RFC： https://bugzilla.tianocore.org/show_bug.cgi?id=3429
Intel's Trust Domain Extensions (Intel TDX) refers to an Intel technology
that extends Virtual Machines Extensions (VMX) and Multi-Key Total Memory
Encryption (MKTME) with a new kind of virutal machines guest called a
Trust Domain (TD). A TD is desinged to run in a CPU mode that protects the
confidentiality of TD memory contents and the TD's CPU state from other
software, including the hosting Virtual-Machine Monitor (VMM), unless
explicitly shared by the TD itself.
Note: Intel TDX is only available on X64, so the Tdx related changes are
in X64 path. In IA32 path, there may be null stub to make the build
success.
This patch includes below major changes.
1. Ia32/IntelTdx.asm
IntelTdx.asm includes below routines used in ResetVector
- IsTdx
Check if the running system is Tdx guest.
- InitTdxWorkarea
It initialize the TDX_WORK_AREA. Because it is called by both BSP and
APs and to avoid the race condition, only BSP can initialize the
WORK_AREA. AP will wait until the field of TDX_WORK_AREA_PGTBL_READY
is set.
- ReloadFlat32
After reset all CPUs in TDX are initialized to 32-bit protected mode.
But GDT register is not set. So this routine loads the GDT then jump
to Flat 32 protected mode again.
- InitTdx
This routine wrap above 3 routines together to do Tdx initialization
in ResetVector phase.
- IsTdxEnabled
It is a OneTimeCall to probe if TDX is enabled by checking the
CC_WORK_AREA.
- CheckTdxFeaturesBeforeBuildPagetables
This routine is called to check if it is Non-TDX guest, TDX-Bsp or
TDX-APs. Because in TDX guest all the initialization is done by BSP
(including the page tables). APs should not build the tables.
- TdxPostBuildPageTables
It is called after Page Tables are built by BSP.
byte[TDX_WORK_AREA_PGTBL_READY] is set by BSP to indicate APs can
leave spin and go.
2. Ia32/PageTables64.asm
As described above only the TDX BSP build the page tables. So
PageTables64.asm is updated to make sure only TDX BSP build the
PageTables. TDX APs will skip the page table building and set Cr3
directly.
3. Ia16/ResetVectorVtf0.asm
In Tdx all CPUs "reset" to run on 32-bit protected mode with flat
descriptor (paging disabled). But in Non-Td guest the initial state of
CPUs is 16-bit real mode. To resolve this conflict, BITS 16/32 is used
in the ResetVectorVtf0.asm. It checks the 32-bit protected mode or 16-bit
real mode, then jump to the corresponding entry point.
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
RFC： https://bugzilla.tianocore.org/show_bug.cgi?id=3429
Previously WORK_AREA_GUEST_TYPE was cleared in SetCr3ForPageTables64.
This is workable for Legacy guest and SEV guest. But it doesn't work
after Intel TDX is introduced. It is because all TDX CPUs (BSP and APs)
start to run from 0xfffffff0, thus WORK_AREA_GUEST_TYPE will be cleared
multi-times if it is TDX guest. So the clearance of WORK_AREA_GUEST_TYPE
is moved to Main16 entry point in Main.asm.
Note: WORK_AREA_GUEST_TYPE is only defined for ARCH_X64.
For Intel TDX, its corresponding entry point is Main32 (which will be
introduced in next commit in this patch-set). WORK_AREA_GUEST_TYPE will
be cleared there.
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3429
While build the initial page table, the SetCr3ForPageTables64 checks
whether SEV-ES is enabled. If so, clear the page encryption mask from the
GHCB page. Move the logic to clear the page encryption mask in the
AmdSev.asm.
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Min Xu <min.m.xu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Erdem Aktas <erdemaktas@google.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Min Xu <min.m.xu@intel.com>
Reviewed-by: Jiewen Yao <Jiewen.yao@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3429
Update the SEV support to switch to using the newer work area format.
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Min Xu <min.m.xu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Erdem Aktas <erdemaktas@google.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Min Xu <min.m.xu@intel.com>
Reviewed-by: Jiewen Yao <Jiewen.yao@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3275
The PageTables64.asm was created to provide routines to set the CR3
register for 64-bit paging. During the SEV support, it grew to include a
lot of the SEV stuff. Before adding more SEV features, let's move all
the SEV-specific routines into a separate file.
No functionality change intended.
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Min Xu <min.m.xu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Acked-by: Ard Biesheuvel <ardb+tianocore@kernel.org>
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3108
The early assembler code performs validation for some of the SEV-related
information, specifically the encryption bit position. To avoid having to
re-validate the encryption bit position as the system proceeds through its
boot phases, save the validated encryption bit position in the SEV-ES work
area for use by later phases.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@arm.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <2609724859cf21f0c6d45bc323e94465dca4e621.1610045305.git.thomas.lendacky@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3108
If a hypervisor incorrectly reports through CPUID that SEV-ES is not
active, ensure that a #VC exception was not taken. If it is found that
a #VC was taken, then the code enters a HLT loop.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@arm.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <afa2030b95b852313b13982df82d472187e59b92.1610045305.git.thomas.lendacky@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3108
To help mitigate against ROP attacks, add some checks to validate the
encryption bit position that is reported by the hypervisor.
The first check is to ensure that the hypervisor reports a bit position
above bit 31. After extracting the encryption bit position from the CPUID
information, the code checks that the value is above 31. If the value is
not above 31, then the bit position is not valid, so the code enters a
HLT loop.
The second check is specific to SEV-ES guests and is a two step process.
