In OvmfPkgIa32X64.dsc:
Paraphrasing svn rev 13350: gPcAtChipsetPkgTokenSpaceGuid is declared in
PcAtChipsetPkg.dec and used via AcpiPlatformDxe.inf, but with the latest
build tools, since this package builds multiple architectures (IA32 & X64)
and AcpiPlatformDxe is used on X64 only, it is now necessary to place the
gPcAtChipsetPkgTokenSpaceGuid PCD's in the [PcdsFixedAtBuild.X64] section.
In the two other .dsc files:
Make a similar change to keep file contents more easily comparable.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
[jordan.l.justen@intel.com: change all .dsc files to keep them diffable]
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13724 6f19259b-4bc3-4df7-8a09-765794883524
I. There are at least three locations in OvmfPkg that manipulate the PMBA
and related PIIX4 registers.
1. MiscInitialization() [OvmfPkg/PlatformPei/Platform.c]
module type: PEIM -- Pre-EFI Initialization Module
(a) currently sets the PMBA only: 00.01.3 / 0x40 bits [15:6]
2. AcpiTimerLibConstructor() [OvmfPkg/Library/AcpiTimerLib/AcpiTimerLib.c]
module type: BASE -- probably callable anywhere after PEI
(a) sets the PMBA if needed: 00.01.3 / 0x40 bits [15:6]
(b) sets PCICMD/IOSE if needed: 00.01.3 / 0x04 bit 0
(c) sets PMREGMISC/PMIOSE: 00.01.3 / 0x80 bit 0
3. AcpiInitialization() [OvmfPkg/Library/PlatformBdsLib/BdsPlatform.c]
module type: DXE_DRIVER -- Driver eXecution Environment
(a) sets SCI_EN, which depends on correct PMBA setting from earlier
(
The relative order of #1 and #3 is dictated minimally by their module
types. Said relative order can be verified with the boot log:
27 Loading PEIM at 0x00000822320 EntryPoint=0x00000822580
PlatformPei.efi
28 Platform PEIM Loaded
1259 PlatformBdsInit
1270 PlatformBdsPolicyBehavior
Line 28 is printed by InitializePlatform()
[OvmfPkg/PlatformPei/Platform.c] which is the entry point of that
module. The other two lines are printed by the corresponding functions
in "OvmfPkg/Library/PlatformBdsLib/BdsPlatform.c".
)
Currently #2 (AcpiTimerLibConstructor()) is called in a random spot
(whenever it gets loaded from the firmware image) and masks the
insufficient setup in #1. We shouldn't depend on that, PEI should finish
with IO space being fully accessibe. In addition, PEI should program the
same PMBA value as AcpiTimerLib.
II. The PEI change notwithstanding, AcpiTimerLib should stay defensive and
ensure proper PM configuration for itself (either by confirming or by
doing).
III. Considering a possible cleanup/unification of #2 and #3: timer
functions relying on AcpiTimerLibConstructor(),
- MicroSecondDelay()
- NanoSecondDelay()
- GetPerformanceCounter()
- GetPerformanceCounterProperties()
- GetTimeInNanoSecond()
may be called before #3 is reached (in Boot Device Selection phase), so we
should not move the initialization from #2 to #3. (Again, AcpiTimerLib
should contain its own setup.)
We should also not move #3 to an earlier phase -- SCI_EN is premature
unless we're about to boot real soon ("enable generation of SCI upon
assertion of PWRBTN_STS, LID_STS, THRM_STS, or GPI_STS bits").
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13722 6f19259b-4bc3-4df7-8a09-765794883524
The Index Register Base Address bitfield is selected by the binary mask
00000000 00000000 11111111 11000000, 0xFFC0; fix the typo.
Reported-by: Gleb Natapov <gleb@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13720 6f19259b-4bc3-4df7-8a09-765794883524
When allocating the BLOCK_MMIO_TO_BLOCK_IO_DEVICE structure, we were
not allocating a large enough amount. We were allocating the size of
the pointer, rather than the size of the structure.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13688 6f19259b-4bc3-4df7-8a09-765794883524
Currently if SOURCE_DEBUG_ENABLE is enabled when building with
GCC44, then the SEC module will not fit into SECFV.
This change increases the size of SECFV to allow this.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13687 6f19259b-4bc3-4df7-8a09-765794883524
Set the boot order based on configuration retrieved from QEMU.
Attempt to retrieve the "bootorder" fw_cfg file from QEMU. Translate the
OpenFirmware device paths therein to UEFI device path fragments. Match the
translated fragments against the enumerated BootOptionList, and rewrite
the BootOrder NvVar so that it corresponds to the order described in
fw_cfg.
