If PcdDxeNxMemoryProtectionPolicy is set to enable protection for memory
of EfiBootServicesData, EfiConventionalMemory, the BIOS will reset after
timer initialized and started.
The root cause is that the memory used to hold the exception and interrupt
handler is allocated with type of EfiBootServicesData and marked as
non-executable due to NX feature enabled. This patch fixes it by allocating
EfiBootServicesCode type of memory for those handlers instead.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
If PcdDxeNxMemoryProtectionPolicy is set to enable protection for memory
of EfiBootServicesCode, EfiConventionalMemory, the BIOS will hang at a page
fault exception during MP initialization.
The root cause is that the AP wake up buffer, which is below 1MB and used
to hold both AP init code and data, is type of EfiConventionalMemory (not
really allocated because of potential conflict with legacy code), and is
marked as non-executable. During the transition from real address mode
to long mode, the AP init code has to enable paging which will then cause
itself a page fault exception because it's just running in non-executable
memory.
The solution is splitting AP wake up buffer into two part: lower part is
still below 1MB and shared with legacy system, higher part is really
allocated memory of BootServicesCode type. The init code in the memory
below 1MB will not enable paging but just switch to protected mode and
jump to higher memory, in which the init code will enable paging and
switch to long mode.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
In 32-bit mode, the BIOS will not create page table for memory beyond
4GB and therefore it cannot handle the attributes change request for
those memory. But current CpuDxe doesn't check this situation and still
try to complete the request, which will cause attributes of incorrect
memory address to be changed due to type cast from 64-bit to 32-bit.
This patch fixes this issue by checking the end address of input
memory block and returning EFI_UNSUPPORTED if it's out of range.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
We also got maybe-uninitialized warning when building OpensslLib.inf
with GCC48 for ARM and AARCH64, so add -Wno-error=maybe-uninitialized
build option just as other platforms.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Cc: Qin Long <qin.long@intel.com>
Cc: Ting Ye <ting.ye@intel.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Qin Long <qin.long@intel.com>
XCODE5 doesn't support absolute addressing in the assembly code.
This change uses lea instruction to get the address.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Liming Gao <liming.gao@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
A submodule allows to keep another Git repository in a subdirectory
of main repository. The submodule repository has its own history, which
does not interfere with the history of the current repository. This can
be used to have external dependencies such as third party libraries.
After the extra patch for EDKII-OpenSSL build was removed, OpenSSL can
be one typical submodule use case in EDKII project. This patch adds the
openssl git repository into EDKII project as one submodule.
One .gitmodules file will be generated with the submodule info:
[submodule "CryptoPkg/Library/OpensslLib/openssl"]
path = CryptoPkg/Library/OpensslLib/openssl
url = https://github.com/openssl/openssl
The user can use the following command to clone both main EDKII repo and
openssl submodule:
1) Add the "--recursive" flag to their git clone command:
$ git clone --recursive https://github.com/tianocore/edk2
or 2) Manually initialize and the submodules after the clone operation:
$ git clone https://github.com/tianocore/edk2
$ git submodule update -–init -–recursive
For Pull operations, "git pull" will not update the submodule repository.
So the following combined commands can be used to pull the remote submodule
updates (e.g. Updating to new supported OpenSSL release)
$ git pull –-recurse-submodules && \
git submodule update -–recursive --remote
Cc: Ye Ting <ting.ye@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Qin Long <qin.long@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Fix DMA does not work issue when system memory is not
greater than 4G.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Commits a2ea6894e6
* UefiCpuPkg/MpInitLib: Fix a bug that AP enters timer INT handler
masked the interrupts in AP.
But it didn't unmask the interrupt in new BSP when Switch BSP
happens.
The patch fixed this issue.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jeff Fan <vanjeff_919@hotmail.com>
Cc: Eric Dong <eric.dong@intel.com>
Get high top by host address width instead of resource HOB.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
mVtdHostAddressWidthMask is not been used at all,
its definition and related code could be removed.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
According to VTd spec, HostAddressWidth + 1 should be used as the real
host address width value.
Host Address Width:
This field indicates the maximum DMA physical
addressability supported by this platform. The
system address map reported by the BIOS
indicates what portions of this addresses are
populated.
The Host Address Width (HAW) of the platform is
computed as (N+1), where N is the value
reported in this field. For example, for a platform
supporting 40 bits of physical addressability, the
value of 100111b is reported in this field.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
According to VTd spec, the real hardware decoded limit should be
PHMR/PLMR.Limit value + alignment value.
"Bits N:0 of the limit register are
decoded by hardware as all 1s."
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
* In DxeIpIo, an ASSERT check is incorrectly used in IpIoAddIp(), which result
debug image hang when this API is called, this patch is to fix this issue.
