In Ip4CleanService()it first cleaned some resources, then stop the timer .
While before the timer stopped it may try to access some already freed
data, which may generate an exception.
This patch updates the driver to stop the timer event before starting to
clean up the service data.
Cc: Wu Jiaxin <jiaxin.wu@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Subramanian Sriram <sriram-s@hpe.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
Reviewed-by: Sriram Subramanian <sriram-s@hpe.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
Potentially uninitialized local variables 'TableKey' and 'TableHeader'
might be used in functions RamDiskPublishNfit() and RamDiskUnpublishNfit()
in file RamDiskProtocol.c.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Qiu Shumin <shumin.qiu@intel.com>
According to PI specification, EndOfDxe Event should be signaled before
DxeSmmReadyToLock protocol installation. This update is ASSERT if EndOfDxe
Event is not signaled when DxeSmmReadyToLock protocol installed. And do
REPORT_STATUS_CODE() also.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
PI1.4a spec added "For S3 resume boot modes DXE IPL must be
prepared to execute without permanent memory installed and
invoke the S3 resume modules."
To follow PI1.4a spec, this patch is to update DxeIpl and
PeiCore to enable S3 resume from temporary memory.
The normal boot path still enforces the permanent memory
requirement.
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Tested-by: Katie Dellaquila <katie.dellaquila@hp.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
The current PCI 64bit memory BAR size calculation in PciHostBridgeLib
assumes all 32 bits in the upper BAR are fully writable. However,
platform might only support partial address programming, such as 40bit
PCI BAR address. In this case the complement cannot be used for size
calculation. Instead, the lowest non-zero bit should be used for BAR
size calculation.
Cc: Prince Agyeman <prince.agyeman@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Maurice Ma <maurice.ma@intel.com>
Reviewed-by: Prince Agyeman <prince.agyeman@intel.com>
CorebootPayloadPkg has switched to use the generic PciBus and
PciHostBridge driver form MdeModulePkg. As a result, the
non-enumeration drivers including PciBusNoEnumerationDxe and
PciRootBridgenoEnumerationDxe need to be removed.
Cc: Prince Agyeman <prince.agyeman@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Maurice Ma <maurice.ma@intel.com>
Reviewed-by: Prince Agyeman <prince.agyeman@intel.com>
The current GenCfgOpt tool does not generate bit fields in BSF.
This change will allow bit fields to be created in BSF for a specific
FSP UPD item. The argument for the tool is also updated to be in sync
with the old usage model in IntelFspPkg.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Maurice Ma <maurice.ma@intel.com>
Reviewed-by: Jiewen Yao <Jiewen.yao@intel.com>
Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
OVMF (unlike ArmVirtPkg) has traditionally cleared the screen after
connecting devices. This is not really necessary, and keeping the logo up
while the progress bar is advancing at the bottom looks great. So don't
clear the screen.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
OVMF's Platform BDS used to have a nice progress bar (with
IntelFrameworkModulePkg BDS). We can restore it by copying the
PlatformBootManagerWaitCallback() function verbatim from
Nt32Pkg/Library/PlatformBootManagerLib/PlatformBootManager.c
It can be tested by passing the following option to QEMU (5 seconds):
-boot menu=on,splash-time=5000
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
In the course of porting OvmfPkg to the MdeModulePkg BDS, commit
817fb3ac2a
OvmfPkg/PlatformBootManagerLib: Add EnableQuietBoot & DisableQuietBoot
open-coded the EnableQuietBoot() function (and its dependencies / friends)
from IntelFrameworkModulePkg BDS.
This code duplication can be avoided; the functionality is available from
the following three libraries in MdeModulePkg:
- BootLogoLib: provides the BootLogoEnableLogo() function. It does not
provide the internal ConvertBmpToGopBlt() function -- that one is
delegated to ImageDecoderLib (function DecodeImage()).
- ImageDecoderLib: a general library that registers decoder plugins for
specific image formats, and provides the generic DecodeImage() on top.
- BmpImageDecoderLib: one of said decoder plugins, for handling BMP images
(which is the format of our logo).
In this patch, we revert 817fb3ac2a, and atomically incorporate the
above libraries. This is inspired by Nt32Pkg commit 859e75c4fc42:
Nt32Pkg: Use BootLogoLib for logo and progress bar drawing.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
The BootLogoUpdateProgress() function uses the
EFI_GRAPHICS_OUTPUT_BLT_PIXEL type in its parameter list, but the protocol
header that defines this type is not included. This breaks dependent C
source files that don't otherwise include the GraphicsOutput protocol
header. Supply the necessary include directive.
(Similarly, BootLogoEnableLogo() uses
EDKII_PLATFORM_LOGO_DISPLAY_ATTRIBUTE in its parameter list. For that
however, the PlatformLogo protocol header is included already.)
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
The PlatformBootManagerWaitCallback() function sets White.Reserved to
0xFF; it should be 0x00. Also, use a more compact form to assign the
component fields.
