mirror of https://github.com/acidanthera/audk.git
7b7508ad78
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=2198 Typically, an AP is booted using the INIT-SIPI-SIPI sequence. This sequence is intercepted by the hypervisor, which sets the AP's registers to the values requested by the sequence. At that point, the hypervisor can start the AP, which will then begin execution at the appropriate location. Under SEV-ES, AP booting presents some challenges since the hypervisor is not allowed to alter the AP's register state. In this situation, we have to distinguish between the AP's first boot and AP's subsequent boots. First boot: Once the AP's register state has been defined (which is before the guest is first booted) it cannot be altered. Should the hypervisor attempt to alter the register state, the change would be detected by the hardware and the VMRUN instruction would fail. Given this, the first boot for the AP is required to begin execution with this initial register state, which is typically the reset vector. This prevents the BSP from directing the AP startup location through the INIT-SIPI-SIPI sequence. To work around this, the firmware will provide a build time reserved area that can be used as the initial IP value. The hypervisor can extract this location value by checking for the SEV-ES reset block GUID that must be located 48-bytes from the end of the firmware. The format of the SEV-ES reset block area is: 0x00 - 0x01 - SEV-ES Reset IP 0x02 - 0x03 - SEV-ES Reset CS Segment Base[31:16] 0x04 - 0x05 - Size of the SEV-ES reset block 0x06 - 0x15 - SEV-ES Reset Block GUID (00f771de-1a7e-4fcb-890e-68c77e2fb44e) The total size is 22 bytes. Any expansion to this block must be done by adding new values before existing values. The hypervisor will use the IP and CS values obtained from the SEV-ES reset block to set as the AP's initial values. The CS Segment Base represents the upper 16 bits of the CS segment base and must be left shifted by 16 bits to form the complete CS segment base value. Before booting the AP for the first time, the BSP must initialize the SEV-ES reset area. This consists of programming a FAR JMP instruction to the contents of a memory location that is also located in the SEV-ES reset area. The BSP must program the IP and CS values for the FAR JMP based on values drived from the INIT-SIPI-SIPI sequence. Subsequent boots: Again, the hypervisor cannot alter the AP register state, so a method is required to take the AP out of halt state and redirect it to the desired IP location. If it is determined that the AP is running in an SEV-ES guest, then instead of calling CpuSleep(), a VMGEXIT is issued with the AP Reset Hold exit code (0x80000004). The hypervisor will put the AP in a halt state, waiting for an INIT-SIPI-SIPI sequence. Once the sequence is recognized, the hypervisor will resume the AP. At this point the AP must transition from the current 64-bit long mode down to 16-bit real mode and begin executing at the derived location from the INIT-SIPI-SIPI sequence. Another change is around the area of obtaining the (x2)APIC ID during AP startup. During AP startup, the AP can't take a #VC exception before the AP has established a stack. However, the AP stack is set by using the (x2)APIC ID, which is obtained through CPUID instructions. A CPUID instruction will cause a #VC, so a different method must be used. The GHCB protocol supports a method to obtain CPUID information from the hypervisor through the GHCB MSR. This method does not require a stack, so it is used to obtain the necessary CPUID information to determine the (x2)APIC ID. The new 16-bit protected mode GDT entry is used in order to transition from 64-bit long mode down to 16-bit real mode. A new assembler routine is created that takes the AP from 64-bit long mode to 16-bit real mode. This is located under 1MB in memory and transitions from 64-bit long mode to 32-bit compatibility mode to 16-bit protected mode and finally 16-bit real mode. Cc: Eric Dong <eric.dong@intel.com> Cc: Ray Ni <ray.ni@intel.com> Cc: Laszlo Ersek <lersek@redhat.com> Reviewed-by: Eric Dong <eric.dong@intel.com> Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Regression-tested-by: Laszlo Ersek <lersek@redhat.com> |
||
|---|---|---|
| .azurepipelines | ||
| .mergify | ||
| .pytool | ||
| ArmPkg | ||
| ArmPlatformPkg | ||
| ArmVirtPkg | ||
| BaseTools | ||
| Conf | ||
| CryptoPkg | ||
| DynamicTablesPkg | ||
| EmbeddedPkg | ||
| EmulatorPkg | ||
| FatPkg | ||
| FmpDevicePkg | ||
| IntelFsp2Pkg | ||
| IntelFsp2WrapperPkg | ||
| MdeModulePkg | ||
| MdePkg | ||
| NetworkPkg | ||
| OvmfPkg | ||
| PcAtChipsetPkg | ||
| SecurityPkg | ||
| ShellPkg | ||