The user is expected to configure working boot options first.
Tested via virt-manager's boot order widget.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13683 6f19259b-4bc3-4df7-8a09-765794883524
Including the range of [0xFC000000, 0xFD000000) for PCI MMIO
allocation created a conflict for Xen's HVM loader.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13682 6f19259b-4bc3-4df7-8a09-765794883524
We don't force a platform reset for OVMF when PK is changed in
custom mode setup.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Lee Rosenbaum <lee.g.rosenbaum@intel.com>
Reviewed-by: Erik Bjorge <erik.c.bjorge@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13635 6f19259b-4bc3-4df7-8a09-765794883524
Represent the set of possible PCI link target IRQs with
Pcd8259LegacyModeEdgeLevel. This ensures that the 8259 Interrupt
Controller code in PcAtChipsetPkg will treat them as level-triggered too.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13628 6f19259b-4bc3-4df7-8a09-765794883524
Rotate links over devices and pins so that they match qemu.
PIIX4 function 3 (Power Management Module) unconditionally uses the INTA
interrupt pin. SCI from this module requires IRQ9.
Keep other assignments off IRQ9. Only IRQ5, IRQ10, IRQ11 remain for PCI
devices.
Bump OEMRevision in the DSDT.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13625 6f19259b-4bc3-4df7-8a09-765794883524
Kill PDIS and PSRS as they are writing to copies of PIR[A-D], not PIR[A-D]
themselves. Use specialized _DIS and _SRS methods that access PIR[A-D]
directly.
(This should be solvable by passing RefOf (PIRA) etc to PDIS/PSRS, however
the RHEL-6.3 kernel AML parser seems to choke on it. The rules described
in ACPIspec5.0 Table 19-316 "Object Storing and Copying Rules" don't seem
to work:
ACPI Error: Needed [Integer/String/Buffer], found [Reference]
ffff88003ee02420 (20090903/exresop-422)
ACPI Exception: AE_AML_OPERAND_TYPE, While resolving operands for
[OpcodeName unavailable] (20090903/dswexec-445)
ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.LPC_.PDIS] (Node ffff88003f638b50), AE_AML_OPERAND_TYPE
ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.LPC_.LNKA._DIS] (Node ffff88003f638a10),
AE_AML_OPERAND_TYPE
When changing the method too, so that it writes to DerefOf (Arg0) instead
of Arg0, ie. explicitly dereferencing rather than expecting the auto-deref
to work:
ACPI Error: Needed type [Reference], found [RegionField]
ffff88003f639858 (20090903/exresop-104)
ACPI Exception: AE_AML_OPERAND_TYPE, While resolving operands for
[OpcodeName unavailable] (20090903/dswexec-445)
ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.LPC_.PDIS] (Node ffff88003f638b50), AE_AML_OPERAND_TYPE
ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.LPC_.LNKA._DIS] (Node ffff88003f638a10),
AE_AML_OPERAND_TYPE
In short, when passing a RefOf, it is recognized as a reference inside the
method but mistakenly refused. When trying to deref it explicitly with
DerefOf, then it's suddenly not recognized as a reference.)
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13621 6f19259b-4bc3-4df7-8a09-765794883524
"RTC day of the month alarm feature is not supported".
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13614 6f19259b-4bc3-4df7-8a09-765794883524
- Qemu's PIIX emulation actually supports SMM and ACPI_ENABLE /
ACPI_DISABLE.
- After enabling SMI_CMD (SMI_CMD_IO_PORT), further values to be written
there must be synchronized with qemu: PSTATE_CNT, CST_CNT.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13611 6f19259b-4bc3-4df7-8a09-765794883524
"FWDT" ("firmware data") is allocated as EfiReservedMemoryType, with
AllocateReservedPool(). <MdePkg/Include/Library/MemoryAllocationLib.h>
doesn't seem to provide direct access to EfiACPIReclaimMemory, but at this
point the former seems sufficient.
Based on SeaBIOS commit 2062f2ba by Gerd Hoffmann <kraxel@redhat.com>.
v3:
- coding style fixes:
- BDAT -> FWDT
- __packed -> #pragma pack(1)
- BFLD -> FIRMWARE_DATA, PCI_WINDOW
- Bfld -> FwData
- Ssdt.asl: changed license to 2-clause BSDL, paraphrasing Dsdt.asl
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13573 6f19259b-4bc3-4df7-8a09-765794883524
Fix IO-APIC range size.
Add HPET.
Take LAPIC base from PCD and fix range size.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13572 6f19259b-4bc3-4df7-8a09-765794883524
ConSplitterDxe (UEFI_DRIVER) now uses this library class.