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Wang Fan <fan.wang@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Ovmf appended option -mno-mmx -mno-sse, but these two options were enabled
in Openssl. The compiler option becomes -mmmx ?msse -mno-mmx -mno-sse. It
trig mac clang compiler hang when compile one source file in openssl.
This issue is found when SECURE_BOOT_ENABLE is TRUE. This may be the compiler
issue. To work around it, don't add these two options for XCODE5 tool chain.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Liming Gao <liming.gao@intel.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=849
In V2, use "mov rax, strict qword 0" to replace the hard code db.
1. Use lea instruction to get the address instead of mov instruction.
2. Use the dummy address as jmp destination, and add the logic to fix up
the address to the absolute address at boot time.
3. On MpFuncs.nasm, use ExchangeInfo to record InitializeFloatingPointUnits.
This way is same to MpInitLib.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Liming Gao <liming.gao@intel.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=849
In V2, use "mov rax, strict qword 0" to replace the hard code db.
1. Use lea instruction to get the address instead of mov instruction.
2. Use the dummy address as jmp destination, and add the logic to fix up
the address to the absolute address at boot time.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Liming Gao <liming.gao@intel.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=849
In V2, use mov rax, strict qword 0 to replace the hard code db.
Use the dummy address as jmp destination, and add the logic to fix up
the address to the absolute address at boot time.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Liming Gao <liming.gao@intel.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
XCODE5 doesn't support absolute addressing in the assembly code.
This change uses lea instruction to get the address.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Liming Gao <liming.gao@intel.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Star Zeng <star.zeng@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Reported-by: Christian Ehrhardt <ehrhardt@genua.de>
Signed-off-by: Christian Ehrhardt <ehrhardt@genua.de>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Tested-by: Christian Ehrhardt <ehrhardt@genua.de>
The Graphics Output Protocol's mode information specifies the
PixelsPerScanLine property. Most of the time this is identical to
HorizontalResolution. However, due to alignment requirements etc. it
may be slightly larger. I.e. each scan line will have some "pixels"
that are not visible on the screen but consume space in the frame
buffer.
If the graphics output protocol correctly initializes
HorizontalResolution to 1366 and PixelsPerScanLine to 1376. As a
result the graphics output is broken.
If setting HorizontalResolution to 1376 instead, the output is fine
(except for 10 invisible pixels on the right of the screen).
The patch fixes this bug by using PixelsPerScanLine when calculating
the line width.
Contributed-under: TianoCore Contribution Agreement 1.1
Reported-by: Christian Ehrhardt <ehrhardt@genua.de>
Signed-off-by: Christian Ehrhardt <ehrhardt@genua.de>
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Christian Ehrhardt <ehrhardt@genua.de>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Tested-by: Christian Ehrhardt <ehrhardt@genua.de>
* In DxeIpIo, there are several places use ASSERT() to check input
parameters without and descriptions or error handling. This patch
fixed this issue.
* Fixed some incorrect descriptions in code commence.
* Remove unneeded Exit tag in function IpIoOpen and IpIoConfigIp.
* Add EFIAPI tag for function IpIoRefreshNeighbor.
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Wang Fan <fan.wang@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
* When the packet is not normal packet or icmp error packet, the code
does not recycle it by signal RecycleSignal event, and this will
result some memory leak. This patch is to fix this issue.
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Wang Fan <fan.wang@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
It didn't cause big issues when VT-d was disabled.
But in VT-d enabled platform, lack of EhcFreeUrb call caused
the DMA data was not moved back to user's buffer.
It caused the correct data cannot be got through sync interrupt
transfer.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The implementation of MdeModulePkg\Universal\Acpi\AcpiTableDxe reserves
first entry of RSDT/XSDT to FADT, the first entry value is 0 when FADT
is not installed. So the RSDT/XSDT parsing code should check the entry
value first before checking the table signature.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Commit 2ac1730bf2 (MdeModulePkg/DxeIpl: Mark page table as read-only)
sets the memory pages used for page table as read-only after paging is
setup and sets CR0.WP to protect CPU modifying the read-only pages.
The commit causes #PF when MemEncryptSevClearPageEncMask() or
MemEncryptSevSetPageEncMask() tries to change the page-table attributes.
This patch takes the similar approach as Commit 147fd35c3e
(UefiCpuPkg/CpuDxe: Enable protection for newly added page table).
When page table protection is enabled, we disable it temporarily before
changing the page table attributes.
This patch makes use of the same approach as Commit 2ac1730bf2
(MdeModulePkg/DxeIpl: Mark page table as read-only)) for allocating
page table memory from reserved memory pool, which helps to reduce a
potential "split" operation.
