When source level debug is enabled, but debug cable is not connected,
XhcResetHC() in XhciReg.c will reset the host controller, the debug
capability registers will be also reset. After the code in
InitializeUsbDebugHardware() sets DCE bit and LSE bit to "1" in DCCTRL,
there will be DMA on 0 (the value of some debug capability registers
for data transfer is 0) address buffer, fault info like below will
appear when IOMMU based on VTd is enabled.
VER_REG - 0x00000010
CAP_REG - 0x00D2008C40660462
ECAP_REG - 0x0000000000F050DA
GSTS_REG - 0xC0000000
RTADDR_REG - 0x0000000086512000
CCMD_REG - 0x2800000000000000
FSTS_REG - 0x00000002
FECTL_REG - 0xC0000000
FEDATA_REG - 0x00000000
FEADDR_REG - 0x00000000
FEUADDR_REG - 0x00000000
FRCD_REG[0] - 0xC0000006000000A0 0000000000000000
Fault Info - 0x0000000000000000
Source - B00 D14 F00
Type - 1 (read)
Reason - 6
IVA_REG - 0x0000000000000000
IOTLB_REG - 0x1200000000000000
This patch is to return error for the case.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
de8373fa07 could not handle two cases.
1. For the case that the USB3 debug port instance and DMA buffers are
from PEI HOB with IOMMU enabled, it was to reallocate the DMA buffers
by AllocateAddress with the memory type accessible by SMM environment.
But reallocating the DMA buffers by AllocateAddress may fail.
2. At S3 resume, after the code is transferred to PiSmmCpuDxeSmm from
S3Resume2Pei, HOB is still needed to be used for DMA operation, but
PiSmmCpuDxeSmm has no way to get the HOB at S3 resume.
The patch is to re-support IOMMU.
For PEI, allocate granted DMA buffer from IOMMU PPI, register IOMMU PPI
notification to reinitialize hardware with granted DMA buffer if IOMMU
PPI is not present yet.
For DXE, map DMA buffer by PciIo in PciIo notification for early DXE,
and register DxeSmmReadyToLock notification to reinitialize hardware
with granted DXE DMA buffer accessible by SMM environment for late DXE.
DebugAgentLib has been managing the instance as Handle in
HOB/SystemTable. The Handle(instance) from DebugAgentLib can be used
directly in DebugCommunicationLibUsb3. Then DebugCommunicationLibUsb3
could get consistent Handle(instance) from DebugAgentLib.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Fix GCC build failures below.
variable 'EvtTrb' set but not used [-Werror=unused-but-set-variable]
variable 'Index' set but not used [-Werror=unused-but-set-variable]
The build failure could only be caught with -D SOURCE_DEBUG_USE_USB3
build flag.
ad6040ec9b needs to be also reverted
when reverting IOMMU support patches, otherwise there will be conflict.
This patch is to re-do ad6040ec9b.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Fix GCC build failures below.
variable 'EvtTrb' set but not used [-Werror=unused-but-set-variable]
variable 'Index' set but not used [-Werror=unused-but-set-variable]
The build failure could only be caught with -D SOURCE_DEBUG_USE_USB3
build flag.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
For avoiding function name confliction,
rename IsBsp to DebugAgentIsBsp.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=573https://bugzilla.tianocore.org/show_bug.cgi?id=796
The same issue is reported again by GCC. Resend this patch again.
This patch renames the duplicated function name to fix it.
The SecPeiDebugAgentLib uses the global variable
mMemoryDiscoveredNotifyList for a PPI notification on
the Memory Discovered PPI. This same variable name is
used in the DxeIplPeim for the same PPI notification.
The XCODE5 tool chain detects this duplicate symbol
when the OVMF platform is built with the flag
-D SOURCE_DEBUG_ENABLE.
The fix is to rename this global variable in the
SecPeiDebugAgentLib library.