The first step will obtain random data using RDRAND and store that data to
memory before paging is enabled. When paging is not enabled, all writes to
memory are encrypted. The random data is maintained in registers, which
are protected. The second step is that, after enabling paging, the random
data in memory is compared to the register contents. If they don't match,
then the reported bit position is not valid, so the code enters a HLT
loop.
The third check is after switching to 64-bit long mode. Use the fact that
instruction fetches are automatically decrypted, while a memory fetch is
decrypted only if the encryption bit is set in the page table. By
comparing the bytes of an instruction fetch against a memory read of that
same instruction, the encryption bit position can be validated. If the
compare is not equal, then SEV/SEV-ES is active but the reported bit
position is not valid, so the code enters a HLT loop.
To keep the changes local to the OvmfPkg, an OvmfPkg version of the
Flat32ToFlat64.asm file has been created based on the UefiCpuPkg file
UefiCpuPkg/ResetVector/Vtf0/Ia32/Flat32ToFlat64.asm.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@arm.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <cb9c5ab23ab02096cd964ed64115046cc706ce67.1610045305.git.thomas.lendacky@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3108
Simplify and consolidate the SEV and SEV-ES checks into a single routine.
This new routine will use CPUID to check for the appropriate CPUID leaves
and the required values, as well as read the non-interceptable SEV status
MSR (0xc0010131) to check SEV and SEV-ES enablement.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@arm.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <43a660624c32b5f6c2610bf42ee39101c21aff68.1610045305.git.thomas.lendacky@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=2198
During BSP startup, the reset vector code will issue a CPUID instruction
while in 32-bit mode. When running as an SEV-ES guest, this will trigger
a #VC exception.
Add exception handling support to the early reset vector code to catch
these exceptions. Also, since the guest is in 32-bit mode at this point,
writes to the GHCB will be encrypted and thus not able to be read by the
hypervisor, so use the GHCB CPUID request/response protocol to obtain the
requested CPUID function values and provide these to the guest.
The exception handling support is active during the SEV check and uses the
OVMF temporary RAM space for a stack. After the SEV check is complete, the
exception handling support is removed and the stack pointer cleared.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@arm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=2198
A GHCB page is needed during the Sec phase, so this new page must be
created. Since the #VC exception handler routines assume that a per-CPU
variable area is immediately after the GHCB, this per-CPU variable area
must also be created. Since the GHCB must be marked as an un-encrypted,
or shared, page, an additional pagetable page is required to break down
the 2MB region where the GHCB page lives into 4K pagetable entries.
Create a new entry in the OVMF memory layout for the new page table
page and for the SEC GHCB and per-CPU variable pages. After breaking down
the 2MB page, update the GHCB page table entry to remove the encryption
mask.
The GHCB page will be used by the SEC #VC exception handler. The #VC
exception handler will fill in the necessary fields of the GHCB and exit
to the hypervisor using the VMGEXIT instruction. The hypervisor then
accesses the GHCB in order to perform the requested function.
Four new fixed PCDs are needed to support the SEC GHCB page:
- PcdOvmfSecGhcbBase UINT32 value that is the base address of the
GHCB used during the SEC phase.
- PcdOvmfSecGhcbSize UINT32 value that is the size, in bytes, of the
GHCB area used during the SEC phase.
- PcdOvmfSecGhcbPageTableBase UINT32 value that is address of a page
table page used to break down the 2MB page into
512 4K pages.
- PcdOvmfSecGhcbPageTableSize UINT32 value that is the size, in bytes,
of the page table page.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@arm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
SEV guest VMs have the concept of private and shared memory. Private
memory is encrypted with the guest-specific key, while shared memory
may be encrypted with hypervisor key. Certain types of memory (namely
instruction pages and guest page tables) are always treated as private
memory by the hardware. The C-bit in PTE indicate whether the page is
private or shared. The C-bit position for the PTE can be obtained from
CPUID Fn8000_001F[EBX].
When SEV is active, the BIOS is encrypted by the Qemu launch sequence,
we must set the C-bit when building the page table.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Tom Lendacky <Thomas.Lendacky@amd.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Currently, the value of the page tables' address is hard-coded in the
ResetVector. This patch replaces these values with a PCD dependency.
A check for the size has been added to alert the developer to rewrite
the ASM according to the new size, if it has been changed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Marvin Haeuser <Marvin.Haeuser@outlook.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
To help consolidate OVMF fixed memory uses, we declare this
range in MEMFD and thereby move it to 8MB.
We also now declare the table range in the FDF to set
PCDs. This allows us to ASSERT that CR3 is set as expected
in OVMF SEC.
OvmfPkgIa32.fdf and OvmfPkgIa32X64.fdf are updated simply
for consistency.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15146 6f19259b-4bc3-4df7-8a09-765794883524
In UEFI X64 we use other mechanisms to disable caching.
(CD/NW in CR0 and MTRRs.)
This fixes a slow boot issue with SVM.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14716 6f19259b-4bc3-4df7-8a09-765794883524
KVM has a bug that prevents using page tables in the ROM if the ROM
region utilizes the KVM READONLY memory feature. Therefore, we
avoid using page tables stored in the ROM.
Since OVMF doesn't require memory initialization, we just build
page table entries in RAM at 0x80000 very early in the OVMF boot
process. This address is just after the 'temp RAM' which is set
up by the SEC module.
Currently we only set up 4GB of page tables for OVMF's PEI,
but DxeIpl will build identity mapped page tables that cover all
of the available processor physical address space.
Reported-by: Gary Ching-Pang Lin <glin@suse.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14715 6f19259b-4bc3-4df7-8a09-765794883524
Min Xu
Brijesh Singh
Tom Lendacky
Michael D Kinney
Marvin Häuser
Jordan Justen
Laszlo Ersek