In Intel datasheet 316966-002 (the "q35 spec"), Table 5-1 "DRAM Controller
Register Address Map (D0:F0)" leaves the byte register at config space
offset 0x9C unused.
On QEMU's Q35 board, for detecting the "SMRAM at default SMBASE" feature,
firmware is expected to write MCH_DEFAULT_SMBASE_QUERY (0xFF) to offset
MCH_DEFAULT_SMBASE_CTL (0x9C), and read back the register. If the value is
MCH_DEFAULT_SMBASE_IN_RAM (0x01), then the feature is available, and the
range mentioned below is open (accessible to code running outside of SMM).
Then, once firmware writes MCH_DEFAULT_SMBASE_LCK (0x02) to the register,
the MCH_DEFAULT_SMBASE_SIZE (128KB) range at 0x3_0000 (SMM_DEFAULT_SMBASE)
gets closed and locked down, and the register becomes read-only. The area
is reopened, and the register becomes read/write, at platform reset.
Add the above-listed macros to "Q35MchIch9.h".
(There are some other unused offsets in Table 5-1; for example we had
scavenged 0x50 for implementing the extended TSEG feature. 0x9C is the
first byte-wide register standing in isolation after 0x50.)
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1512
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Message-Id: <20200129214412.2361-4-lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
In a subsequent patch, we'll introduce new DRAM controller macros in
"Q35MchIch9.h". Their names are too long for the currently available
vertical whitespace, so increase the latter first.
There is no functional change in this patch ("git show -b" displays
nothing).
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1512
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Message-Id: <20200129214412.2361-3-lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
In v1.5.0, QEMU's "pc" (i440fx) board gained a "CPU present bitmap"
register block. In v2.0.0, this was extended to the "q35" board.
In v2.7.0, a new (read/write) register interface was laid over the "CPU
present bitmap", with an option for the guest to switch the register block
to the new (a.k.a. modern) interface.
Both interfaces are documented in "docs/specs/acpi_cpu_hotplug.txt" in the
QEMU tree.
Add macros for a minimal subset of the modern interface, just so we can
count the possible CPUs (as opposed to boot CPUs) in a later patch in this
series.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1515
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20191022221554.14963-3-lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The informations to make a XENMEM_memory_map hypercall is copied over
from the public header of the Xen Project, with the type name modified
to build on OVMF.
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1689
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190813113119.14804-22-anthony.perard@citrix.com>
Allow to use Xen hypercalls earlier, during the PEIM stage, but
XenHypercallLibInit() must be called once the XenInfo HOB is created
with the HyperPage setup.
Change the return value of XenHypercallLibInit so failure can be
detected when the call shouldn't fail, but still have the constructor
always succeed.
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1689
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190813113119.14804-17-anthony.perard@citrix.com>
The purpose of XenPlatformLib is to regroup the few functions that are
used in several places to detect if Xen is detected, and to get the
XenInfo HOB.
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1689
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190813113119.14804-14-anthony.perard@citrix.com>
Check if there's a start of the day struct provided to PVH guest, save
the ACPI RSDP address for later.
This patch import import arch-x86/hvm/start_info.h from xen.git.
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1689
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190813113119.14804-13-anthony.perard@citrix.com>
EFI_XEN_OVMF_INFO is only useful to retrieve the E820 table. The
mXenHvmloaderInfo isn't used yet, but will be use in a further patch to
retrieve the E820 table.
Also remove the unused pointer from the XenInfo HOB as that information
is only useful in the XenPlatformPei.
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1689
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190813113119.14804-11-anthony.perard@citrix.com>
For the EnrollDefaultKeys application, the hypervisor is expected to add a
string entry to the "OEM Strings" (Type 11) SMBIOS table, with the
following format:
4e32566d-8e9e-4f52-81d3-5bb9715f9727:<Base64 X509 cert for PK and first KEK>
The string representation of the GUID at the front is the "application
prefix", in terms of QEMU commit
<https://git.qemu.org/?p=qemu.git;a=commit;h=2d6dcbf93fb0>.
Introduce this GUID in the usual manner.
