Conform to the specification for GetStatus(), which states that "if
there are no transmit buffers to recycle and TxBuf is not NULL, *TxBuf
will be set to NULL".
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Now that the LAN9118-specific MMIO accessors provide the required
delays, remove the redundant stalls.
Stalls in delay loops are kept, as these give time for work to happen
beyond synchronisation of the device register file.
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Migrate the existing code to use the new LAN9118 MMIO wrappers, ensuring
that timing requirements are respected.
The newly redundant stalls will be removed in a subsequent patch.
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Commit a4626006bb ("EmbeddedPkg/Lan9118Dxe: use MemoryFence")
replaced some stalls with memory fences, on the presumption that these
were erroneously being used to order memory accesses. However, this was
not the case.
LAN9118 devices require a timing delay between state-changing
reads/writes and subsequent reads, as updates to the register file are
asynchronous and the effects of state-changes are not immediately
visible to subsequent reads.
This delay cannot be ensured through the use of memory barriers, which
only enforce observable ordering, and not timing. Thus, converting these
stalls to memory fences was erroneous, and may result in stale values
being read.
This reverts commit a4626006bb.
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
This patch makes a few minor DEBUG output changes:
- Fix typo in DEBUG output: Negociation->Negotiation
- Change DEBUG occurrences of "Lan9118" to "LAN9118" to make grepping
the log output easier.
- Change the warning that auto-negotiation is not supported when
AutoNegotiate() returns an error.
The function already reports if the feature is supported or not and
can also return an error for other reasons.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
When reviewing my LAN9118 driver PCD patch [1], Ard Biesheuvel noted
that most calls to gBS->Stall() in this driver seem to be used to
prevent timing issues between the device updating data and the host
reading the values. And that replacing most of these calls with a
MemoryFence() would be more robust.
The only exceptions are the stalls that are enclosed inside retry loops:
- in the AutoNegotiate() function.
This stall is waiting for the link to negotiate, which may require
stalling until it is ready.
- in the Lan9118Initialize() function.
These two stalls are waiting for devices and time out after a number
of retries.
- in the SoftReset() function.
This stall is inside a loop where the comment states:
"If time taken exceeds 100us, then there was an error condition"
In these instances, I kept the stall, but also added a MemoryFence().
[1] http://article.gmane.org/gmane.comp.bios.edk2.devel/7389
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Spurious error might appear during network transaction,
ignore them when there are not relevant.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <Ronald.Cron@arm.com>
Reviewed-by: Olivier Martin <Olivier.Martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18028 6f19259b-4bc3-4df7-8a09-765794883524
The Lan9118 driver did not recover after a receiver error as the error
handling code stopped the transmitter but did not restart it. Added the
restart of the transmitter.
Added also the restart of the receiver after a transmitter error and
the reactivation of the LEDs after all resets.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <ronald.cron@arm.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17106 6f19259b-4bc3-4df7-8a09-765794883524
The UEFI specification does not require the initialisation and reset
interface to check if an Ethernet cable is connected or not, and provides
the GetStatus() interface to do this. Furthermore, the 'Managed Network
Protocol' take care of the cable connection check in edk2 network stack.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <ronald.cron@arm.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16326 6f19259b-4bc3-4df7-8a09-765794883524
Correct the setting of the hardware filters according to what it asked
to the driver through the ReceiveFilters() interface function.
Keep track of the hardware settings in the "ReceiveFilterSetting" field of
the EFI_SIMPLE_NETWORK_MODE structure.
From now, after initialization, all filters are disabled and thus no packet
received.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <ronald.cron@arm.com>
Reviewed-By: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16243 6f19259b-4bc3-4df7-8a09-765794883524
Add or fix checking of the input parameters of the functions that constitute
the EFI_SIMPLE_NETWORK_PROTOCOL interface provided by the LAN9118 driver.
In case of invalid calls, the returned error codes are now compliant with the
UEFI specificationi and the SCT tests checking for those error codes do not
fail anymore.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <ronald.cron@arm.com>
Reviewed-By: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16239 6f19259b-4bc3-4df7-8a09-765794883524
TxBuff argument is optional in SNP.GetStatus(). This argument can be NULL.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16236 6f19259b-4bc3-4df7-8a09-765794883524
- Make the function PhySoftReset() return EFI_STATUS
- EFI_STATUS was treated as a signed integer by the caller which is not correct.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15630 6f19259b-4bc3-4df7-8a09-765794883524
Gary Lin
Michael Brown
Mark Rutland
Ryan Harkin
Ronald Cron
Olivier Martin