The bcdUSB value of usb3.1 is 0x0310, we update the condition judgment
to get correct max packet size for usb3.1 dev.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The GetKeyDescriptor() may return NULL when the KeyData is invalid.
For such case, we should go to error handling path rather than assert
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Fix UsbMouseAbsolutePointer driver GetState() interface to return
absolute value instead of relative value.
The driver is ported from UsbMouse driver. The GetState of
SimplePointer protocol returns relative value but the GetState
of AbsolutePointer protocol should return absolute value.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
EDKII usb stack is using a TPL_CALLBACK timer to monitor async transfer
request and signal event if it's done. As usb enumeration and usb mass
storage block i/o read/write runs on TPL_CALLBACK and TPL_NOTIFY level
respectively, It blocks usb async transfer requests, usually usb mouse
/use kb, getting time to run.
Without this change, user couldn't get usb mouse/kb state in time (will
show a little lag from UI view) when there is other usb transactions, such
as a new usb device inserted.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18169 6f19259b-4bc3-4df7-8a09-765794883524
1. Add delay after set device address and get configuration descriptor.
2. Sync the change at R15876 in XhciDxe to do not access transfer ring when endpoint is isochronous type or control type.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16105 6f19259b-4bc3-4df7-8a09-765794883524
1. Module UNI and Package UNI files are not DOS format. Convert them to DOS format.
2. Remove unused SectionExtractionDxeModStrs.uni and SectionExtractionPeiModStrs.uni
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Gao, Liming <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16044 6f19259b-4bc3-4df7-8a09-765794883524
2. Add MODULE_UNI_FILE file that contains the localized Abstract and Description of a module.
a. Addresses an information gap between INF files and the UEFI Distribution Packaging Specification XML schema
b. There will be an associated update to UPT in BaseTools to consume MODULE_UNI_FILE and associated UNI file during UDP creation that performs the INF -> XML conversion.
c. There will be an associated update to UPT in BaseTools to produce MODULE_UNI_FILE and associated UNI file during UDP installation that performs the XML -> INF conversion.
3. Add Module Extra UNI file that provides the localized Name of a module.
a. [UserExtensions.TianoCore."ExtraFiles"] provides an easy method for a module to specify extra files not listed in [Sources] or [Binaries] sections to be added to a UDP without having to list the files in the UPT package information data file.
b. There will be an associated update to UPT in BaseTools to package up files listed in [UserExtensions.TianoCore."ExtraFiles"] during UDP creation.
c. UNI file contains localized name of a module to go along with the localized Abstract and Description from the MODULE_UNI_FILE.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zeng, Star <star.zeng@intel.com>
Reviewed-by: Gao, Liming <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15963 6f19259b-4bc3-4df7-8a09-765794883524
1. Usage information in INF file comment blocks are either incomplete or incorrect.
This includes usage information for Protocols/PPIs/GUIDs/PCDs/HOBs/Events/BootModes.
The syntax for usage information in comment blocks is defined in the EDK II Module Information (INF) Specification
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zeng, Star <star.zeng@intel.com>
Reviewed-by: Gao, Liming <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15962 6f19259b-4bc3-4df7-8a09-765794883524
If the structure layout in UsbBusPei is changed, then the UsbBotPei will not work.
1. As the maximum number of endpoints is 16, use UINT16 type rather than UINT8 for DataToggle.
2. DataToggle needs to be reset to 0 when endpoint stall is cleared, do it in PeiUsbControlTransfer().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15185 6f19259b-4bc3-4df7-8a09-765794883524
1.Port reset process may not be proper for some vendor's SS hubs. If the corresponding port shows the reset has been done by C_RESET bit we have to skip the whole reset process for attached devices.
2.Clean C_BH_RESET bit immediately to avoid usb timer entering too many times when 5 tiers hubs are connected.
3.Stop checking URB if there is an error happened.
4.Better error handling for fast hot-plug.
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Elvin Li <elvin.li@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@14889 6f19259b-4bc3-4df7-8a09-765794883524
The r14226 check-in indeed has memory leak in allocated "Child" pointer. UsbBusDriverBindingStop() may dereference this pointer and may bring exception on invalid memory access
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@14251 6f19259b-4bc3-4df7-8a09-765794883524
1.enlarge the recovery time from 10ms to 20ms after port reset to make set address request success for better device compatibility.
2.another enhancement is to use RESET_C bit rather than RESET bit to judge if hub reset port operation is done.
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Elvin Li <elvin.li@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@14227 6f19259b-4bc3-4df7-8a09-765794883524
1.Fix the bug in interface parser logic for usb camera device. Reserve device address if the device doesn’t get disconnected.
2.Some usb 1.1 devices require the context evaluation immediately with actual max packet size after detecting the device max packet size.
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Elvin Li <elvin.li@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@14226 6f19259b-4bc3-4df7-8a09-765794883524
Clean up the code to remove unnecessary NotifyHandle in the private data structure.
Signed-off-by: Ruiyu Ni<ruiyu.ni@intel.com>
Reviewed-by: Elvin Li<elvin.li@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13565 6f19259b-4bc3-4df7-8a09-765794883524
Enhance ConSplitter to register hot keys for new connected consoles.
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hot Tian <hot.tian@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13358 6f19259b-4bc3-4df7-8a09-765794883524
1) Fix a bug on missing hub context evaluation operation.
2) If the usb keyboard device configuration has been set successfully, then don’t set configuration again.
Signed-off-by: erictian
Reviewed-by: li-elvin
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13087 6f19259b-4bc3-4df7-8a09-765794883524
1) XHCI host controller hw always provides more than 5 interrupters.
Now using interrupter 0 to accommodate all received events.
2) XHCI host controller hw always provides 32bytes context size.
Now it dynamically detect context size and construct it.
also solved several issues:
1) Divides 64byte width register access to two 32bit registers access because some XHCI chipsets cannot support a single 64bit access.
2) Remove halt host controller statement in UsbBusDriverBindingStop(). It has been done by host controller’s DriverBindingStop(). And XhciDriverBindingStop() need XHCI host controller is in running state because it need execute DISABLE_SLOT cmd to release h/w resource.
signed-off-by: erictian
Reviewed-by: li-elvin
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12785 6f19259b-4bc3-4df7-8a09-765794883524
GCC 4.6 generates a warning when a variable is set,
but never used.
Signed-off-by: jljusten
Reviewed-by: lgao4
Reviewed-by: erictian
Reviewed-by: rsun3
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12617 6f19259b-4bc3-4df7-8a09-765794883524
Feng Tian
Alcantara, Paulo
Ruiyu Ni
Jordan Justen
Laszlo Ersek
jaben carsey
Star Zeng
Nikolai Saoukh
Gao, Liming
Samer El-Haj-Mahmoud
erictian
niruiyu
ydong10
li-elvin
jljusten