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Julien Grall <julien.grall@arm.com>
Bugzilla: https://bugzilla.tianocore.org/show_bug.cgi?id=1747
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Gary Lin <glin@suse.com>
The GUID
77FA9ABD-0359-4D32-BD60-28F4E78F784B
is specified in MSDN, at
<https://msdn.microsoft.com/en-us/ie/dn932805(v=vs.94)>, therefore it
deserves an entry in the package DEC file, and a header file under
"Include/Guid".
(Arguably, this GUID declaration / definition could even live under
SecurityPkg, but the edk2 tradition has been to hoist GUIDs,
protocols/PPIs, and lib classes from OvmfPkg to a core package only when
dependent C code is added to the core package.)
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Julien Grall <julien.grall@arm.com>
Bugzilla: https://bugzilla.tianocore.org/show_bug.cgi?id=1747
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Gary Lin <glin@suse.com>
The header files under "OvmfPkg/Include/IndustryStandard/Xen" include the
MIT License text. Replace those license blocks with
"SPDX-License-Identifier: MIT" (which refers to
<https://spdx.org/licenses/MIT.html>) for easier parsing by machines (and
humans).
This follows the tree-wide adoption of "SPDX-License-Identifier"s, made
for <https://bugzilla.tianocore.org/show_bug.cgi?id=1373>.
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Julien Grall <julien.grall@arm.com>
Cc: Lars Kurth <lars.kurth@citrix.com>
Cc: xen-devel@lists.xenproject.org
Bugzilla: https://bugzilla.tianocore.org/show_bug.cgi?id=1654
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1496
This commit copies the exact Legacy8259 protocol header file from
IntelFrameworkPkg to OvmfPkg. Also, the protocol GUID definition is
duplicated in the OvmfPkg DEC file.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Ray Ni <ray.ni@intel.com>
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Introduce the Platform Boot Manager Print Status Code Library (for short,
PlatformBmPrintScLib) class for catching and printing the LoadImage() /
StartImage() preparations, and return statuses, that are reported by
UefiBootManagerLib.
In the primary library instance, catch only such status codes that
UefiBootManagerLib reports from the same module that contains
PlatformBmPrintScLib. The intent is to establish a reporting-printing
channel within BdsDxe, between UefiBootManagerLib and
PlatformBmPrintScLib. Ignore status codes originating elsewhence, e.g.
from UiApp's copy of UefiBootManagerLib.
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Julien Grall <julien.grall@linaro.org>
Cc: Ray Ni <ray.ni@intel.com>
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1515418
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
This reverts commit 328409ce8d, reapplying
9bcca53fe4.
Note that the commit now being reverted is technically correct; the only
reason we're reverting it is because it should not have been pushed past
the Soft Feature Freeze for the edk2-stable201811 tag.
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Julien Grall <julien.grall@linaro.org>
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Cc: yuchenlin <yuchenlin@synology.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1319
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: yuchenlin <yuchenlin@synology.com>
Replace the manual capability list parsing in OvmfPkg/Virtio10Dxe with
PciCapLib and PciCapPciIoLib API calls.
The VIRTIO_PCI_CAP_LINK structure type is now superfluous. (Well, it
always has been; we should have used EFI_PCI_CAPABILITY_HDR.)
Also, EFI_PCI_CAPABILITY_VENDOR_HDR is now included at the front of
VIRTIO_PCI_CAP. No driver other than Virtio10Dxe relies on VIRTIO_PCI_CAP.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Add a library class, and a UEFI_DRIVER lib instance, that are layered on
top of PciCapLib, and allow clients to plug an EFI_PCI_IO_PROTOCOL backend
into PciCapLib, for config space access.
(Side note:
Although the UEFI spec says that EFI_PCI_IO_PROTOCOL_CONFIG() returns
EFI_UNSUPPORTED if "[t]he address range specified by Offset, Width, and
Count is not valid for the PCI configuration header of the PCI
controller", this patch doesn't directly document the EFI_UNSUPPORTED
error code, for ProtoDevTransferConfig() and its callers
ProtoDevReadConfig() and ProtoDevWriteConfig(). Instead, the patch refers
to "unspecified error codes". The reason is that in edk2, the
PciIoConfigRead() and PciIoConfigWrite() functions [1] can also return
EFI_INVALID_PARAMETER for the above situation.
