PCD PcdNullPointerDetectionPropertyMask is a bitmask used to control the
NULL address detection functionality in code for different phases.
If enabled, accessing NULL address in UEFI or SMM code can be caught
as a page fault exception.
BIT0 - Enable NULL pointer detection for UEFI.
BIT1 - Enable NULL pointer detection for SMM.
BIT2..6 - Reserved for future uses.
BIT7 - Disable NULL pointer detection just after EndOfDxe. This is a
workaround for those unsolvable NULL access issues in
OptionROM, boot loader, etc. It can also help to avoid
unnecessary exception caused by legacy memory (0-4095) access
after EndOfDxe, such as Windows 7 boot on Qemu.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Ayellet Wolman <ayellet.wolman@intel.com>
Suggested-by: Ayellet Wolman <ayellet.wolman@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
FV3 HOB was introduced by new (>= 1.5) PI spec, it is intended to
be used to propagate PEI-phase FV authentication status to DXE.
This patch is to update PeiCore to build FV3 HOB with the
authentication status and DxeCore to get the authentication
status from FV3 HOB when producing FVB Protocol.
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
According to the TCG Platform Reset Attack Mitigation Specification (May
15, 2008):
> 5 Interface for UEFI
> 5.1 UEFI Variable
> 5.1.1 The MemoryOverwriteRequestControl
>
> Start of informative comment:
>
> [...] The OS loader should not create the variable. Rather, the firmware
> is required to create it and must support the semantics described here.
>
> End of informative comment.
However, some OS kernels create the MOR variable even if the platform
firmware does not support it (see one Bugzilla reference below). This OS
issue breaks the logic added in the last patch.
Strengthen the MOR check by searching for the TCG or TCG2 protocols, as
edk2's implementation of MOR depends on (one of) those protocols.
The protocols are defined under MdePkg, thus there's no inter-package
dependency issue. In addition, calling UEFI services in
MorLockInitAtEndOfDxe() is safe, due to the following order of events /
actions:
- platform BDS signals the EndOfDxe event group,
- the SMM core installs the SmmEndOfDxe protocol,
- MorLockInitAtEndOfDxe() is invoked, and it calls UEFI services,
- some time later, platform BDS installs the DxeSmmReadyToLock protocol,
- SMM / SMRAM is locked down and UEFI services become unavailable to SMM
drivers.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Ladi Prosek <lprosek@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1498159
Suggested-by: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Ladi Prosek <lprosek@redhat.com>
The "MemoryOverwriteRequestControl" (a.k.a. MOR) variable comes from the
"TCG Platform Reset Attack Mitigation Specification":
https://www.trustedcomputinggroup.org/wp-content/uploads/Platform-Reset-Attack-Mitigation-Specification.pdf
The "MemoryOverwriteRequestControlLock" variable (a.k.a. MORL) is a
Microsoft extension, called "Secure MOR implementation":
https://docs.microsoft.com/en-us/windows-hardware/drivers/bringup/device-guard-requirements
Currently the VariableSmm driver creates MORL without regard to MOR. This
can lead to a situation where a platform does not support MOR from the
prerequisite spec (because it does not include the
"SecurityPkg/Tcg/MemoryOverwriteControl/TcgMor.inf" driver), but appears
to support MORL from the dependent Microsoft spec.
"winload.efi" notices this inconsistency, and disables the Device Guard
Virtualization Based Security in Windows Server 2016 and Windows 10 64-bit
Enterprise.
If the platform includes
"SecurityPkg/Tcg/MemoryOverwriteControl/TcgMor.inf", then MOR will exist
by the time EndOfDxe is reached, and VariableSmm can safely create MORL.
Otherwise, do not create MORL (delete it if it exists), and also prevent
other modules from creating it.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Ladi Prosek <lprosek@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=727
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1496170
Reported-by: Ladi Prosek <lprosek@redhat.com>
Suggested-by: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Ladi Prosek <lprosek@redhat.com>
The SetMorLockVariable() function sets "mMorLockPassThru" to TRUE
temporarily, so that it can set the MOR Control Lock variable to
well-formed values without permission checks.