Suggested-by: Jordan Justen <jordan.l.justen@intel.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Move NvmExpressHci.h definitions to a public industry standard
header in MdePkg. The NvmExpressHci.h contains definitions based
on the NVMe v1.1 specification. These definitions should be in
a public header so that clients of the NVMe passthru protocol
can use them to execute NVMe commands.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Darbin Reyes <darbin.emm.reyes@hpe.com>
Reviewed-by: Samer El-Haj-Mahmoud <samer.el-haj-mahmoud@hpe.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Adds a public header for NVMe v1.1 spec. definitions. The majority
of these definitions where copied from a private header in
MdeModulePkg/Bus/Pci/NvmExpress/NvmExpressHci.h. Additional
definitions were added e.g. the NVMe Smart Health Log and
Firmware Info. Log structures. These definitions should be
in a public header so that clients of the NVMe passthru protocol
can use them to execute NVMe commands.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Darbin Reyes <darbin.emm.reyes@hpe.com>
Reviewed-by: Samer El-Haj-Mahmoud <samer.el-haj-mahmoud@hpe.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
this is something I missed in 8ac46e4
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Zimmermann <sigmaepsilon92@gmail.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
When OVMF tried to restore the variables from the file-based NvVars, it
failed to set the read-only variable and aborted the restoration with
this message:
Variable Check ReadOnly variable fail Write Protected - 04B37FE8-F6AE-480B-BDD5-37D98C5E89AA:VarErrorFlag
Since it's a read-only variable maintained by the firmware, it's
pointless to restore the previous value, so the check can be
relaxed to allow EFI_WRITE_PROTECTED returned from SetVariable.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Gary Lin <glin@suse.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
"SerializeVariablesLib.h" is pure LF, while "SerializeVariablesLib.c" is
mixed (its only CRLF terminators are from commit e678f9db89). Convert
them both with "unix2dos".
"git show -b" produces no code hunks for this patch. Due to its simple and
mechanic nature (and because it blocks the application of another patch),
it's being committed without review.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
This patch is used to remove the status check for SockProcessRcvToken.
It's not return EFI_STATUS.
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
GenFds GenSection will search the output file based on the file extension.
If the output file has no extension, it should be skip.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Andrew Fish <afish@apple.com>
According to edk2 commit
"MdeModulePkg/PciBus: do not improperly degrade resource"
and to the EFI_INCOMPATIBLE_PCI_DEVICE_SUPPORT_PROTOCOL definition in the
Platform Init 1.4a specification, a platform can provide such a protocol
in order to influence the PCI resource allocation performed by the PCI Bus
driver.
In particular it is possible instruct the PCI Bus driver, with a
"wildcard" hint, to allocate the 64-bit MMIO BARs of a device in 64-bit
address space, regardless of whether the device features an option ROM.
(By default, the PCI Bus driver considers an option ROM reason enough for
allocating the 64-bit MMIO BARs in 32-bit address space. It cannot know if
BDS will launch a legacy boot option, and under legacy boot, a legacy BIOS
binary from a combined option ROM could be dispatched, and fail to access
MMIO BARs in 64-bit address space.)
In platform code we can ascertain whether a CSM is present or not. If not,
then legacy BIOS binaries in option ROMs can't be dispatched, hence the
BAR degradation is detrimental, and we should prevent it. This is expected
to conserve the 32-bit address space for 32-bit MMIO BARs.
The driver added in this patch could be simplified based on the following
facts:
- In the Ia32 build, the 64-bit MMIO aperture is always zero-size, hence
the driver will exit immediately. Therefore the driver could be omitted
from the Ia32 build.
- In the Ia32X64 and X64 builds, the driver could be omitted if CSM_ENABLE
was defined (because in that case the degradation would be justified).
On the other hand, if CSM_ENABLE was undefined, then the driver could be
included, and it could provide the hint unconditionally (without looking
for the Legacy BIOS protocol).
These short-cuts are not taken because they would increase the differences
between the OVMF DSC/FDF files. If we can manage without extreme
complexity, we should use dynamic logic (vs. build time configuration),
plus keep conditional compilation to a minimum.
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
This completes the transition to the new BDS.
The FILE_GUID in "QemuBootOrderLib.inf" is intentionally not changed.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Gary Ching-Pang Lin <glin@suse.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
With OvmfPkg's original QemuBootOrderLib (and USE_OLD_BDS) gone, we no
longer need the BootOptionList parameter in the SetBootOrderFromQemu()
prototype. Update the library class header file (including the function's
documentation), and adapt the library instance and the call sites.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Gary Ching-Pang Lin <glin@suse.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
This library instance is no longer referenced.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Gary Ching-Pang Lin <glin@suse.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
This library instance is no longer referenced.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Gary Ching-Pang Lin <glin@suse.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reasons:
- USE_OLD_BDS requires duplicating updates between OVMF's library
instances that depend on USE_OLD_BDS being FALSE vs. TRUE. Examples:
d5aee61bfa OvmfPkg/QemuNewBootOrderLib: adapt Q35 SATA PMPN to UEFI
spec Mantis 1353
1da7616649 OvmfPkg/QemuBootOrderLib: adapt Q35 SATA PMPN to UEFI spec
Mantis 1353
- The Xen community has embraced the new BDS. Examples:
14b2ebc30c OvmfPkg/PlatformBootManagerLib: Postpone the shell
registration
49effaf26e OvmfPkg/PciHostBridgeLib: Scan for root bridges when
running over Xen
- OVMF doesn't build with "-D USE_OLD_BDS -D HTTP_BOOT_ENABLE" anyway, as
NetworkPkg/HttpBootDxe now requires UefiBootManagerLib:
50a65824c7 NetworkPkg: Use UefiBootManagerLib API to create load
option.