Namely, PciIoConfigRead() and PciIoConfigWrite() first call
PciIoVerifyConfigAccess(), which indeed produces the standard
EFI_UNSUPPORTED error code, if the device's config space is exceeded.
However, if PciIoVerifyConfigAccess() passes, and we reach
RootBridgeIoPciRead() and RootBridgeIoPciWrite() [2], then
RootBridgeIoCheckParameter() can still fail, e.g. if the root bridge
doesn't support extended config space (see commit 014b472053).
For all kinds of Limit violations in IO, MMIO, and config space,
RootBridgeIoCheckParameter() returns EFI_INVALID_PARAMETER, not
EFI_UNSUPPORTED. That error code is then propagated up to, and out of,
PciIoConfigRead() and PciIoConfigWrite().
[1] MdeModulePkg/Bus/Pci/PciBusDxe/PciIo.c
[2] MdeModulePkg/Bus/Pci/PciHostBridgeDxe/PciRootBridgeIo.c
)
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Add a library class, and a BASE lib instance, that are layered on top of
PciCapLib, and allow clients to plug a PciSegmentLib backend into
PciCapLib, for config space access.
(Side note:
The "MaxDomain" parameter is provided because, in practice, platforms
exist where a PCI Express device may show up on a root bridge such that
the root bridge doesn't support access to extended config space. Earlier
the same issue was handled for MdeModulePkg/PciHostBridgeDxe in commit
014b472053. However, that solution does not apply to the PciSegmentLib
class, because:
(1) The config space accessor functions of the PciSegmentLib class, such
as PciSegmentReadBuffer(), have no way of informing the caller whether
access to extended config space actually succeeds.
(For example, in the UefiPciSegmentLibPciRootBridgeIo instace, which
could in theory benefit from commit 014b472053, the
EFI_PCI_ROOT_BRIDGE_IO_PROTOCOL.Pci.Read() status code is explicitly
ignored, because there's no way for the lib instance to propagate it
to the PciSegmentLib caller. If the
EFI_PCI_ROOT_BRIDGE_IO_PROTOCOL.Pci.Read() call fails, then
DxePciSegmentLibPciRootBridgeIoReadWorker() returns Data with
indeterminate value.)
(2) There is no *general* way for any firmware platform to provide, or
use, a PciSegmentLib instance in which access to extended config space
always succeeds.
In brief, on a platform where config space may be limited to 256 bytes,
access to extended config space through PciSegmentLib may invoke undefined
behavior; therefore PciCapPciSegmentLib must give platforms a way to
prevent such access.)
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Add a library class, and a BASE lib instance, to work more easily with PCI
capabilities in PCI config space. Functions are provided to parse
capabilities lists, and to locate, describe, read and write capabilities.
PCI config space access is abstracted away.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Suggested-by: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Add some common macros and type definitions corresponding to the QEMU
TPM interface.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
BLOCK_MMIO_PROTOCOL and BlockMmioToBlockIoDxe were introduced to OvmfPkg
in March 2010, in adjacent commits b0f5144676 and efd82c5794. In the
past eight years, no driver or application seems to have materialized that
produced BLOCK_MMIO_PROTOCOL instances. Meanwhile the UEFI spec has
developed the EFI_RAM_DISK_PROTOCOL, which edk2 implements (and OVMF
includes) as RamDiskDxe.
Rather than fixing issues in the unused BlockMmioToBlockIoDxe driver,
remove the driver, together with the BLOCK_MMIO_PROTOCOL definition that
now becomes unused too.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Steven Shi <steven.shi@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=926
Reported-by: Steven Shi <steven.shi@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
QemuBootOrderLib expects PlatformBootManagerLib to call the following
triplet:
(1) EfiBootManagerConnectAll(),
(2) EfiBootManagerRefreshAllBootOption(),
(3) SetBootOrderFromQemu().