| SignedCapsulePkg | ||
| SourceLevelDebugPkg | ||
| StandaloneMmPkg | ||
| UefiCpuPkg | ||
| UefiPayloadPkg | ||
| UnitTestFrameworkPkg | ||
| .gitignore | ||
| .gitmodules | ||
| .mailmap | ||
| License-History.txt | ||
| License.txt | ||
| Maintainers.txt | ||
| ReadMe.rst | ||
| edksetup.bat | ||
| edksetup.sh | ||
| pip-requirements.txt | ||
ReadMe.rst
============== EDK II Project ============== A modern, feature-rich, cross-platform firmware development environment for the UEFI and PI specifications from www.uefi.org. Core CI Build Status -------------------- ============================= ================= =============== =================== Host Type & Toolchain Build Status Test Status Code Coverage ============================= ================= =============== =================== Windows_VS2019_ |WindowsCiBuild| |WindowsCiTest| |WindowsCiCoverage| Ubuntu_GCC5_ |UbuntuCiBuild| |UbuntuCiTest| |UbuntuCiCoverage| ============================= ================= =============== =================== `More CI Build information <.pytool/Readme.md>`__ Platform CI Build Status ------------------------ Microsoft Windows VS2019 ```````````````````````` ============================= ================= ============= ============= ============== Toolchain CONFIG DEBUG RELEASE NOOPT ============================= ================= ============= ============= ============== EmulatorPkg_Win_VS2019_ | IA32 |em32d| |em32r| |em32n| | | X64 |em64d| |em64r| |em64n| OvmfPkg_Win_VS2019_ | IA32 |op32d| |op32r| |op32n| | | X64 |op64d| |op64r| |op64n| | | IA32 X64 |op3264d| |op3264r| |op3264n| | | IA32 X64 FULL |op3264fd| |op3264fr| |op3264fn| ============================= ================= ============= ============= ============== Ubuntu 18.04 GCC5 ````````````````` ============================= ================= ============= ============= ============== Toolchain CONFIG DEBUG RELEASE NOOPT ============================= ================= ============= ============= ============== ArmVirtPkg_Ubuntu_GCC5_ | AARCH64 |avAArch64du| |avAArch64ru| |avAArch64nu| | | ARM |avArmdu| |avArmru| |avArmnu| EmulatorPkg_Ubuntu_GCC5_ | IA32 |em32du| |em32ru| |em32nu| | | X64 |em64du| |em64ru| |em64nu| OvmfPkg_Ubuntu_GCC5_ | IA32 |op32du| |op32ru| |op32nu| | | X64 |op64du| |op64ru| |op64nu| | | IA32 X64 |op3264du| |op3264ru| |op3264nu| | | IA32 X64 FULL |op3264fdu| |op3264fru| |op3264fru| ============================= ================= ============= ============= ============== |TCBZ_2668|_ - EmulatorPkg Ubuntu GCC5 Segfaults during execution. |TCBZ_2639|_ - EmulatorPkg Ubuntu GCC5 Segfaults during execution. `More ArmVirtPkg CI Build Information <ArmVirtPkg/PlatformCI/ReadMe.md>`__ `More EmulatorPkg CI Build Information <EmulatorPkg/PlatformCI/ReadMe.md>`__ `More OvmfPkg CI Build Information <OvmfPkg/PlatformCI/ReadMe.md>`__ License Details --------------- The majority of the content in the EDK II open source project uses a `BSD-2-Clause Plus Patent License <License.txt>`__. The EDK II open source project contains the following components that are covered by additional licenses: - `BaseTools/Source/C/LzmaCompress <BaseTools/Source/C/LzmaCompress/LZMA-SDK-README.txt>`__ - `BaseTools/Source/C/VfrCompile/Pccts <BaseTools/Source/C/VfrCompile/Pccts/RIGHTS>`__ - `CryptoPkg\Library\BaseCryptLib\SysCall\inet_pton.c <CryptoPkg\Library\BaseCryptLib\SysCall\inet_pton.c>`__ - `CryptoPkg\Library\Include\crypto\dso_conf.h <https://github.com/openssl/openssl/blob/e2e09d9fba1187f8d6aafaa34d4172f56f1ffb72/LICENSE>`__ - `CryptoPkg\Library\Include\openssl\opensslconf.h <https://github.com/openssl/openssl/blob/e2e09d9fba1187f8d6aafaa34d4172f56f1ffb72/LICENSE>`__ - `EmbeddedPkg/Library/FdtLib <EmbeddedPkg/Library/FdtLib/fdt.c>`__. (EDK II uses BSD License) - `EmbeddedPkg/Include/fdt.h <EmbeddedPkg/Include/fdt.h>`__. (EDK II uses BSD Licence) - `EmbeddedPkg/Include/libfdt.h <EmbeddedPkg/Include/libfdt.h>`__. (EDK II uses BSD License) - `MdeModulePkg/Library/LzmaCustomDecompressLib <MdeModulePkg/Library/LzmaCustomDecompressLib/LZMA-SDK-README.txt>`__ - `OvmfPkg <OvmfPkg/License.txt>`__ The EDK II open source project uses content from upstream projects as git submodules that are covered by additional licenses. - `ArmPkg/Library/ArmSoftFloatLib/berkeley-softfloat-3 <https://github.com/ucb-bar/berkeley-softfloat-3/blob/b64af41c3276f97f0e181920400ee056b9c88037/COPYING.txt>`__ - `BaseTools/Source/C/BrotliCompress/brotli <https://github.com/google/brotli/blob/666c3280cc11dc433c303d79a83d4ffbdd12cc8d/LICENSE>`__ - `CryptoPkg/Library/OpensslLib/openssl <https://github.com/openssl/openssl/blob/e2e09d9fba1187f8d6aafaa34d4172f56f1ffb72/LICENSE>`__ - `MdeModulePkg/Library/BrotliCustomDecompressLib/brotli <https://github.com/google/brotli/blob/666c3280cc11dc433c303d79a83d4ffbdd12cc8d/LICENSE>`__ - `MdeModulePkg/Universal/RegularExpressionDxe/oniguruma <https://github.com/kkos/oniguruma/blob/abfc8ff81df4067f309032467785e06975678f0d/COPYING>`__ - `UnitTestFrameworkPkg/Library/CmockaLib/cmocka <https://git.cryptomilk.org/projects/cmocka.git/tree/COPYING?h=cmocka-1.1.5&id=f5e2cd77c88d9f792562888d2b70c5a396bfbf7a>`__ The EDK II Project is composed of packages. The maintainers for each package are listed in `Maintainers.txt <Maintainers.txt>`__. Resources --------- - `TianoCore <http://www.tianocore.org>`__ - `EDK II <https://github.com/tianocore/tianocore.github.io/wiki/EDK-II>`__ - `Getting Started with EDK II <https://github.com/tianocore/tianocore.github.io/wiki/Getting-Started-with-EDK-II>`__ - `Mailing Lists <https://github.com/tianocore/tianocore.github.io/wiki/Mailing-Lists>`__ - `TianoCore Bugzilla <https://bugzilla.tianocore.org>`__ - `How To Contribute <https://github.com/tianocore/tianocore.github.io/wiki/How-To-Contribute>`__ - `Release Planning <https://github.com/tianocore/tianocore.github.io/wiki/EDK-II-Release-Planning>`__ Code Contributions ------------------ To make a contribution to a TianoCore project, follow these steps. #. Create a change description in the format specified below to use in the source control commit log. #. Your commit message must include your ``Signed-off-by`` signature #. Submit your code to the TianoCore project using the process that the project documents on its web page. If the process is not documented, then submit the code on development email list for the project. #. It is preferred that contributions are submitted using the same copyright license as the base project. When that is not possible, then contributions using the following licenses can be accepted: - BSD (2-clause): http://opensource.org/licenses/BSD-2-Clause - BSD (3-clause): http://opensource.org/licenses/BSD-3-Clause - MIT: http://opensource.org/licenses/MIT - Python-2.0: http://opensource.org/licenses/Python-2.0 - Zlib: http://opensource.org/licenses/Zlib For documentation: - FreeBSD Documentation License https://www.freebsd.org/copyright/freebsd-doc-license.html Contributions of code put into the public domain can also be accepted. Contributions using other licenses might be accepted, but further review will be required. Developer Certificate of Origin ------------------------------- Your change description should use the standard format for a commit message, and must include your ``Signed-off-by`` signature. In order to keep track of who did what, all patches contributed must include a statement that to the best of the contributor's knowledge they have the right to contribute it under the specified license. The test for this is as specified in the `Developer's Certificate of Origin (DCO) 1.1 <https://developercertificate.org/>`__. The contributor certifies compliance by adding a line saying Signed-off-by: Developer Name developer@example.org where ``Developer Name`` is the contributor's real name, and the email address is one the developer is reachable through at the time of contributing. :: Developer's Certificate of Origin 1.1 By making a contribution to this project, I certify that: (a) The contribution was created in whole or in part by me and I have the right to submit it under the open source license indicated in the file; or (b) The contribution is based upon previous work that, to the best of my knowledge, is covered under an appropriate open source license and I have the right under that license to submit that work with modifications, whether created in whole or in part by me, under the same open source license (unless I am permitted to submit under a different license), as indicated in the file; or (c) The contribution was provided directly to me by some other person who certified (a), (b) or (c) and I have not modified it. (d) I understand and agree that this project and the contribution are public and that a record of the contribution (including all personal information I submit with it, including my sign-off) is maintained indefinitely and may be redistributed consistent with this project or the open source license(s) involved. Sample Change Description / Commit Message ------------------------------------------ :: From: Contributor Name <contributor@example.com> Subject: [Repository/Branch PATCH] Pkg-Module: Brief-single-line-summary Full-commit-message Signed-off-by: Contributor Name <contributor@example.com> Notes for sample patch email ```````````````````````````` - The first line of commit message is taken from the email's subject line following ``[Repository/Branch PATCH]``. The remaining portion of the commit message is the email's content. - ``git format-patch`` is one way to create this format Definitions for sample patch email `````````````````````````````````` - ``Repository`` is the identifier of the repository the patch applies. This identifier should only be provided for repositories other than ``edk2``. For example ``edk2-BuildSpecification`` or ``staging``. - ``Branch`` is the identifier of the branch the patch applies. This identifier should only be provided for branches other than ``edk2/master``. For example ``edk2/UDK2015``, ``edk2-BuildSpecification/release/1.27``, or ``staging/edk2-test``. - ``Module`` is a short identifier for the affected code or documentation. For example ``MdePkg``, ``MdeModulePkg/UsbBusDxe``, ``Introduction``, or ``EDK II INF File Format``. - ``Brief-single-line-summary`` is a short summary of the change. - The entire first line should be less than ~70 characters. - ``Full-commit-message`` a verbose multiple line comment describing the change. Each line should be less than ~70 characters. - ``Signed-off-by`` is the contributor's signature identifying them by their real/legal name and their email address. Submodules ---------- Submodule in EDK II is allowed but submodule chain should be avoided as possible as we can. Currently EDK II contains the following submodules - CryptoPkg/Library/OpensslLib/openssl - ArmPkg/Library/ArmSoftFloatLib/berkeley-softfloat-3 - MdeModulePkg/Universal/RegularExpressionDxe/oniguruma - MdeModulePkg/Library/BrotliCustomDecompressLib/brotli - BaseTools/Source/C/BrotliCompress/brotli ArmSoftFloatLib is actually required by OpensslLib. It's inevitable in openssl-1.1.1 (since stable201905) for floating point parameter conversion, but should be dropped once there's no such need in future release of openssl. To get a full, buildable EDK II repository, use following steps of git command .. code-block:: bash git clone https://github.com/tianocore/edk2.git cd edk2 git submodule update --init cd .. If there's update for submodules, use following git commands to get the latest submodules code. .. code-block:: bash cd edk2 git pull git submodule update Note: When cloning submodule repos, '--recursive' option is not recommended. EDK II itself will not use any code/feature from submodules in above submodules. So using '--recursive' adds a dependency on being able to reach servers we do not actually want any code from, as well as needlessly downloading code we will not use. .. =================================================================== .. This is a bunch of directives to make the README file more readable .. =================================================================== .. CoreCI .. _Windows_VS2019: https://dev.azure.com/tianocore/edk2-ci/_build/latest?definitionId=32&branchName=master .. |WindowsCiBuild| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/Windows%20VS2019%20CI?branchName=master .. |WindowsCiTest| image:: https://img.shields.io/azure-devops/tests/tianocore/edk2-ci/32.svg .. |WindowsCiCoverage| image:: https://img.shields.io/badge/coverage-coming_soon-blue .. _Ubuntu_GCC5: https://dev.azure.com/tianocore/edk2-ci/_build/latest?definitionId=31&branchName=master .. |UbuntuCiBuild| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/Ubuntu%20GCC5%20CI?branchName=master .. |UbuntuCiTest| image:: https://img.shields.io/azure-devops/tests/tianocore/edk2-ci/31.svg .. |UbuntuCiCoverage| image:: https://img.shields.io/badge/coverage-coming_soon-blue .. ArmVirtPkg .. _ArmVirtPkg_Ubuntu_GCC5: https://dev.azure.com/tianocore/edk2-ci/_build/latest?definitionId=46&branchName=master .. |avAArch64du| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_ArmVirtPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20QEMU_AARCH64_DEBUG .. |avAArch64ru| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_ArmVirtPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20QEMU_AARCH64_RELEASE .. |avAArch64nu| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_ArmVirtPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20QEMU_AARCH64_NOOPT .. |avArmdu| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_ArmVirtPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20QEMU_ARM_DEBUG .. |avArmru| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_ArmVirtPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20QEMU_ARM_RELEASE .. |avArmnu| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_ArmVirtPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20QEMU_ARM_NOOPT .. EmulatorPkg .. |TCBZ_2668| image:: https://img.shields.io/bugzilla/2668?baseUrl=https%3A%2F%2Fbugzilla.tianocore.org .. _TCBZ_2668: https://bugzilla.tianocore.org/show_bug.cgi?id=2668 .. |TCBZ_2639| image:: https://img.shields.io/bugzilla/2639?baseUrl=https%3A%2F%2Fbugzilla.tianocore.org .. _TCBZ_2639: https://bugzilla.tianocore.org/show_bug.cgi?id=2639 .. _EmulatorPkg_Win_VS2019: https://dev.azure.com/tianocore/edk2-ci/_build/latest?definitionId=44&branchName=master .. _EmulatorPkg_Ubuntu_GCC5: https://dev.azure.com/tianocore/edk2-ci/_build/latest?definitionId=43&branchName=master .. |em32d| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_EmulatorPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20EmulatorPkg_IA32_DEBUG .. |em32du| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_EmulatorPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20EmulatorPkg_IA32_DEBUG .. |em32r| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_EmulatorPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20EmulatorPkg_IA32_RELEASE .. |em32ru| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_EmulatorPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20EmulatorPkg_IA32_RELEASE .. |em32n| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_EmulatorPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20EmulatorPkg_IA32_NOOPT .. |em32nu| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_EmulatorPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20EmulatorPkg_IA32_NOOPT .. |em64d| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_EmulatorPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20EmulatorPkg_X64_DEBUG .. |em64du| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_EmulatorPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20EmulatorPkg_X64_DEBUG .. |em64r| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_EmulatorPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20EmulatorPkg_X64_RELEASE .. |em64ru| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_EmulatorPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20EmulatorPkg_X64_RELEASE .. |em64n| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_EmulatorPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20EmulatorPkg_X64_NOOPT .. |em64nu| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_EmulatorPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20EmulatorPkg_X64_NOOPT .. OvmfPkg .. |TCBZ_2661| image:: https://img.shields.io/bugzilla/2661?baseUrl=https%3A%2F%2Fbugzilla.tianocore.org .. _TCBZ_2661: https://bugzilla.tianocore.org/show_bug.cgi?id=2661 .. _OvmfPkg_Win_VS2019: https://dev.azure.com/tianocore/edk2-ci/_build/latest?definitionId=50&branchName=master .. _OvmfPkg_Ubuntu_GCC5: https://dev.azure.com/tianocore/edk2-ci/_build/latest?definitionId=48&branchName=master .. |op32d| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32_DEBUG .. |op32du| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32_DEBUG .. |op32r| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32_RELEASE .. |op32ru| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32_RELEASE .. |op32n| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32_NOOPT .. |op32nu| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32_NOOPT .. |op64d| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_X64_DEBUG .. |op64du| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_X64_DEBUG .. |op64r| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_X64_RELEASE .. |op64ru| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_X64_RELEASE .. |op64n| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_X64_NOOPT .. |op64nu| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_X64_NOOPT .. |op3264d| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32X64_DEBUG .. |op3264du| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32X64_DEBUG .. |op3264r| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32X64_RELEASE .. |op3264ru| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32X64_RELEASE .. |op3264n| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32X64_NOOPT .. |op3264nu| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32X64_NOOPT .. |op3264fd| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32X64_FULL_DEBUG .. |op3264fdu| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32X64_FULL_DEBUG .. |op3264fr| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Windows_VS2019_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32X64_FULL_RELEASE .. |op3264fru| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32X64_FULL_RELEASE .. |op3264fn| replace:: |TCBZ_2661|_ .. |op3264fnu| image:: https://dev.azure.com/tianocore/edk2-ci/_apis/build/status/PlatformCI_OvmfPkg_Ubuntu_GCC5_CI?branchName=master&jobName=Platform_CI&configuration=Platform_CI%20OVMF_IA32X64_FULL_NOOPT