Currently, the GIC driver has a static dependency on the CPU arch protocol
driver, so it can register its IRQ handler at init time. This means there
is a window between dispatch of the CPU driver and dispatch of the GIC
driver where any unexpected GIC state may trigger an interrupt which we
are not set up to handle yet. Note that this is even the case if we enter
UEFI with interrupts disabled at the CPU, given that any TPL manipulation
involving TPL_HIGH_LEVEL will unconditionally enable IRQs at the CPU side
regardless of whether they were enabled to begin with (but only as soon as
the CPU arch protocol is actually installed)
So let's reorder the GIC driver with the CPU driver, and let it run its
initialization that puts the GIC into a known state before enabling
interrupts. Move its installation of its IRQ handler to a protocol notify
callback on the CPU arch protocol so that it runs as soon as it becomes
available.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
gEfiDebugSupportPeriodicCallbackProtocolGuid and
PcdCpuDxeProduceDebugSupport are referred to from CpuDxe.
Delete references from .inf and .h.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
This module is not used anywhere under edk2 or edk2-platforms, so let's
remove it. This removes the only dependency on ArmPlatformLib from ArmPkg.
While at it, remove a mention of ArmPlatformPkg from a comment in the
.dec file as well.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The existing HardwareInterrupt protocol lacked a means to configure the
level/edge properties of an interrupt. The new HardwareInterrupt2
protocol introduced this capability.
This patch updates the GIC drivers to provide the new interfaces.
The changes comprise:
Update to use HardwareInterrupt2 protocol
Additions to register info in ArmGicLib.h
Added new functionality (GetTriggerType and SetTriggerType)
The requirement for this change derives from a problem detected on ARM
Juno boards, but the change is of generic (ARM) relevance.
This commit is in response to review on the mailing list and, as
suggested there, rolls Girish's updates onto Ard's original example.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Girish Pathak <girish.pathak@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Tested-by: Girish Pathak <girish.pathak@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Even though RELEASE builds produce some diagnostics when a crash
occurs, they can be rather unhelpful:
Synchronous Exception at 0x0000000000000000
and sometimes, it would be useful to get a full register dump from
a production machine without having to modify the firmware.
This can be achieved very easily by incorporating a DEBUG build of
ARM's DefaultExceptionHandlerLib into a DXE driver, and registering
its DefaultExceptionHandler entry point as the synchronous exception
handler, overriding the default one. If we then build this driver
using the UefiDebugLibConOut DebugLib implementation, we end up
with a module than can simply be loaded via the Shell on any system.
Shell> load fs0:ArmCrashDumpDxe.efi
As a bonus, the crash dump will also appear on the graphical display,
not only on the serial port.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Some memory attributes are implied by the memory type, e.g., device memory
is always mapped non-executable and cached memory should have the inner
shareable attribute.
In order to prevent unnecessary memory attribute updates of mappings
created early on, make EfiAttributeToArmAttribute() return these implied
attributes in the same way as ArmMmuLib does already. This avoids false
positives when looking for differences between current and desired mapping
attributes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
We no longer make use of the ArmMmuLib 'feature' to create aliased
memory ranges with mismatched attributes, and in fact, it was only
wired up in the ARM version to begin with.
So remove the VirtualMask argument from ArmSetMemoryAttributes()'s
prototype, and remove the dead code that referred to it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
... where it belongs, since AARCH64 already keeps it there, and
non DXE users of ArmMmuLib (such as DxeIpl, for the non-executable
stack) may need its functionality as well.
While at it, rename SetMemoryAttributes to ArmSetMemoryAttributes,
and make any functions that are not exported STATIC. Also, replace
an explicit gBS->AllocatePages() call [which is DXE specific] with
MemoryAllocationLib::AllocatePages().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Enable the use of strict memory permissions on ARM by processing the
EFI_MEMORY_RO and EFI_MEMORY_XP rather than ignoring them. As before,
calls to CpuArchProtocol::SetMemoryAttributes that only set RO/XP
bits will preserve the cacheability attributes. Permissions attributes
are not preserved when setting the memory type only: the way the memory
permission attributes are defined does not allows for that, and so this
situation does not deviate from other architectures.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Page and section entries in the page tables are updated using the
helper ArmUpdateTranslationTableEntry(), which cleans the page
table entry to the PoC, and invalidates the TLB entry covering
the page described by the entry being updated.
Since we may be updating section entries, we might be leaving stale
TLB entries at this point (for all pages in the section except the
first one), which will be invalidated wholesale at the end of
SetMemoryAttributes(). At that point, all caches are cleaned *and*
invalidated as well.
