The ArmGicAcknowledgeInterrupt () returns the value returned by the
Interrupt Acknowledge Register and the InterruptID separately in an out
parameter.
The function documents the following: 'InterruptId is returned
separately from the register value because in the GICv2 the register
value contains the CpuId and InterruptId while in the GICv3 the register
value is only the InterruptId.'
This function skips setting the InterruptId in the out parameter for
GICv3. Although the return value from the function is the InterruptId
for GICv3, this breaks the function usage model as the caller expects
the InterruptId in the out parameter for the function. e.g. The caller
may end up using the InterruptID which could potentially be an
uninitialised variable value.
Therefore, set the InterruptID in the function out parameter for GICv3
as well.
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
According to the GIC architecture version 3 and 4 specification, the
maximum number of INTID bits supported in the CPU interface is 24.
Considering this the RegShift variable is not required to be more than 8
bits. Therefore, make the RegShift variable type to UINT8. Also add
necessary typecasts when calculating the RegOffset and RegShift values.
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
GICD_SGIR is a 32-bit register, of which INTID is bits [3:0] and Bits
[14:4] is RES0. Since SgiId parameter in the function ArmGicSendSgiTo ()
is UINT8, mask unused bits of SgiId before writing to the GICD_SGIR
register to prevent accidental setting of the RES0 bits.
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
The CPU Interface Identification Register (GICC_IIDR) is a 32-bit
register. Since ArmGicGetInterfaceIdentification () returns the value
read from the GICC_IIDR register, update the return type for this
function to UINT32.
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
The Software Generated Interrupt Register (GICD_SGIR) is a 32 bit
register with the following bit assignment:
TargetListFilter, bits [25:24]
CPUTargetList, bits [23:16]
NSATT, bit [15]
SGIINTID, bits [3:0]
Therefore, modify the TargetListFilter, CPUTargetList, SGI Interrupt ID
parameters of the ArmGicSendSgiTo () to use UINT8 instead of INTN.
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
The data type used by variables representing the
GicInterruptInterfaceBase has been inconsistently used in the ArmGic
driver and the library. The PCD defined for the GIC Interrupt interface
base address is UINT64. However, the data types for the variables used
is UINTN, INTN, and at some places UINT32.
Therefore, update the data types to use UINTN and add necessary
typecasts when reading values from the PCD. This should then be
consistent across AArch32 and AArch64 builds.
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
The data type used by variables representing the GicDistributorBase has
been inconsistently used in the ArmGic driver and the library. The PCD
defined for the GIC Distributor base address is UINT64. However, the
data types for the variables used is UINTN, INTN, and at some places
UINT32.
Therefore, update the data types to use UINTN and add necessary
typecasts when reading values from the PCD. This should then be
consistent across AArch32 and AArch64 builds.
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
The issue appears to have been introduced by:
41fb5d46 : ArmPkg/ArmGic: Use the GIC Redistributor instead of GIC Distributor for GICv3
The changes to ArmGicIsInterruptEnabled() introduced the error where the Boolean
result is assigned to Interrupts, but then the bit position check is performed
again (against the computed Boolean result instead of the interrupt mask) during
the return statement.
Fix removes erroneous test and relies on boolean test made at return.
Signed-off-by: Robbie King <robbiek@xsightlabs.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3737
Apply uncrustify changes to .c/.h files in the ArmPkg package
Cc: Andrew Fish <afish@apple.com>
Cc: Leif Lindholm <leif@nuviainc.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Signed-off-by: Michael Kubacki <michael.kubacki@microsoft.com>
Reviewed-by: Andrew Fish <afish@apple.com>
Bugzilla: 3415 (https://bugzilla.tianocore.org/show_bug.cgi?id=3415)
The GICv3 architecture supports up to 1020 ordinary interrupt
lines. The actual number of interrupts supported is described by the
ITLinesNumber field in the GICD_TYPER register. The total number of
implemented registers is normally calculated as
32*(ITLinesNumber+1). However, maximum value (0x1f) is a special case
since that would indicate that 1024 interrupts are implemented.
Add handling for this special case in ArmGicGetMaxNumInterrupts.
Signed-off-by: Andreas Sandberg <andreas.sandberg@arm.com>
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
The register address of GICR_IPRIORITYR is in SGI_base frame. Add
IPRIORITY_ADDRESS macro for getting GICR_IPRIORITYR address. Otherwise
GIC RAS error(Uncorrected software error) may report in ArmGicDxe.
This resolves BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3236
Signed-off-by: Ming Huang <huangming@linux.alibaba.com>
Reviewed-by: Leif Lindholm <leif@nuviainc.com>
Tested-by: Ard Biesheuvel <ardb@kernel.org> # QEMU/kvm guest on ThunderX2
Tested-by: Quan Nguyen <quan@os.amperecomputing.com>
Modify two macros to put "offset" in parentheses and remove
parentheses from "4 * offset".
