mass Storage Class Specification states that a
maximum LUN value larger than 0x0F is invalid. Add
a check to make sure this maximum LUN value is in this
valid range, and if it is not, then assume that the
device does not support multiple LUNs and return a
maximum LUN value of 0.
This change improves compatibility with USB FLASH drives
that do not support the Get Max LUN command or return
an invalid maximum LUN value.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=767
The USB I/O Protocol function ControlTransfer() has a DataLength
parameter that specifies the size of the Data buffer. The
UsbBusDxe module implements the USB I/O Protocol using the
services of the USB2 Host Controller Protocol. The DataLength
parameter in the USB2 Host Controller Protocol ControlTransfer()
service is an IN OUT parameter so the number of bytes actually
transferred is returned. Since the USB I/O Protocol
ControlTransfer() service can not return the number of bytes
actually transferred, the only option if the number of bytes
actually transferred is less than the number of bytes requested
is to return EFI_DEVICE_ERROR.
The change fixes an issue with a USB mass storage device that
responds with 0 bytes to the Get MAX LUN command.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=782
Update the Request Sense check for the Request Sense Key of
USB_BOOT_SENSE_UNIT_ATTENTION. For this Sense Key, the
Additional Sense Key to EFI_STATUS mappings are:
USB_BOOT_ASC_MEDIA_CHANGE -> EFI_MEDIA_CHANGE
USB_BOOT_ASC_NOT_READY -> EFI_NOT_READY
USB_BOOT_ASC_NO_MEDIA -> EFI_NOT_READY
All others -> EFI_DEVICE_ERROR
A USB flash drive is returning Request Sense Key of
USB_BOOT_SENSE_UNIT_ATTENTION and an Additional Sense Key of
USB_BOOT_ASC_NO_MEDIA for a few seconds before returning an
Additional Sense Key of USB_BOOT_ASC_MEDIA_CHANGE.
The current logic treats this initial Request Sense info as an
error and reties the command 5 times before failing completely.
With this change the USB Flash Drive works correctly.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Update the SdBlockIoPei driver to consume IOMMU_PPI to allocate DMA
buffer.
If no IOMMU_PPI exists, this driver still calls PEI service
to allocate DMA buffer, with assumption that DRAM==DMA.
This is a compatible change.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Update the EmmcBlockIoPei driver to consume IOMMU_PPI to allocate DMA
buffer.
If no IOMMU_PPI exists, this driver still calls PEI service
to allocate DMA buffer, with assumption that DRAM==DMA.
This is a compatible change.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
V2 changes:
Resource cleanup logic update in UfsEndOfPei().
V1 history:
Update the UfsBlockIoPei driver to consume IOMMU_PPI to allocate DMA
buffer.
If no IOMMU_PPI exists, this driver still calls PEI service
to allocate DMA buffer, with assumption that DRAM==DMA.
This is a compatible change.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
1. Call IoMmuInit() after locating gPeiUsbControllerPpiGuid.
2. Call XhcPeiFreeSched() to do cleanup in XhcEndOfPei.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
V2: Halt HC at EndOfPei.
Update the EhciPei driver to consume IOMMU_PPI to allocate DMA buffer.
If no IOMMU_PPI exists, this driver still calls PEI service to allocate
DMA buffer, with assumption that DRAM==DMA.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=766
Update logic to not return an error from UsbBootRequestSense()
if a Request Sense command responds with no sense information.
It is legal for a USB mass storage device to respond to a
Request Sense command with a SenseKey of
USB_BOOT_SENSE_NO_SENSE and an Additional Sense
Code of USB_BOOT_ASC_NO_ADDITIONAL_SENSE_INFORMATION.
This is described in Section 3.3 of the Universal Serial
Bus Mass Storage Specification For Bootability:
http://www.usb.org/developers/docs/devclass_docs/usb_msc_boot_1.0.pdf
The previous logic returned an error of EFI_NO_RESPONSE
and this caused USB mass storage devices such as a USB
floppy drive to not be detected.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
For PciIoPciRead interface, memory prior to Buffer would be written
with zeros if Offset was larger than sizeof (Dev->ConfigSpace), which
would cause serious system exception.