This cache maintenance is costly and unnecessary. The TLB maintenance
is only necessary if we updated any section entries, since any page
by page entries that have been updated will have been invalidated
individually by ArmUpdateTranslationTableEntry().
So drop the clean/invalidate of the caches, and only perform the
full TLB flush if UpdateSectionEntries() was called, or if sections
were split by UpdatePageEntries(). Finally, make the cache maintenance
on the remapped regions themselves conditional on whether any memory
type attributes were modified.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Currently, any range passed to CpuArchProtocol::SetMemoryAttributes is
fully broken down into page mappings if the start or the size of the
region happens to be misaliged relative to the section size of 1 MB.
This is going to result in memory being wasted on second level page tables
when we enable strict memory permissions, given that we remap the entire
RAM space non-executable (modulo the code bits) when the CpuArchProtocol
is installed.
So refactor the code to iterate over the range in a way that ensures
that all naturally aligned section sized subregions are not broken up.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
To prevent the initial MMU->GCD memory space map synchronization from
stripping permissions attributes [which we cannot use in the GCD memory
space map, unfortunately], implement the same approach as x86, and ignore
SetMemoryAttributes() calls during the time SyncCacheConfig() is in
progress. This is a horrible hack, but is currently the only way we can
implement strict permissions on arbitrary memory regions [as opposed to
PE/COFF text/data sections only]
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Virtual uncached pages are simply pages that are aliased using mismatched
attributes, which is not allowed by the ARM architecture. So remove the
protocol and its implementation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Since the new DXE page protection for PE/COFF images may invoke
EFI_CPU_ARCH_PROTOCOL.SetMemoryAttributes() with only permission
attributes set, add support for this in the AARCH64 MMU code.
Move the EFI_MEMORY_CACHETYPE_MASK macro to a shared location between
CpuDxe and ArmMmuLib so we don't have to introduce yet another
definition.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Currently, we have not implemented support on 32-bit ARM for managing
permission bits in the page tables. Since the new DXE page protection
for PE/COFF images may invoke EFI_CPU_ARCH_PROTOCOL.SetMemoryAttributes()
with only permission attributes set, let's simply ignore those for now.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The single user of EfiAttributeToArmAttribute () is the protocol
method EFI_CPU_ARCH_PROTOCOL.SetMemoryAttributes(), which uses the
return value to compare against the ARM attributes of an existing mapping,
to infer whether it is actually necessary to change anything, or whether
the requested update is redundant. This saves some cache and TLB
maintenance on 32-bit ARM systems that use uncached translation tables.
However, EFI_CPU_ARCH_PROTOCOL.SetMemoryAttributes() may be invoked with
only permission bits set, in which case the implied requested action is to
update the permissions of the region without modifying the cacheability
attributes. This is currently not possible, because
EfiAttributeToArmAttribute () ASSERT()s [on AArch64] on Attributes arguments
that lack a cacheability bit.
So let's simply return TT_ATTR_INDX_MASK (AArch64) or
TT_DESCRIPTOR_SECTION_TYPE_FAULT (ARM) in these cases (or'ed with the
appropriate permission bits). This way, the return value is equally
suitable for checking whether the attributes need to be modified, but
in a way that accommodates the use without a cacheability bit set.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Current Arm CpuDxe driver uses EFI_MEMORY_WP for write protection,
according to UEFI spec, we should use EFI_MEMORY_RO for write protection.
The EFI_MEMORY_WP is the cache attribute instead of memory attribute.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
PcdGenericWatchdogControlBase & PcdGenericWatchdogRefreshBase
are declared as UINT32 values in ArmPkg.dec, but for platforms
with addresses in the memory range above 4GB this causes build
error F000: Too large PCD value for datum type [UINT32]
of PCD gArmTokenSpaceGuid.PcdGenericWatchdogControlBase
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Alexei Fedorov <alexei.fedorov@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=361
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The generic timer support libraries call the actual system register
accessor function via a single pair of functions ArmArchTimerReadReg()
and ArmArchTimerWriteReg(), which take an enum argument to identify
the register, and return output values by pointer reference.
Since these functions are never called with a non-immediate argument,
we can simply replace each invocation with the underlying system register
accessor instead. This is mostly functionally equivalent, with the
exception of the bounds check for the enum (which is pointless given the
fact that we never pass a variable), the check for the presence of the
architected timer (which only makes sense for ARMv7, but is highly unlikely
to vary between platforms that are similar enough to run the same firmware
image), and a check for enum values that refer to the HYP view of the timer,
which we never referred to anywhere in the code in the first place.