Cc: Andrew Fish <afish@apple.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
In enter SMI, APIC timer may be initialized. After exit SMI, APIC timer
will be restore.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Liming Gao <liming.gao@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
PI 1.6 has supported pre permanent memory page allocation,
to make sure the allocated memory is physical memory for DMA,
the patch is to check memory discovered PPI installed or not first
before calling AllocatePages.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
V3 changes:
Add detailed description for the usage of the Pcd in package DEC file.
Update the comment for the introduced Pcd in module INF files.
V2 changes:
Instead of using a global variable, use a Pcd for transfer protocol
revision.
Previously, the revision of the debug agent transfer protocol is
reflected by a macro.
This commit introduces a Pcd to reflect the revision in order to avoid the
comparison of two macros, which will generate a constant result detected
by code checkers.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=642
Add top level License.txt file with the BSD 2-Clause
License that is used by the majority of the EKD II open
source project content. Merge copyright statements
from the BSD 2-Clause License files in each package
directory and remove the duplication License.txt
file from package directories.
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Andrew Fish <afish@apple.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
https://bugzilla.tianocore.org/show_bug.cgi?id=629
Move Contributions.txt that contains the TianoCore
Contribution Agreement 1.0 to the root of the edk2
repository and remove the duplicate Contributions.txt
files from all packages.
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Andrew Fish <afish@apple.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
There are cases that the operands of an expression are all with rank less
than UINT64/INT64 and the result of the expression is explicitly cast to
UINT64/INT64 to fit the target size.
An example will be:
UINT32 a,b;
// a and b can be any unsigned int type with rank less than UINT64, like
// UINT8, UINT16, etc.
UINT64 c;
c = (UINT64) (a + b);
Some static code checkers may warn that the expression result might
overflow within the rank of "int" (integer promotions) and the result is
then cast to a bigger size.
The commit refines codes by the following rules:
1). When the expression is possible to overflow the range of unsigned int/
int:
c = (UINT64)a + b;
2). When the expression will not overflow within the rank of "int", remove
the explicit type casts:
c = a + b;
3). When the expression will be cast to pointer of possible greater size:
UINT32 a,b;
VOID *c;
c = (VOID *)(UINTN)(a + b); --> c = (VOID *)((UINTN)a + b);
4). When one side of a comparison expression contains only operands with
rank less than UINT32:
UINT8 a;
UINT16 b;
UINTN c;
if ((UINTN)(a + b) > c) {...} --> if (((UINT32)a + b) > c) {...}
For rule 4), if we remove the 'UINTN' type cast like:
if (a + b > c) {...}
The VS compiler will complain with warning C4018 (signed/unsigned
mismatch, level 3 warning) due to promoting 'a + b' to type 'int'.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Current SmmDebugAgentLib will initialize IDT table to support source debugging
at each time SMI entry on SMM BSP. Actually, we only need to initialize IDT
table at first time SMI entry.
Add one flag to avoid re-initializing IDT table.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
#define MSR_IA32_APIC_BASE_ADDRESS is duplicated with #define MSR_IA32_APIC_BASE
defined in UefiCpuPkg/Include/Register/ArchitecturalMsr.h, so we could remove it
and update the modules to use MSR_IA32_APIC_BASE from ArchitecturalMsr.h.
Structure MSR_IA32_APIC_BASE conflicts with #define MSR_IA32_APIC_BASE defined
in UefiCpuPkg/Include/Register/ArchitecturalMsr.h, so we could remove it and
update the modules to use structure MSR_IA32_APIC_BASE_REGISTER from
ArchitecturalMsr.h.
v5:
1. Update SourceLevelDebugPkg to use APIC Base MSR from ArchitecturalMsr.h.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
Add the following definition in the [BuildOptions] section in package DSC
files to disable APIs that are deprecated:
[BuildOptions]
*_*_*_CC_FLAGS = -D DISABLE_NEW_DEPRECATED_INTERFACES
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
The BaseTools/Scripts/ConvertMasmToNasm.py script was used to convert
X64/AsmFuncs.asm to X64/AsmFuncs.nasm.