So we add a pre-check branch to avoid memory override.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The patch ensures all DMA transactions are blocked after
ExitBootService.
If a platform enables IOMMU before and needs disable IOMMU after
ExitBootService, the IOMMU should be disabled after PCI bus driver
disables BME.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Michael Turner <michael.turner@microsoft.com>
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jeff Fan <vanjeff_919@hotmail.com>
Currently, we complete a synchronous operation without unmapping the
DMA mappings, and free the pages using FreePages () rather than calling
EFI_PCI_IO_PROTOCOL::FreeBuffer. This is simply incorrect, but it also
breaks non-coherent DMA as well as DMA protection and/or memory encryption
so let's do it correctly and call SdMmcFreeTrb() instead.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
It's a regression of below commit:
SHA-1: 8be37a5cee
* MdeModulePkg/SecurityStubDxe: Defer 3rd party image before EndOfDxe
When PciBus driver fails to load the Option ROM, it doesn't produce
BusOverride protocol. It was a correct behavior before the above
commit. But due to the above commit, BusOverride protocol never is
produced by PciBus driver.
The patch fixes this issue using the following solution:
1. PciBus records the image device path when LoadImage fails.
2. Override.GetDriver() tries to look for the image handle using
the stored image device path.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The patch shouldn't impact functionality.
Original code records the ImageHandle of Option ROM by creating a
new entry. It's not necessary.
The patch updates the ImageHandle in the old entry.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The patch doesn't impact real functionality.
It only renames EFI_PCI_ROM_IMAGE_MAPPING to PCI_ROM_IMAGE,
and changes prototype of PciRomAddImageMapping so that
no explicit type cast is needed when calling this function.
It also removes unused field RomBase from PCI_IO_DEVICE structure.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Clearing I/O port decoding in the PCI command register at
ExitBootServices() breaks IDE boot in Windows, on QEMU's "pc" (i440fx)
machine type. (AHCI boot on "q35" is unaffected.) Windows seems repeatedly
stuck, apparently waiting for a timeout of sorts.
This is arguably a Windows bug; a native OS driver should not expect the
firmware to leave the PCI command register in any particular state.
Strictly speaking, we only need to disable BM-DMA at ExitBootServices(),
in order to abort pending transfers to/from RAM, which is soon to be owned
by the OS. BM-DMA is also the only bit that's explicitly named by the UEFI
Driver Writers' Guide, for clearing at ExitBootServices().
I've verified that clearing only BM-DMA fixes the issue (boot time) on
i440fx, and does not regress q35/AHCI.
Cc: Aleksei Kovura <alex3kov@zoho.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Dann Frazier <dannf@ubuntu.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Reported-by: Aleksei Kovura <alex3kov@zoho.com>
Reported-by: Dann Frazier <dannf@ubuntu.com>
Reported-by: https://launchpad.net/~cjkrupp
Bisected-by: Dann Frazier <dannf@ubuntu.com>
Bisected-by: https://launchpad.net/~cjkrupp
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Suggested-by: Star Zeng <star.zeng@intel.com>
Ref: https://bugs.launchpad.net/ubuntu/+source/edk2/+bug/1725560
Fixes: 6fb8ddd36b
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Tested-by: Aleksei Kovura <alex3kov@zoho.com>
The bug was caused by 728d74973c
"MdeModulePkg/PciBus: Count multiple hotplug resource paddings".
The patch firstly updated the Bridge->Alignment to the maximum
alignment of all devices under the bridge, then aligned the
Bridge->Length to Bridge->Alignment.
It caused too much resources were claimed.
The new patch firstly aligns Bridge->Length to Bridge->Alignment,
then updates the Bridge->Alignment to the maximum alignment of all
devices under the bridge.
Because the step to update the Bridge->Alignment is to make sure
the resource allocated to the bus under the Bridge meets all
devices alignment. But the Bridge->Length doesn't have to align
to the maximum alignment.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Heyi Guo
Star Zeng
Ruiyu Ni
Dandan Bi
Ard Biesheuvel
Hao Wu
Michael D Kinney
Laszlo Ersek