In the next patch, we'll need the same override for deleting the MOR
Control Lock variable; hence obey "mMorLockPassThru" in the deletion
branch of SetVariableCheckHandlerMorLock() as well.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Ladi Prosek <lprosek@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Ladi Prosek <lprosek@redhat.com>
Introduce the MorLockInitAtEndOfDxe() hook, in order to allow
MorLockInit() to delay / queue operations until EndOfDxe. (Or, if the
platform never signals EndOfDxe, until ReadyToBoot.)
Call MorLockInitAtEndOfDxe() whenever we set "mEndOfDxe" to TRUE:
- in VariableRuntimeDxe:
- in the OnReadyToBoot() function,
- in the OnEndOfDxe() function;
- in VariableSmm:
- on the SMM_VARIABLE_FUNCTION_READY_TO_BOOT SMI request,
- in the SmmEndOfDxeCallback() function.
For now, implement MorLockInitAtEndOfDxe() as a no-op in both
VariableRuntimeDxe and VariableSmm.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Ladi Prosek <lprosek@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Ladi Prosek <lprosek@redhat.com>
The MorLockInit() and SetVariableCheckHandlerMor() functions have separate
implementations for VariableRuntimeDxe (= unprivileged, unified
DXE_RUNTIME driver) and VariableSmm (= privileged, DXE_SMM back-end of the
split variable driver).
Move their declarations from "Variable.c" to "PrivilegePolymorphic.h", so
that the compiler enforce that the declarations and the definitions match.
(All C source files with the call sites and the function definitions
already include "PrivilegePolymorphic.h" via "Variable.h".)
At the same time:
- replace two typos in the MorLockInit() description:
- replace "EFI_SUCEESS" with "EFI_SUCCESS",
- replace "MOR Lock Control" with "MOR Control Lock";
- in the SetVariableCheckHandlerMor() description:
- replace @param with @param[in],
- correct the description of the Attributes parameter (suggested by Star
Zeng <star.zeng@intel.com>),
- rewrap the comment to 80 columns.
This change cleans up commit 2f6aa774fe ("MdeModulePkg: Add MorLock to
variable driver.", 2016-01-19).
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Ladi Prosek <lprosek@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Ladi Prosek <lprosek@redhat.com>
If the platform supports SMM, a gRT->SetVariable() call at boot time
results in the following call tree to SecureBootHook():
RuntimeServiceSetVariable() [VariableSmmRuntimeDxe.c, unprivileged]
SmmVariableHandler() [VariableSmm.c, PRIVILEGED]
VariableServiceSetVariable() [Variable.c, PRIVILEGED]
SecureBootHook() [VariableSmm.c, PRIVILEGED]
//
// do nothing
//
SecureBootHook() [Measurement.c, unprivileged]
//
// measure variable if it
// is related to SB policy
//
And if the platform does not support SMM:
VariableServiceSetVariable() [Variable.c, unprivileged]
SecureBootHook() [Measurement.c, unprivileged]
//
// measure variable if it
// is related to SB policy
//
In other words, the measurement always happens outside of SMM.
Because there are two implementations of the SecureBootHook() API, one
that is called from SMM and does nothing, and another that is called
outside of SMM and measures variables, the function declaration should be
in a header file. This way the compiler can enforce that the function
declaration and all function definitions match.
"Variable.h" is used for "including common header files, defining internal
structures and functions used by Variable modules". Technically, we could
declare SecureBootHook() in "Variable.h". However, "Measurement.c" and
"VariableSmmRuntimeDxe.c" themselves do not include "Variable.h", and that
is likely intentional -- "Variable.h" exposes so much of the privileged
variable implementation that it is likely excluded from these C source
files on purpose.
Therefore introduce a new header file called "PrivilegePolymorphic.h".
"Variable.h" includes this header (so that all C source files that have
been allowed to see the variable internals learn about the new
SecureBootHook() declaration immediately). In "Measurement.c" and
"VariableSmmRuntimeDxe.c", include *only* the new header.