And, manually update the wrong replacement with 0H.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
The BaseTools/Scripts/ConvertMasmToNasm.py script was used to convert
Ia32/AsmFuncs.asm to Ia32/AsmFuncs.nasm.
And, manually update the wrong replacement with 0H.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
The BaseTools/Scripts/ConvertMasmToNasm.py script was used to convert
X64/IntHandler.asm to X64/IntHandler.nasm.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
The BaseTools/Scripts/ConvertMasmToNasm.py script was used to convert
Ia32/IntHandler.asm to Ia32/IntHandler.nasm.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
mMailboxPointer is used before it is initialization. This issue only happens
when SmmDebugAgent is initialized without PeiDebugAgent or DxeDebugAgent
initialization. The fix is to use Mailbox instead.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Update the local variable type to avoid potential data overflow.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Hao Wu <hao.wu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19734 6f19259b-4bc3-4df7-8a09-765794883524
DxeDebugAgentLib instance produces gEfiDebugAgentGuid system table.
Its usage should be PRODUCES instead of SOMETIMES_PRODUCES.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19316 6f19259b-4bc3-4df7-8a09-765794883524
To convert these files I ran:
$ python3 BaseTools/Scripts/ConvertUni.py SourceLevelDebugPkg
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19263 6f19259b-4bc3-4df7-8a09-765794883524
Update DebugAgent to make sure the Local APIC SoftwareEnable bit is set
before using the Local APIC Timer.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18712 6f19259b-4bc3-4df7-8a09-765794883524
Actually, TimerCycle is APIC timer's initial count. Timer count value 0 is
missed when calculating Delta value.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18329 6f19259b-4bc3-4df7-8a09-765794883524
If CPU runs fast and timer runs slow, two GetApicTimerCurrentCount() may return
the same timer count value. We need to consider timer roll-over not happened.
Otherwise, one false timeout flag will be set.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18328 6f19259b-4bc3-4df7-8a09-765794883524
In DEBUG_AGENT_INIT_POSTMEM_SEC case, caller may disable/restore CPU interrupt
to protect the stack/heap migration. SecPeiDebugAgentLib cannot always enable
CPU interrupt. Otherwise system may crash during stack/heap migration.
SecPeiDebugAgentLib should restore original CPU interrupt state in
DEBUG_AGENT_INIT_POSTMEM_SEC case.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Brian J. Johnson <bjohnson@sgi.com>
Tested-by: Brian J. Johnson <bjohnson@sgi.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17916 6f19259b-4bc3-4df7-8a09-765794883524
Recent changes to debug timer initialization (commit 2befbc82, svn 17572)
modified the Sec/Pei InitializeDebugAgent() routine to enable debug timer
interrupts. This causes problems in the DEBUG_AGENT_INIT_POSTMEM_SEC case:
the callers appear to assume that if they block timer interrupts before the
call, interrupts will remain blocked afterwards.
It is not always safe to have interrupts enabled on return from
InitializeDebugAgent(). For instance, after calling InitializeDebugAgent(),
OvmfPkg's TemporaryRamMigration() moves the stack, heap, and IDT to RAM, then
switches to the new stack. Only then does it reenable timer interrupts.
Taking an interrupt during this process can corrupt state, causing crashes.
Do not unmask the debug timer interrupt in the DEBUG_AGENT_INIT_POSTMEM_SEC
case.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Brian J. Johnson <bjohnson@sgi.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17893 6f19259b-4bc3-4df7-8a09-765794883524
Recent changes to debug timer handling ended up leaving the timer disabled in
PEI. This made it impossible to stop execution in PEI externally via the
debugger. Enable the timer when InitializeDebugAgent calls
InitializeDebugAgentPhase2, as well as when it returns directly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Brian J. Johnson <bjohnson@sgi.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17819 6f19259b-4bc3-4df7-8a09-765794883524
Star Zeng
Liming Gao
Michael Kinney
Hao Wu
Jeff Fan
Gary Lin
Laszlo Ersek
Eric Dong
Jordan Justen
Ruiyu Ni
Qiu Shumin
Brian J. Johnson