This leads to bad performance, when many devices exist such that the
firmware can drive them, but they aren't marked for booting in the
"bootorder" fw_cfg file. Namely,
(1) EfiBootManagerConnectAll() talks to all hardware, which takes long.
Plus some DriverBindingStart() functions write NV variables, which is
also slow. (For example, the IP config policy for each NIC is stored
in an NV var that is named after the MAC).
(2) EfiBootManagerRefreshAllBootOption() generates boot options from the
protocol instances produced by (1). Writing boot options is slow.
(3) Under the above circumstances, SetBootOrderFromQemu() removes most of
the boot options produced by (2). Erasing boot options is slow.
Introduce ConnectDevicesFromQemu() as a replacement for (1): only connect
devices that the QEMU user actually wants to boot off of.
(There's a slight loss of compatibility when a platform switches from
EfiBootManagerConnectAll() to ConnectDevicesFromQemu().
EfiBootManagerConnectAll() may produce UEFI device paths that are unknown
to QemuBootOrderLib (that is, for neither PCI- nor virtio-mmio-based
devices). The BootOrderComplete() function lets such unmatched boot
options survive at the end of the boot order. With
ConnectDevicesFromQemu(), these options will not be auto-generated in the
first place. They may still be produced by other means.
SetBootOrderFromQemu() is not modified in any way; reordering+filtering
boot options remains a separate task.)
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Shannon Zhao <zhaoshenglong@huawei.com>
Cc: Xiang Zheng <xiang.zheng@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> # ArmVirtQemu
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Xiang Zheng <xiang.zheng@linaro.org>
In the next three patches, we're going to modify three modules under
OvmfPkg. When OVMF is built with -D SMM_REQUIRE and runs in an SEV guest,
each affected module will have to know the page range that covers the
initial (pre-SMBASE relocation) SMRAM save state map. Add a helper
function to MemEncryptSevLib that calculates the "base address" and
"number of pages" constants for this page range.
(In a RELEASE build -- i.e., with assertions disabled and optimization
enabled --, the helper function can be compiled to store two constants
determined at compile time.)
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
The declaration and the definition(s) of the function should have
identical leading comments and/or identical parameter lists. Replace any
leftover "clear" references to the C-bit with "set" references. Also
remove any excess space in the comment block, and unindent the trailing
"**/" if necessary. Correct several parameter references.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
The declaration and the definition(s) of the function should have
identical leading comments and/or identical parameter lists. Also remove
any excess space in the comment block, and unindent the trailing "**/" if
necessary. Correct several parameter references.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
The declaration and the definition(s) of the function should have
identical leading comments and/or identical parameter lists. Also remove
any excess space in the comment block, and unindent the trailing "**/" if
necessary.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
There are many overlong lines; it's hard to work with the library like
this. Rewrap all files to 79 columns.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
QEMU has recently gained the ability to provide various hints about its
PCI bridges. The hints take the form of vendor-specific PCI capabilities.
Define macros and types under "OvmfPkg/Include/IndustryStandard" to
describe these capabilities.
The definitions correspond to "docs/pcie_pci_bridge.txt" in the QEMU tree.
Said documentation was added in the last commit of the following series:
a35fe226558a hw/pci: introduce pcie-pci-bridge device
70e1ee59bb94 hw/pci: introduce bridge-only vendor-specific capability to
provide some hints to firmware
226263fb5cda hw/pci: add QEMU-specific PCI capability to the Generic PCI
Express Root Port
c1800a162765 docs: update documentation considering PCIE-PCI bridge
We are going to parse the Resource Reservation Capability in
OvmfPkg/PciHotPlugInitDxe, and return the reservation requests to
PciBusDxe.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
* Introduce the PIIX4_PAM* and MCH_PAM* macros under
"OvmfPkg/Include/IndustryStandard". These macros capture the PAM
register offsets (in PCI config space) on the respective Memory
Controller B/D/F, from the respective data sheets.