This change cleans up commit fa0737a839 ("MdeModulePkg Variable: Merge
from Auth Variable driver in SecurityPkg", 2015-07-01).
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Ladi Prosek <lprosek@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Ladi Prosek <lprosek@redhat.com>
EFI_BOOT_SCRIPT_WRITE() interface is a var-arg interface.
Spec defines the order of parameters for
EFI_BOOT_SCRIPT_PCI_CONFIG2_WRITE_OPCODE as below:
typedef
EFI_STATUS
(EFIAPI *EFI_BOOT_SCRIPT_WRITE) (
IN CONST EFI_S3_SAVE_STATE_PROTOCOL *This,
IN UINT16 OpCode,
IN EFI_BOOT_SCRIPT_WIDTH Width,
IN UINT16 Segment,
IN UINT64 Address,
IN UINTN Count,
IN VOID *Buffer
);
But implementation assumes Segment is in the very end, after Buffer.
Similar spec/implementation gaps are also found for
EFI_BOOT_SCRIPT_PCI_CONFIG2_READ_WRITE_OPCODE.
The patch fixes the implementation to extract the arguments in
correct order.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Commit 8932679df5 adds an ASSERT for
checking NULL pointer dereference.
The ASSERT added here is for addressing a false positive NULL pointer
dereference issue raised from static analysis.
This commit adds comments to clarify the reason for using ASSERT as the
check.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=720
The current implementation assumes there is only one hotplug resource
padding for each resource type. It's not true considering
DegradeResource(): MEM64 resource could be degraded to MEM32
resource.
The patch treat the resource paddings using the same logic as
treating typical/actual resources and the total resource of a bridge
is set to the MAX of typical/actual resources and resource paddings.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The debug messages can help developer to know the pre-memory
allocation usage.
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=699
Within function AhciModeInitialization(), left shift operations of 'BIT0'
in the following statements:
"if ((PortImplementBitMap & (BIT0 << Port)) != 0) {"
will incur possible out of range left shift when Port is 31, since
"1 << 31" is possible to exceed the range of type 'int' (signed).
According to the C11 spec, Section 6.5.7:
> 4 The result of E1 << E2 is E1 left-shifted E2 bit positions; vacated
> bits are filled with zeros. If E1 has an unsigned type, the value
> of the result is E1 * 2^E2 , reduced modulo one more than the
> maximum value representable in the result type. If E1 has a signed
> type and nonnegative value, and E1 * 2^E2 is representable in the
> result type, then that is the resulting value; otherwise, the
> behavior is undefined.
This commit explicitly cast 'BIT0' with UINT32 to resolve this issue.
Cc: Steven Shi <steven.shi@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=698
Within function NetRandomInitSeed(), left shift a negative value is used
in:
"~Time.Hour << 24"
which involves undefined behavior.
Since Time.Hour is of type UINT8 (range from 0 to 23), hence ~Time.Hour
will be a negative value (of type int, signed).
According to the C11 spec, Section 6.5.7:
> 4 The result of E1 << E2 is E1 left-shifted E2 bit positions; vacated
> bits are filled with zeros. If E1 has an unsigned type, the value
> of the result is E1 * 2^E2 , reduced modulo one more than the
> maximum value representable in the result type. If E1 has a signed
> type and nonnegative value, and E1 * 2^E2 is representable in the
> result type, then that is the resulting value; otherwise, the
> behavior is undefined.
This commit will remove the '~' operator before 'Time.Hour', since it
seems like an implementation choice for generating the seed.
Cc: Steven Shi <steven.shi@intel.com>
Cc: Qin Long <qin.long@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=695
Within function CoreRestoreTpl(), left shift a negative value -2 is used
in:
"while (((-2 << NewTpl) & gEventPending) != 0) {"
which involves undefined behavior.