Move the library mapping to the common LibraryClasses section.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13570 6f19259b-4bc3-4df7-8a09-765794883524
UNIXGCC builds larger images than GCC44, and can have issues
fitting into the FD image. Therefore, when using UNIXGCC,
debug will be disabled by default.
The README file is updated with instructions for selectively
enabling debug for UNIXGCC.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13569 6f19259b-4bc3-4df7-8a09-765794883524
This patch adds support for a debug console on the same port that is used
by SeaBIOS. This makes it easier to debug OVMF, because it does not mix
debug and serial output on the same device. It also makes it easier to
leave some of the debug messages on even in release builds.
To enable it, pass "-debugcon stdio -global isa-debugcon.iobase=0x402" to
QEMU.
The new mechanism is enabled by default, but a regular serial console can
be chosen by adding -D DEBUG_ON_SERIAL_PORT to the build options.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
[jordan.l.justen@intel.com: MAX_DEBUG_MESSAGE_LENGTH=>0x100, p=>Ptr]
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13562 6f19259b-4bc3-4df7-8a09-765794883524
Tested with the "bootorder" fw_cfg file. Example contents (leading space
added and line terminators transcribed for readability):
/pci@i0cf8/ide@1,1/drive@0/disk@0<LF>
/pci@i0cf8/ide@1,1/drive@1/disk@0<LF>
/pci@i0cf8/ethernet@3/ethernet-phy@0<NUL>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13549 6f19259b-4bc3-4df7-8a09-765794883524
This patch adds Xen ACPI tables support to OVMF.
Use EFI_ACPI_TABLE_PROTOCOL to publish all Xen ACPI tables in OVMF,
while keeping the Qemu and KVM support.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Bei Guan <gbtju85@gmail.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13541 6f19259b-4bc3-4df7-8a09-765794883524
Older QEMU versions would load vgabios-cirrus.bin at 0xc0000 in
system RAM. We would then find this ROM, and try to run it, since
it would be our QEMU Video driver.
Now, the QEMU Video driver is just merged into the main OVMF
firmware image, so this support is unused.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13522 6f19259b-4bc3-4df7-8a09-765794883524
This enables qemu to use OVMF with a single -bios option. Based on
<http://lists.xen.org/archives/html/xen-devel/2012-03/msg01992.html>.
v1->v2:
- move xen-devel link from code to commit message
- cover all three FDF files
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
[jordan.l.justen@intel.com: remove vgabios-cirrus.bin from build.sh/README]
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13520 6f19259b-4bc3-4df7-8a09-765794883524
Update MADT processing for QEMU to add additional Local APIC
entries to the MADT.
The MADT is still built with a single Local APIC entry.
If the AcpiPlatformDxe driver determines that more processors
are available, then additional Local APIC entries are added
to the MADT at runtime.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13387 6f19259b-4bc3-4df7-8a09-765794883524
Detect QEMU & Xen, and allow each to choose how to publish
the individual ACPI tables.
Currently both paths simply publish the tables unmodified.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13385 6f19259b-4bc3-4df7-8a09-765794883524
This driver is currently a direct copy of
MdeModulePkg/Universal/Acpi/AcpiPlatformDxe.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13384 6f19259b-4bc3-4df7-8a09-765794883524
It is declared in SecurityPkg.dec, but with the latest build tools, since this package builds multiple architectures (IA32 & X64) and there are no IA32 modules used from the SecurityPkg, it is now necessary to place the gEfiSecurityPkgTokenSpaceGuid PCD's in a [PcdsFixedAtBuild.X64] section.
Signed-off-by: lee.g.rosenbaum@intel.com
Reviewed-by: erik.c.bjorge@intel.com
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13350 6f19259b-4bc3-4df7-8a09-765794883524
0xb000 is the address normally used with QEMU.
0x400 also appears to conflict with some debug I/O ports
used by QEMU.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Erik Bjorge <erik.c.bjorge@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Bei Guan <gbtju85@gmail.com>
Reviewed-by: Bei Guan <gbtju85@gmail.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13279 6f19259b-4bc3-4df7-8a09-765794883524
If the bit is not set, then the only method ACPI defines
for setting it is to use the SMI SCI enable code path.