* Under IndustryStandard, introduce the PMC_REGISTER_PIIX4() macro for
PIIX4. (For Q35, we already have DRAMC_REGISTER_Q35().) In both cases,
the B/D/F is 0/0/0.
* Under CsmSupportLib, replace the "PAMRegOffset" field (UINT8) in the
PAM_REGISTER_VALUE structure with "PAMRegPciLibAddress" (UINTN). The new
field contains the return value of the PCI_LIB_ADDRESS() macro.
* Under CsmSupportLib, replace the "mRegisterValues440" elements as
follows:
REG_PAMx_OFFSET_440, ReadEnableData, WriteEnableData
-->
PMC_REGISTER_PIIX4 (PIIX4_PAMx), ReadEnableData, WriteEnableData
* Under CsmSupportLib, replace the "mRegisterValuesQ35" elements as
follows:
REG_PAMx_OFFSET_Q35, ReadEnableData, WriteEnableData
-->
DRAMC_REGISTER_Q35 (MCH_PAMx), ReadEnableData, WriteEnableData
* Under CsmSupportLib, update the register address calculations as follows
(for all of PciOr8(), PciAnd8() and PciRead8()):
PCI_LIB_ADDRESS (
PAM_PCI_BUS,
PAM_PCI_DEV,
PAM_PCI_FUNC,
mRegisterValues[Index].PAMRegOffset
)
-->
mRegisterValues[Index].PAMRegPciLibAddress
* Under CsmSupportLib, remove the PAM_PCI_* and REG_PAM*_OFFSET_* macros.
Technically speaking, these changes could be split into three patches
(IndustryStandard macro additions, CsmSupportLib code updates,
CsmSupportLib macro removals). However, the patch is not big, and in this
case it is actually helpful to present the code movement / refactoring in
one step, for easier verification.
Cc: Aleksei Kovura <alex3kov@zoho.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Ref: https://bugs.launchpad.net/qemu/+bug/1715700
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Aleksei Kovura <alex3kov@zoho.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
This feature indicates that the device is behind an IOMMU that translates
bus addresses from the device into physical addresses in memory. If this
feature bit is set to 0, then the device emits physical addresses which
are not translated further, even though an IOMMU may be present.
see [1] for more infromation
[1] https://lists.oasis-open.org/archives/virtio-dev/201610/msg00121.html
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
The patch change the "BufferPhysAddr" parameter of VirtioAppendDesc()
from type UINTN to UINT64.
UINTN is appropriate as long as we pass system memory references. After
the introduction of bus master device addresses, that's no longer the case
in general. Should we implement "real" IOMMU support at some point, UINTN
could break in 32-bit builds of OVMF.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
[lersek@redhat.com: clarify commit message]
[lersek@redhat.com: balance parens in VirtioAppendDesc() comment blocks]
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
The VRING buffer is a communication area between guest and hypervisor.
Allocate it using VIRTIO_DEVICE_PROTOCOL.AllocateSharedPages() so that
it can be mapped later with VirtioRingMap() for bi-directional access.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
[lersek@redhat.com: correct typo in VirtioRingInit() comment blocks]
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Add a function to map the ring buffer with BusMasterCommonBuffer so that
ring can be accessed by both guest and hypervisor.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
[lersek@redhat.com: fix typo in commit message]
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
For the case when an IOMMU is used for translating system physical
addresses to DMA bus master addresses, the transport-independent
virtio device drivers will be required to map their VRING areas to
bus addresses with VIRTIO_DEVICE_PROTOCOL.MapSharedBuffer() calls.
- MMIO and legacy virtio transport do not support IOMMU to translate the
addresses hence RingBaseShift will always be set to zero.
- modern virtio transport supports IOMMU to translate the address, in
next patch we will update the Virtio10Dxe to use RingBaseShift offset.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
[lersek@redhat.com: remove commit msg paragraph with VirtioLib reference]
[lersek@redhat.com: fix typo in VIRTIO_SET_QUEUE_ADDRESS comment block]
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
The function can be used for mapping the system physical address to virtio
device address using VIRTIO_DEVICE_PROTOCOL.MapSharedBuffer (). The
function helps with centralizing error handling, and it allows the caller
to pass in constant or other evaluated expressions for NumberOfBytes.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
[lersek@redhat.com: s/This/VirtIo/ in the new function's comment blocks]
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
The patch extends VIRTIO_DEVICE_PROTOCOL to provide the following new
member functions:
- AllocateSharedPages : allocate a memory region suitable for sharing
between guest and hypervisor (e.g ring buffer).