So get rid of the middle man, and update the ArmGenericTimerPhyCounterLib
and ArmGenericTimerVirtCounterLib implementations to call the system
register accessors directly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
The DmaBufferAlignment currently defaults to 4, which is dangerously
small and may result in lost data on platforms that perform non-coherent
DMA. So instead, take the CWG value from the cache info registers.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Drop the include of AsmMacroIoLib.h, which contains GCC preprocessor macros
that RVCT does not use or require, given it has its own AsmMacroIoLib.inc
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
During Mmu initialization in the CpuDxe, for a page table any bits set
in the 'NextSectionAttributes' are garbage and were set from bits that
are actually part of the pagetable address. We clear it out to zero
so that the SyncCacheConfigPage will use the page attributes instead
of trying to convert the (bogus) section attributes into page
attributes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Kurt Kennett <kurt.kennett@microsoft.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The ArmGicLib API function GicGetCpuRedistributorBase () declares
GicCpuRedistributorBase to iterate over the redistributors of all
CPUs, but then inadvertently advances GicRedistributorBase instead.
Reported-by: "Oliyil Kunnil, Vishal" <vishalo@qti.qualcomm.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
According to the ACPI 6.0/6.1 spec, the physical base address of GICC,
GICD, GICR and GIC ITS is 64-bit. So change the type of the various GIC
base address PCDs to 64-bit, and fix up all users.
Contributed-under: TianoCore Contribution Agreement 1.0
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Dennis Chen <dennis.chen@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Annotate functions with ASM_FUNC() so that they are emitted into
separate sections.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Annotate functions with ASM_FUNC() so that they are emitted into
separate sections.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This commit fixes a bug in the GIC v2 and v3 drivers where the GICC_EOIR
(End Of Interrupt Register) is written twice for a single interrupt.
GicV(2|3)IrqInterruptHandler() calls the Interrupt Handler and then
GicV(2|3)EndOfInterrupt() on exit:
InterruptHandler = gRegisteredInterruptHandlers[GicInterrupt];
if (InterruptHandler != NULL) {
// Call the registered interrupt handler.
InterruptHandler (GicInterrupt, SystemContext);
} else {
DEBUG ((EFI_D_ERROR, "Spurious GIC interrupt: 0x%x\n", GicInterrupt));
}
GicV2EndOfInterrupt (&gHardwareInterruptV2Protocol, GicInterrupt);
although gInterrupt->EndOfInterrupt() can be expected to have already
been called by InterruptHandler() [which is the case for the primary
in-tree handler in TimerDxe]
The fix moves the EndOfInterrupt() call inside the else case for
unregistered/spurious interrupts. This removes a potential race
condition that might have lost interrupts.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Alexei Fedorov <alexei.fedorov@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Unlike SGIs and PPIs, which are private to the CPU and are managed at
the redistributor level (which is also a per-CPU construct), shared
interrupts (SPIs) are shared between all CPUs, and therefore managed at
the distributor level (just as on GICv2).
Reported-by: Narinder Dhillon <ndhillonv2@gmail.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Switch all users of ArmLib that depend on the MMU routines to the new,
separate ArmMmuLib. This needs to occur in one go, since the MMU
routines are removed from ArmLib build at the same time, to prevent
conflicting symbols.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
SErrors (formerly called asynchronous aborts) are a distinct class of
exceptions that are not closely tied to the currently executing
instruction. Since execution may be able to proceed in such a condition,
this class of exception is masked by default, and software needs to unmask
it explicitly if it is prepared to handle such exceptions.
On DEBUG builds, we are well equipped to report the CPU context to the user
and it makes sense to report an SError as soon as it occurs rather than to
wait for the OS to take it when it unmasks them, especially since the current
arm64/Linux implementation simply panics in that case. So unmask them when
ArmCpuDxe loads.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reassign all interrupts to non-secure Group-1 if the GIC has its DS
(Disable Security) bit set. In this case, it is safe to assume that we
own the GIC, and that no other firmware has performed any configuration
yet, which means it is up to us to reconfigure the interrupts so they
can be taken by the non-secure firmware.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The CpuIo2 protocol is required by the generic PciHostBridgeDxe driver,
which relies on it to back its own I/O and MMIO operations.
Since ARM has no native I/O port equivalent, such accesses can only
originate from PCI drivers, and the PCI I/O space is translated to MMIO
in this case.