Since OVMF does not support SMM, we must enable the
bit during boot.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Erik Bjorge <erik.c.bjorge@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Bei Guan <gbtju85@gmail.com>
Reviewed-by: Bei Guan <gbtju85@gmail.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13278 6f19259b-4bc3-4df7-8a09-765794883524
OVMF does not support SMM. Previously the port value
was set to 0. This should be enough to disable the
SMM ACPI Enable/Disable code paths, but to be
consistent we'll set these fields to 0 as well.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Erik Bjorge <erik.c.bjorge@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Bei Guan <gbtju85@gmail.com>
Reviewed-by: Bei Guan <gbtju85@gmail.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13277 6f19259b-4bc3-4df7-8a09-765794883524
QEMU hard codes the GPE0 registers at 0xafe0.
Previously the code assumed that the GPE0 block
would move when the PM Base Address of the PIIX4
PCI device was programmed. It appears QEMU does not
emulate this behaviour of the PIIX4 PCI device.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Erik Bjorge <erik.c.bjorge@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Bei Guan <gbtju85@gmail.com>
Reviewed-by: Bei Guan <gbtju85@gmail.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13276 6f19259b-4bc3-4df7-8a09-765794883524
Contributions.txt documents the contribution process for all
tianocore projects. The conents of Contributions.txt should
match in all cases.
License.txt is a per-project document showing the license terms
used by that project.
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13187 6f19259b-4bc3-4df7-8a09-765794883524
If –D SECURE_BOOT_ENABLE is specified with the build command, Secure Boot support is enabled including custom mode setup.
This allows Secure Boot to be configured through setup allowing OvmfPkgX64, OvmfPkgIa32 and OvmfPkg3264 to be a fully functional Secure Boot reference platforms.
Remove redundant library class definitions for BaseCryptLib and OpenSslLib.
Signed-off-by: Lee Rosenbaum <lee.g.rosenbaum@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Erik Bjorge <erik.c.bjorge@intel.com>
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13160 6f19259b-4bc3-4df7-8a09-765794883524
Adjust PCD settings, library mappings and driver usage
to enable secure-boot when -D SECURE_BOOT_ENABLE=TRUE
is used on the build command line.
Signed-off-by: lgrosenb
Reviewed-by: jljusten
Reviewed-by: mdkinney
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13093 6f19259b-4bc3-4df7-8a09-765794883524
When PcdSecureBootEnable is true, the authenticated variable
FV is created. Otherwise the standard FV is created.
Signed-off-by: lgrosenb
Reviewed-by: jljusten
Reviewed-by: mdkinney
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@13092 6f19259b-4bc3-4df7-8a09-765794883524
Note: The CSM16 binary must be copied into the tree at
OvmfPkg/Csm/Csm16/Csm16.bin in order to use CSM_ENABLE.
If CSM_ENABLE is set during the build, then the CSM16 binary
and the CSM support (Legacy BIOS) drivers will be added to
the build.
Signed-off-by: jljusten
Reviewed-by: geekboy15a
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12682 6f19259b-4bc3-4df7-8a09-765794883524
This library installs the legacy interrupt, region
and platform support required for CSM support
drivers.
Signed-off-by: jljusten
Reviewed-by: geekboy15a
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12681 6f19259b-4bc3-4df7-8a09-765794883524
QEMU doesn't support MTRR emulation in some cases,
and therefore the MtrrLib calls may return an error.
In that case, we should silently ignore the error.
Signed-off-by: jljusten
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12618 6f19259b-4bc3-4df7-8a09-765794883524
Locates Xen SMBIOS data and installs it using the SMBIOS
protocol.
Signed-off-by: gavinguan
Reviewed-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: jljusten
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12125 6f19259b-4bc3-4df7-8a09-765794883524
For the first instance of the library that runs, the
base is initialized to 0x400, but we access it at 0x401.
Signed-off-by: jljusten
Reviewed-by: niruiyu
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12121 6f19259b-4bc3-4df7-8a09-765794883524
* Make PlatformPei aware of Xen
* Fix assigned PIO and MMIO ranges to be compatible with Xen
* Reserve Xen HVM address range
* Publish XenInfo HOB
* Don't program PIIX4 PMBA for Xen
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: gavinguan
Signed-off-by: jljusten
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12091 6f19259b-4bc3-4df7-8a09-765794883524
XenInfo HOB is used to pass XenInfo from PEI to DXE.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: gavinguan
Reviewed-by: jljusten
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12059 6f19259b-4bc3-4df7-8a09-765794883524
If PIIX4 Power Management Base Address (PMBA) is already
programmed, then read and use it's current setting.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: gavinguan
Signed-off-by: jljusten
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@12053 6f19259b-4bc3-4df7-8a09-765794883524
When building:
-D BUILD_NEW_SHELL - Build and include UEFI shell in firmware
-D USE_NEW_SHELL - Include UEFI shell binary build in firmware
The default is to use the older EFI shell.