- FreeSharedPages: free the memory allocated using AllocateSharedPages ().
- MapSharedBuffer: map a host address to device address suitable to share
with device for bus master operations.
- UnmapSharedBuffer: unmap the device address obtained through the
MapSharedBuffer().
We're free to extend the protocol structure without changing the protocol
GUID, or bumping any protocol version fields (of which we currently have
none), because VIRTIO_DEVICE_PROTOCOL is internal to edk2 by design --
see the disclaimers in "VirtioDevice.h".
The patch implements Laszlo's recommendation [1].
[1] http://mid.mail-archive.com/841bec5f-6f6e-8b1f-25ba-0fd37a915b72@redhat.com
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Add Secure Encrypted Virtualization (SEV) helper library.
The library provides the routines to:
- set or clear memory encryption bit for a given memory region.
- query whether SEV is enabled.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Jordan Justen <jordan.l.justen@intel.com>
This adds a header file defining symbolic constants for the VMWare SVGA
virtual display device in preparation for supporting it in
QemuVideoDxe.
It is mostly an extract of the file lib/vmware/svga_reg.h from commit
329dd537456f93a806841ec8a8213aed11395def of VMWare's vmware-svga
repository at git://git.code.sf.net/p/vmware-svga/git (See also
http://vmware-svga.sourceforge.net/ )
Only the bare essentials necessary for initialisation, modesetting and
framebuffer access have been kept from the original file; macro names
have been prefixed with VMWARE_SVGA_ instead of SVGA2_, and the enum
definition has been adapted to comply with EDK2 naming conventions.
The original file was released by VMWare under the MIT license, this
has been retained.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Phil Dennis-Jordan <phil@philjordan.eu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Introduce the following APIs:
- QemuFwCfgS3CallWhenBootScriptReady(): central function that registers a
callback function, with a context parameter, for when ACPI S3 Boot
Script opcodes can be produced. This function also allocates reserved
memory for the opcodes to operate upon.
The client module is supposed to produce the boot script fragment in the
callback function.
- QemuFwCfgS3ScriptWriteBytes(), QemuFwCfgS3ScriptReadBytes(),
QemuFwCfgS3ScriptSkipBytes(), QemuFwCfgS3ScriptCheckValue(): helper
functions, available only to the above callback function, for composing
the boot script fragment. QemuFwCfgS3ScriptSkipBytes() can double as a
plain "select" whenever necessary.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=394
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
At this point we're ready to retire QemuFwCfgS3Enabled() from the
QemuFwCfgLib class, together with its implementations in:
- ArmVirtPkg/Library/QemuFwCfgLib/QemuFwCfgLib.c
- OvmfPkg/Library/QemuFwCfgLib/QemuFwCfgLib.c
Extend all modules that call the function with a new QemuFwCfgS3Lib class
dependency. Thanks to the previously added library class, instances, and
class resolutions, we can do this switch now as tightly as possible.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=394
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
This library class will enable driver modules (a) to query whether S3
support was enabled on the QEMU command line, (b) to produce fw_cfg DMA
operations that are to be replayed at S3 resume time.
Declare the library class in OvmfPkg/OvmfPkg.dec, and add the library
class header under OvmfPkg/Include/Library/. At the moment, the only API
we expose is QemuFwCfgS3Enabled(), which we'll first migrate from
QemuFwCfgLib. Further interfaces will be added in later patches.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=394
Suggested-by: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Laszlo Ersek
Leif Lindholm
Anthony PERARD
Hao Wu
Michael D Kinney
yuchenlin
Gerd Hoffmann
Marc-André Lureau
Brijesh Singh
Phil Dennis-Jordan
Dandan Bi