According to the C11 spec, Section 6.5.7:
> 4 The result of E1 << E2 is E1 left-shifted E2 bit positions; vacated
> bits are filled with zeros. If E1 has an unsigned type, the value
> of the result is E1 * 2^E2 , reduced modulo one more than the
> maximum value representable in the result type. If E1 has a signed
> type and nonnegative value, and E1 * 2^E2 is representable in the
> result type, then that is the resulting value; otherwise, the
> behavior is undefined.
This commit refines the code logic to avoid left shifting the negative
value.
Cc: Steven Shi <steven.shi@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=702
Within function InternalPrintLibSPrintMarker(), possible left shift of a
negative value is found in:
"(*(ArgumentString + 1) << 8)"
which involves undefined behavior.
Since '*(ArgumentString + 1)' is of type CONST CHAR8 (signed), it will be
promoted to type int (signed) during the left shift operation. If
'*(ArgumentString + 1)' is a negative value, the behavior will be
undefined.
According to the C11 spec, Section 6.5.7:
> 4 The result of E1 << E2 is E1 left-shifted E2 bit positions; vacated
> bits are filled with zeros. If E1 has an unsigned type, the value
> of the result is E1 * 2^E2 , reduced modulo one more than the
> maximum value representable in the result type. If E1 has a signed
> type and nonnegative value, and E1 * 2^E2 is representable in the
> result type, then that is the resulting value; otherwise, the
> behavior is undefined.
This commit explicitly cast '*(ArgumentString + 1)' with UINT8 to resolve
this issue.
Cc: Steven Shi <steven.shi@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Current implementation deletes the "BootNext" before calling
any PlatformBootManagerLib APIs, but if system resets in
PlatformBootManagerLib APIs, "BootNext" is not consumed but lost.
The patch defers the deletion of "BootNext" to before booting it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
In NetbufTrim() function, the NetBuf TotalSize should be checked with 0 before
making the trim operation, otherwise the function will fall into infinite loop.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
The patch dynamically enables Bus Master on P2P bridges only
when requested by a device driver through PciIo.Attribute() to enable
the Bus Master.
Signed-off-by: Sean Brogan <sean.brogan@microsoft.com>
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Within function GetAllocationDescriptorLsn():
The call to GetPdFromLongAd() may return NULL and it will be later
dereferenced in GetShortAdLsn().
This commit adds ASSERT to resolve the potential NULL pointer
dereference.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Paulo Alcantara <pcacjr@zytor.com>
Follow PI 1.6 spec to support FFS_ATTRIB_DATA_ALIGNMENT_2 for
FFS alignment extended to support maximum 16MB.
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Do not reserve entire block device size for an UDF file system -
instead, reserve the appropriate space (UDF logical volume space) for
it.
Additionally, only create a logical partition for UDF logical volumes
that are currently supported by EDK2 UDF file system implementation. For
instance, an UDF volume with a single LVD and a single Physical (Type 1)
Partition will be supported.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Reported-by: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Paulo Alcantara <pcacjr@zytor.com>
Tested-by: Hao Wu <hao.a.wu@intel.com>
Build-tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Build-tested-by: Star Zeng <star.zeng@intel.com>
Build-tested-by: Paulo Alcantara <paulo@hp.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Add NULL pointer check before using a pointer to avoid possible
NULL pointer dereference.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Change since v4: Revise the patch based on V4 sent by Amit Kumar
1) Only return the corresponding protocol interface in *Interface
if the return status is EFI_SUCCESS or EFI_ALREADY_STARTED.
2) Interface is returned unmodified for all error conditions except
EFI_UNSUPPORTED and EFI_ALREADY_STARTED, NULL will be returned in
*Interface when EFI_UNSUPPORTED and Attributes is not
EFI_OPEN_PROTOCOL_TEST_PROTOCOL, the protocol interface will be
returned in *Interface when EFI_ALREADY_STARTED.