The patch duplicates code from commit 147fd35c3e. The code duplication
will be removed after we implement page table manipulation library. See
bugzilla https://bugzilla.tianocore.org/show_bug.cgi?id=847.
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
We're currently building everything except for this file.
Since 'fdt_create_empty_tree' can be useful for some
platforms, compile this one too.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Michael Zimmermann <sigmaepsilon92@gmail.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
This currently isn't needed by anything in the edk2 tree but
it's useful for externally maintained platforms which have
to set this register e.g. to disable alignment aborts.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Michael Zimmermann <sigmaepsilon92@gmail.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Today's implementation prints nothing when the format string cannot
fit in the report status extended data buffer.
It confuses user.
The patch changes to print partial message by truncating the format
string when it's too long.
The missing enhancement is the extended data buffer only reserves 96
bytes for the var-args. When the format string is not very long but
contains 13 %lx or %p, the var-args buffer is too small. Today's
implementation prints nothing for this case.
This patch doesn't change such behavior.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
According to UEFI spec, the PXE.Mtftp() should return invalid parameter if the
BufferPtr parameter was NULL and the DontUseBuffer parameter was FALSE.
The DontUseBuffer is only used when perform MTFTP/TFTP read operation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
According to TCG PP1.3 spec, error PCR bank allocation input should be
rejected by Physical Presence. Firmware has to ensure that at least one
PCR banks is active.
Cc: Long Qin <qin.long@intel.com>
Cc: Yao Jiewen <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chao Zhang <chao.b.zhang@intel.com>
Reviewed-by: Long Qin <qin.long@intel.com>
Reviewed-by: Yao Jiewen <jiewen.yao@intel.com>
Type definition in UEFI & OpeenSSL is different. Sometime it could cause
write overflow. Should use same data type when accessing the same region
Cc: Long Qin <qin.long@intel.com>
Cc: Chen Chen <chen.a.chen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chao Zhang <chao.b.zhang@intel.com>
Reviewed-by: Long Qin <qin.long@intel.com>
Enhance MCA feature dependency check base on SDM pseudocode example 15-1.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Bell Song <binx.song@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Under a certain [outdated] GCC482 compiler, the new-added "-Wno-format"
flag will not take effect, and break the x86_64 build.
This is one known issue in some Ubuntu/GCC-4.8.2 environment, which will
overwrite "-Wno-format" with some default setting. see more information
and discussion from:
https://gcc.gnu.org/ml/gcc-help/2014-03/msg00003.htmlhttps://wiki.ubuntu.com/ToolChain/CompilerFlags
This patch adds one extra "-Wno-error=format" for gcc x86_64 builds to
suppress this warning.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Long Qin <qin.long@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
AllocateCodePages() is used to allocate buffer for IDT range,
the code pages will be set to RO in SetMemMapAttributes(),
then the code to set IDT range to RO in PatchGdtIdtMap() is
redundant and could be removed.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
When StackGuard is enabled on IA32, the #double fault exception
is reported instead of #page fault.
This issue does not exist on X64, or IA32 without StackGuard.
The fix at e4435f710c was incomplete.
It is because AllocateCodePages() is used to allocate buffer for
GDT and TSS, the code pages will be set to RO in SetMemMapAttributes().
But IA32 Stack Guard need use task switch to switch stack that need
write GDT and TSS, so AllocateCodePages() could not be used.
This patch uses AllocatePages() instead of AllocateCodePages() to
allocate buffer for GDT and TSS if StackGuard is enabled on IA32.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jian J Wang <jian.j.wang@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
* Since wireless network can switch at very short time, the time interval
of reconfig event checking is too long for this case. To achieve better
performance and scalability, separate this task from Ip4 tick timer.
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Wang Fan <fan.wang@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
* The library API use array elements without any index range check, this
patch is to fix this issue to avoid null pointer reference.
V2
* Added an ASSERT check for the case PrefixLength equals to IP6_PREFIX_MAX.
* Synced some code descriptions to head file.
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Wang Fan <fan.wang@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
In UDP6Dxe, there are several places that may be enhanced
to check input parameters and returned status. This patch
is to fix these issues.
Cc: Ye Ting <ting.ye@intel.com>
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Wang Fan <fan.wang@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
In UDP6Dxe, there are some coding style issues, this patch
is to fix these issues.
Cc: Ye Ting <ting.ye@intel.com>
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Wang Fan <fan.wang@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Jian J Wang
Heyi Guo
Liming Gao
Long Qin
Star Zeng
Ruiyu Ni
Wang Fan
Brijesh Singh
Michael Zimmermann
Yunhua Feng
Fu Siyuan
Zhang, Chao B
Song, BinX
Hao Wu