We (correctly) don't resolve UefiBootManagerLib when USE_OLD_BDS is
TRUE.
- The new BDS has been working well; for example it's the only BDS
available in ArmVirtPkg:
1946faa710 ArmVirtPkg/ArmVirtQemu: use MdeModulePkg/BDS
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Gary Ching-Pang Lin <glin@suse.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
The "UNIXGCC Debug" section happens to name PlatformBdsLib and
IntelFrameworkModulePkg's BdsDxe as examples. OVMF will soon stop offering
those even as a fallback option.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Gary Ching-Pang Lin <glin@suse.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
The following codes are useless and cause memory leak issues.
So now remove them.
Cc: Cecil Sheng <cecil.sheng@hpe.com>
Cc: Qiu Shumin <shumin.qiu@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
when user don't set TOOL_CHAIN_TAG and TARGET by –D Flag, then GenFds
would report failure for format:
FILE DATA = $(OUTPUT_DIRECTORY)/$(TARGET)_$(TOOL_CHAIN_TAG)/testfile
so this patch enhance to get the TOOL_CHAIN_TAG and TARGET value by
following priority (high to low): 1. the Macro value set by -D Flag;
2. Get the value by the -t/-b option. 3. get the value from target.txt
file. Besides, this patch also remove the error checking for missing
-t/-b option.
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Yonghong Zhu <yonghong.zhu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
1) RunSplitCommand() allocates the initial SplitStdOut via
CreateFileInterfaceMem(). Free SplitStdIn after the swap to fix
the memory leak.
2) In RunSplitCommand(), SplitStdOut is checked for equality with
StdIn. This cannot happen due to the if-check within the swap.
Hence remove it.
3) UefiMain() doesn't free SplitList. Delete all list entries and
reinitialize the list when in DEBUG. This does not include the
CreateFileInterfaceMem()-allocated SplitStd mentioned in 1), so
keep the ASSERT() until resolved.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Marvin Haeuser <Marvin.Haeuser@outlook.com>
Reviewed-by: Qiu Shumin <shumin.qiu@intel.com>
Update MSRs semaphores to the ones in allocated aligned semaphores
buffer. If MSRs semaphores is not enough, allocate one page more.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Update each CPU semaphores to the ones in allocated aligned
semaphores buffer.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Allocate each CPU semaphores in allocated aligned semaphores buffer.
And add it into semaphores structure.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Update all global semaphores to the ones in allocated aligned
semaphores buffer.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Move MP sync data initialization in front of the place that initialize
page table, because the page fault spin lock is allocated in
InitializeMpSyncData() while it is initialized in SmmInitPageTable().
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Get semaphores alignment/size requirement and allocate aligned
buffer for all global spin lock and semaphores.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Add more comments:
1) EDKII version safe string function is similar as the one C11.
2) If error is returned, the Destination is unmodified.
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
This patch updates the HTTP driver to initialize the local variable for NULL
and check the NULL pointer before dereference it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
The driver entry point calls gDS->SetMemorySpaceAttributes().
This interface may return EFI_NOT_AVAILABLE_YET when CPU Arch
protocol is not available.
So we need to list CpuArch protocol in its INF dependency section.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
When coreboot uses different baud rate from the default (115200), the
current BDS driver will not be able to enable serial console display
due to the inconsistent serial port PCD settings. By adding the
PlatformHookLib reference in the inf file, it will enforce the PCDs
to be aligned with what have been passed from coreboot.
Cc: Prince Agyeman <prince.agyeman@intel.com>
Cc: Lee Leahy <leroy.p.leahy@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Maurice Ma <maurice.ma@intel.com>
Reviewed by: Lee Leahy <leroy.p.leahy@intel.com>
Current CorebootPayloadPkg uses PciBusNoEnumerationDxe and
PciRootBridgenoEnumerationDxe copied from the DuetPkg. Now it will
switch to use the standard PciBusDxe and PciHostBridgeDxe from
MdeModulePkg. As a result, a coreboot specific PciHostBridgeLib
is added to collect pre-allocated PCI resources.
Cc: Prince Agyeman <prince.agyeman@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Maurice Ma <maurice.ma@intel.com>
Reviewed-by: Prince Agyeman <prince.agyeman@intel.com>
Fu, Siyuan
Hao Wu
Jeff Fan
Cohen, Eugene
Maurice Ma
Laszlo Ersek
Darbin Reyes
Michael Zimmermann
Gary Lin
Jiaxin Wu
Liming Gao
Dandan Bi
Yonghong Zhu
Marvin H?user
Jiewen Yao
Fu Siyuan
Ruiyu Ni