Change since v3:
1) Fixed issue when Attributes = EFI_OPEN_PROTOCOL_TEST_PROTOCOL
and Inteface = NULL case. [Reported by:star.zeng at intel.com]
Change Since v2:
1) Modified to use EFI_ERROR to get status code
Change since v1:
1) Fixed typo protocal to protocol
2) Fixed coding style
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Amit Kumar <amit.ak@samsung.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Gabriel Somlo <gsomlo@gmail.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Amit Kumar <amit.ak@samsung.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Gabriel Somlo <gsomlo@gmail.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=545
For oneof/numeric/CheckBox(storage can be Bit VarStore)
If the question value can be updated and shown correctly
in UI page, we need do enhancements in following cases:
1. Parse the Ifr data to get the bit VarStore info correctly.
2. Set/get value to/from bit VarStore correctly.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=545
For oneof/numeric/checkbox, their storage may be bit field.
When generating <ConfigAltResp> string to get default value
for these questions, we need to parse the Ifr data to get
the bit Varstore info,and then generating the correct
<ConfigAltResp> string.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=545
In UefiHiiLib, there are codes to validate the current setting of
questions, now update the logic to handle question with bit storage.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
From GCD perspective, its SetMemorySpaceAttributes() method doesn't accept page
related attributes. That means users cannot use it to change page attributes,
and have to turn to CPU arch protocol to do it, which is not be allowed by PI
spec.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Suggested-by: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Similar to the naming style for variables, it's better for the name of
members in a enum type to avoid using only upper-case letters.
Cc: Paulo Alcantara <pcacjr@zytor.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Paulo Alcantara <pcacjr@zytor.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The local GUID variable 'UdfDevPathGuid', it has been initialized during
its declaration.
For better coding style, this commit uses a global variable instead.
Cc: Paulo Alcantara <pcacjr@zytor.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Paulo Alcantara <pcacjr@zytor.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
In ResolveSymlink(), replace the following variable:
CHAR16 *C;
with:
CHAR16 *Char;
Cc: Paulo Alcantara <pcacjr@zytor.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Paulo Alcantara <pcacjr@zytor.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Case 1 - Within DuplicateFid() & DuplicateFe():
The call to AllocateCopyPool() may return NULL.
Add ASSERTs as checks.
Case 2 - Within UdfRead():
Add ASSERT to ensure 'NewFileEntryData' returned from FindFileEntry()
will not be NULL pointer.
Case 3 - Within GetAllocationDescriptorLsn():
The return value of 'GetPdFromLongAd (Volume, ParentIcb)' may be NULL,
and it will be passed into function GetShortAdLsn() which will
dereference it.
Add ASSERT in GetShortAdLsn() as check.
Case 4 - Within ReadFile():
Add ASSERT to ensure 'Data' returned from GetAedAdsData() will not be NULL
pointer.
Case 5 - Within InternalFindFile():
If both 'Parent->FileIdentifierDesc' and 'Icb' are NULL, then possible
NULL pointer dereference will happen in ReadDirectoryEntry().
Add additional check to resolve.
Cc: Paulo Alcantara <pcacjr@zytor.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Paulo Alcantara <pcacjr@zytor.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Issue : When try to change serial attributes using sermode
command, the default values are set with the execute flow
as below.
The sermode command calls SerialSetAttributes, which sets H/W
attributes of Serial device. After that the SerialIo protocol is
reinstalled, which causes MdeModulePkg/Universal/Console/TerminalDxe
and MdeModulePkg/Universal/Console/ConPlatformDxe drivers' bindings
to stop and then start. This in turn calls SerialReset, which undoes
changes of SerialSetAttributes.
Cause : The SerialReset command resets the attributes' values
to default.
Fix : Serial Reset command should set the attributes which have
been changed by user after calling SerialSetAttributes.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The generic driver has no way to know whether an OEM type should
be filtered or not.
This patch is to update the code to skip measurement for OEM type
and platform code can measure it by self if required.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Chasel Chiu <chasel.chiu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Chasel Chiu <chasel.chiu@intel.com>
Update XHCI driver to consume IOMMU_PPI to allocate DMA buffer.
If no IOMMU_PPI exists, this driver still calls PEI service
to allocate DMA buffer, with assumption that DRAM==DMA.