So we can implement this protocol using MMIO operations only, and take
the PCI I/O translation offset into account when performing I/O port
accesses.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
mGicNumInterrupts is the total number of interrupts, so the interrupt
ID equal to mGicNumInterrupts is also invalid.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Use the new ARM/AArch64 implementation of the base
CpuExceptionHandlerLib library from CpuDxe to centralize
exception handling.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Update the CpuDxe driver to remove an assumption that it is the only
component modifying interrupt state since this can be done through BaseLib
as well. Instead of using a global variable for last interrupt state we
now check the current PSTATE value directly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Problems have been encountered because some of the source files have
execute permission set. This can cause git to report them as changed
when they are checked out onto a file system with inherited permissions.
This has been seen using Cygwin, MinGW and PowerShell Git.
This patch makes no change to source file content, and only aims to
correct the file modes/permissions.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19778 6f19259b-4bc3-4df7-8a09-765794883524
The CLANG assembler does not support the legacy, non-unified assembler syntax,
i.e., it does not support the reordering of the condition suffixes with the
increment/decrement before/after or byte/word suffixes, and it does not
recognize the 'empty descending' (ED) suffix at all. So move to the unified
syntax, and replace 'empty descending' with 'decrement after' or 'increment
before' as appropriate.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19280 6f19259b-4bc3-4df7-8a09-765794883524
In the function ArmGicEnableDistributor (), the Affinity Routing Enable
(ARE) bit, which essentially defines whether the GIC runs in v2 or v3
mode, is inadvertently cleared when enabling the GIC distributor if it
is running in v3 mode. So fix that.
Reported-by: Supreeth Venkatesh <Supreeth.Venkatesh@arm.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19274 6f19259b-4bc3-4df7-8a09-765794883524
Since we do not support anything below ARMv7, let's promote the ARMv6
exception handling code in CpuDxe to the only version we provide for
ARM. This means we can drop the unused ARMv4 version.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19273 6f19259b-4bc3-4df7-8a09-765794883524
This has the effect of splitting assembly functions into their own sections
so the linker can remove unused ones to save space.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@gmail.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19109 6f19259b-4bc3-4df7-8a09-765794883524
We currently rely on .align directives to ensure that each exception
vector entry is the appropriate offset from the vector base address.
This is slightly fragile, as were an entry to become too large (greater
than 32 A64 instructions), all following entries would be silently
shifted until they meet the next alignment boundary. Thus we might
execute the wrong code in response to an exception.
To prevent this, introduce a new macro, VECTOR_ENTRY, that uses .org
directives to position each entry at the precise required offset from
the base of a vector. A vector entry which is too large will trigger a
build failure rather than a runtime failure which is difficult to debug.
For consistency, the base and end of each vector is similarly annotated,
with VECTOR_BASE and VECTOR_END, which provide the necessary alignment
and symbol exports. The now redundant directives and labels are removed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18904 6f19259b-4bc3-4df7-8a09-765794883524
In ArmPkg/Include/Chipset, several CPU-specific header files reside.
Most of these provide no actual, or very little, use.
ARM1176JZ-S.h is not used at all (and unusable since SVN r18237).
ArmAemV8.h simply includes AArch64.h.
ArmCortexA15.h defines one processor-specific configuration bit and
then includes ArmV7.h.
Delete these include files, and update their sole users to function
without them.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18736 6f19259b-4bc3-4df7-8a09-765794883524
Interrupt must be disabled before we storing ELR and other system
registers, or else ELR will be overridden by interrupt reentrance.
This bug is critical as we may get occasional exception or dead loop
when interrupt reentrance occurs:
After increasing SP ... Before popping out registers
Or
After restoring ELR
The 1st circumstance could also be resolved by optimizing SP operation
(Pop out registers before adding SP back), but the 2nd could not be
resolved by disabling interrupt.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18538 6f19259b-4bc3-4df7-8a09-765794883524
No platforms use the ARMv6 (ARM11) support code anymore. In fact, the
only reference to it in ArmPkg.dsc was commented out by Andrew in SVN
r11298 (2011-02-03) so it may well be broken. So remove it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18237 6f19259b-4bc3-4df7-8a09-765794883524
Use an explicit VOID* cast when passing a static char array into
a function taking a void pointer.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18193 6f19259b-4bc3-4df7-8a09-765794883524
Ard Biesheuvel
Leif Lindholm
Evan Lloyd
Jiewen Yao
Alexei
Kurt Kennett
Dennis Chen
Giri P Mudusuru
Heyi Guo
Leendert van Doorn
Cohen, Eugene
Mark Rutland