Signed-off-by: Ming Huang <huangming@linux.alibaba.com>
Reviewed-by: Leif Lindholm <leif@nuviainc.com>
According to ARM IHI 0069F, section 11.9.18 GICD_IPRIORITYR<n>,
Interrupt Priority Registers, n = 0 - 254, when affinity routing is
enabled for the Security state of an interrupt, GICR_IPRIORITYR<n>
is used instead of GICD_IPRIORITYR<n> where n = 0 to 7 (that is, for
SGIs and PPIs).
As setting interrupt priority for SGIs and PPIs are handled using
difference registers depends on the mode, this patch instroduces
ArmGicSetInterruptPriority() helper function to handle the discrepancy.
Cc: Leif Lindholm <leif@nuviainc.com>
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Reviewed-off-by: Ard Biesheuvel <ard.biesheuvel@arm.com>
Updated Redistributor base calculation to allow for the fact that
GICv4 has 2 additional 64KB frames (for VLPI and a reserved frame).
The code now tests the VLPIS bit in the GIC Redistributor Type
Register (GICR_TYPER) and calculates the Redistributor granularity
accordingly.
The code changes are:
GICR_TYPER register fields, etc, added to the header.
Loop updated to pay attention to GICR_TYPER.Last.
Derive frame "stride" size from GICR_TYPER.VLPIS.
Note: The assumption is that the redistributors are adjacent for
all CPUs. However this may not be the case for NUMA systems.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The ArmGicLib API function GicGetCpuRedistributorBase () declares
GicCpuRedistributorBase to iterate over the redistributors of all
CPUs, but then inadvertently advances GicRedistributorBase instead.
Reported-by: "Oliyil Kunnil, Vishal" <vishalo@qti.qualcomm.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Unlike SGIs and PPIs, which are private to the CPU and are managed at
the redistributor level (which is also a per-CPU construct), shared
interrupts (SPIs) are shared between all CPUs, and therefore managed at
the distributor level (just as on GICv2).
Reported-by: Narinder Dhillon <ndhillonv2@gmail.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Before splitting off ArmGicArchLib and moving it out of
ArmPkg/Drivers/ArmGic into ArmPkg/Library, make sure that the
GIC specific declarations it depends on are not hidden away in
local headers "GicV2/GicV2Lib.h" and "GicV3/GicV3Lib.h".
So merge them with <Library/ArmGicLib.h>. This is entirely
appropriate, since this is not a header that declares a public
interface into ArmGicLib, but defines implementation internals.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18097 6f19259b-4bc3-4df7-8a09-765794883524
The GICv3 driver must use native mode to drive a GICv3 due to
the fact that v2 compatibility is optional in the v3 spec.
However, if v2 compatibility is implemented, it is the default
and needs to be disabled first by setting the Affinity Routing
Enable (ARE) bit.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
[added PCD that allows forcing the GICv3 driver to drive the GIC in v2 mode]
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Tested-by: Ard Biesheuvel <ard@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16875 6f19259b-4bc3-4df7-8a09-765794883524
GICv3 controller with no GICv2 legacy support must use the GIC
Redistributor registers instead of the GIC Distributor registers
for some operations (eg: enable/disable interrupts).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Tested-by: Ard Biesheuvel <ard@linaro.org>
Reviewed-by: Ard Biesheuvel <ard@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16874 6f19259b-4bc3-4df7-8a09-765794883524
CPU GIC Registributors are located next to each other in the GIC Redistributor
space.
The CPU GIC Redistributor is identified by its CPU affinity Aff3.Aff2.Aff1.Aff0.
This function returns the base address of the GIC Redistributor of
the calling CPU.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Tested-by: Ard Biesheuvel <ard@linaro.org>
Reviewed-by: Ard Biesheuvel <ard@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16873 6f19259b-4bc3-4df7-8a09-765794883524
This function returns the revision of the GIC Architecture.
Some GICv3 controllers can work in GICv2 mode. Switching to an
older GIC revision is driven by the higher level exception level.
This function allows code to support any GIC revision at runtime.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16231 6f19259b-4bc3-4df7-8a09-765794883524
The InterruptId has a different width for GicV2 and GicV3 (respectively
10bit and 24bit).
The function prototype has been changed to return this value to make the
caller GIC architecture version independent. Otherwise, we would have need
to expose a different mask to allow the caller to retrieve this value from
the read register.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15628 6f19259b-4bc3-4df7-8a09-765794883524
The support for GIcV2 was already existing. This change separate the GicV2
specific functions from the common Gic code (in preparation for GicV3 support).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15626 6f19259b-4bc3-4df7-8a09-765794883524
The implementation is the same when we run in Secure or Non-Secure world.
This change makes this function available for ArmGicSec.inf and ArmGicNonSec.inf.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15625 6f19259b-4bc3-4df7-8a09-765794883524
... and also rename the ArmGicLib sources to use an explicit 'Lib' suffix.
The renaming did not work well with SVN. Files were missing from the initial commit.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@15622 6f19259b-4bc3-4df7-8a09-765794883524
Sami Mujawar
Robbie King
Michael Kubacki
Andreas Sandberg
Ming Huang
Quan Nguyen
Michael D Kinney
Evan Lloyd
Ard Biesheuvel
Olivier Martin
Ronald Cron