This is a compatible change.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This IOMMU_PPI is to provide IOMMU abstraction in PEI.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=704
For root directory, the FID (File Identifier Descriptor) pointer is
accessible through PRIVATE_UDF_FILE_DATA.Root, whereas non-root
directory and regular files, their FIDs are accessible through
PRIVATE_UDF_FILE_DATA.File.
In UdfSetPosition(), the FID was retrieved through
PRIVATE_UDF_FILE_DATA.File, hence when calling it with a root directory,
PRIVATE_UDF_FILE_DATA.File.FileIdentifierDescriptor would be NULL and
then dereferenced.
This patch fixes the NULL pointer dereference by calling _FILE() to
transparently return the correct UDF_FILE_INFO * which points to a valid
FID descriptor of a specific file.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Steven Shi <steven.shi@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Reported-by: Steven Shi <steven.shi@intel.com>
Signed-off-by: Paulo Alcantara <pcacjr@zytor.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
VS2010/VS2012 build failure with below info:
warning C4701:
potentially uninitialized local variable 'DataOffset' used
potentially uninitialized local variable 'FilePosition' used
potentially uninitialized local variable 'FinishedSeeking' used
potentially uninitialized local variable 'Data' used
warning C4703:
potentially uninitialized local pointer variable 'Data' used
In fact, DataOffset, FilePosition and FinishedSeeking are initialized
and then used if (ReadFileInfo->Flags == READ_FILE_SEEK_AND_READ).
DoFreeAed will be set to TRUE when Data is allocated and returned from
GetAedAdsData(), and Data will be freed if (DoFreeAed) when exiting.
Use same method at 5afa5b8159 to fix
the build failure.
There is related discussion at
https://lists.01.org/pipermail/edk2-devel/2017-September/014641.html
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Paulo Alcantara <pcacjr@zytor.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Paulo Alcantara <pcacjr@zytor.com>
When building the driver for DEBUG/RELEASE, GCC48/GCC49 warn about
ReadFile() possibly using "BytesLeft" without initializing it first.
This is not the case. The reads of "BytesLeft" are only reachable if
(ReadFileInfo->Flags == READ_FILE_SEEK_AND_READ). But, in that case, we
also set "BytesLeft" to "ReadFileInfo->FileDataSize", near the top of the
function.
Assign "BytesLeft" zero at the top, and add a comment that conforms to the
pending Coding Style Spec feature request at
<https://bugzilla.tianocore.org/show_bug.cgi?id=607>.
This issue was reported by Ard's and Gerd's CI systems independently.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Paulo Alcantara <pcacjr@zytor.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: Gerd Hoffmann <kraxel@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Paulo Alcantara <pcacjr@zytor.com>
The ECMA-167 standard (3rd Edition, June 1997) reserves values 4 through 7
in the ICB.Flags[2:0] bit-field for future standardization; see "14.6 ICB
Tag" / "14.6.8 Flags (RBP 18)".
https://www.ecma-international.org/publications/standards/Ecma-167.htm
The
switch (RecordingFlags)
statement in the ReadFile() function handles all the standard values,
using the constants of the UDF_FE_RECORDING_FLAGS enum type. However, the
reserved values are not caught with a "default" case label, which both
breaks the edk2 Coding Style Spec, and leaves the Status variable
un-initialized, before we return Status under the Done label.
Set Status to EFI_UNSUPPORTED if we encounter a reserved value.
This issue was reported by Ard's and Gerd's CI systems independently
(through build failures with GCC48/GCC49, DEBUG/RELEASE targets).
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Paulo Alcantara <pcacjr@zytor.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: Gerd Hoffmann <kraxel@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Paulo Alcantara <pcacjr@zytor.com>
Wang, Jian J
Dandan Bi
Star Zeng
Liming Gao
Laszlo Ersek
Ruiyu Ni
Hao Wu
Fu Siyuan
Paulo Alcantara
Amit Kumar
Pankaj Bansal
Jiewen Yao