Signed-off-by: jljusten
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11890 6f19259b-4bc3-4df7-8a09-765794883524
1) Remove section header comment blocks that do not provide any information
2) Combine PCDs listed in multiple sections into a single section that supports multiple PCD types to reduce maintenance overhead
3) Remove ModuleTypeList comments from [Includes], [Protocols], [Ppis], and [Guids] sections that do not properly describe the module type restrictions.
4) Clean up formatting of GUID structure declarations
5) Remove ".common" from section names if they are not required.
6) Order sections consistently as [Defines], [Includes], [LibraryClasses], [Guid], [Ppis], [Protocols], [PcdsFeatureFlag], [PcdsFixedAtBuild], [PcdsPatchableInModule], [PcdsDynamic], and [PcdsDynamicEx]
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11633 6f19259b-4bc3-4df7-8a09-765794883524
In some configurations the UNIXGCC build will run out of
space when a DEBUG build is enabled. This change adjusts
the flash configuration a bit to allow the build succeed
on UNIXGCC.
The final flash image still remains 1MB in size.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11547 6f19259b-4bc3-4df7-8a09-765794883524
This driver provides a UEFI Graphics Output Protocol (GOP) driver
for the QEMU Cirrus VGA hardware. It enables 24-bit color,
and uses the standard 32-bit GOP pixel format whenever possible.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11524 6f19259b-4bc3-4df7-8a09-765794883524
When building in release mode on OVMF, the ASSERT_EFI_ERROR
macro is empty. So, to set the BootMode, in a release build,
it must be outside of ASSERT_EFI_ERROR.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11413 6f19259b-4bc3-4df7-8a09-765794883524
This library provides an interface for converting the system
variables into a binary and also restoring the system variables
from that binary.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11284 6f19259b-4bc3-4df7-8a09-765794883524
The contents of CMOS on boot can describe some aspects of
the system configuration. For example, the size of memory
available to qemu/kvm.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11264 6f19259b-4bc3-4df7-8a09-765794883524
Change from using PcdFlashNvStorageVariableBase to
PcdFlashNvStorageVariableBase64.
This will make sure the EMU Variable FVB will
function in systems with more than 4GB of memory.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11252 6f19259b-4bc3-4df7-8a09-765794883524
Add a single build.sh to replace build32.sh & build64.sh.
The script watches for various parameters:
-a: allows selecting IA32 or X64 (default)
-b: allows selecting RELEASE or DEBUG (default)
-t: allows selecting the toolchain
When running qemu, the script doesn't always add -hda now.
If the user provides a disk parameter (for example, -fda, -hda
or -cdrom), then -hda will not be added to the qemu command line.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11238 6f19259b-4bc3-4df7-8a09-765794883524
When OVMF is run with kvm and grub2 (efi), an exception
occurs when mmx/sse registers are accessed.
As a work around, this change eliminates firmware usage
of these register types.
First, only the BaseMemoryLib implementation
MdePkg/Library/BaseMemoryLibRepStr/BaseMemoryLibRepStr.inf
is used.
Second, the GCC compiler is passes the additional
'-mno-mmx -mno-sse' parameters.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11218 6f19259b-4bc3-4df7-8a09-765794883524
These scripts are similar to those found under DuetPkg & UnixPkg.
The scripts simplify building and running OVMF under systems that
have the bash shell available.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@11215 6f19259b-4bc3-4df7-8a09-765794883524
This call can cause a reset, and is most critical for ACPI S3/S4
resume situations. OVMF does not support S3/S4.
OVMF does not have true non-volatile variable support, so
this call could cause a continuous reset situation in certain
scenarios. (The BdsLibSaveMemoryTypeInformation may set an
non-volatile variable, and then reset with the assumption that
the variable will still exist during the next boot.)
Additionally, some version of QEMU appear to hang when the
port 64 reset is initiated.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@10927 6f19259b-4bc3-4df7-8a09-765794883524
1) Update README describing the QEMU version required for e1000, where to download the UEFI drivers for e1000, and how to enable network drivers in the platform firmware
2) Update DSC/FDF files NETWORK_ENABLE switch to enable e1000 and network driver support
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@10697 6f19259b-4bc3-4df7-8a09-765794883524
Remove duplicate FFS file GUID that would cause incremental builds to fail.
Final output file is OVMF.FD and that is what should be used as bios.bin when running QEMU.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@10605 6f19259b-4bc3-4df7-8a09-765794883524
This protocol is similar to the standard UEFI BlockIo protocol,
except it has no function calls and simply defines a base address
in memory where reads & writes for the block device should occur.
One planned usage is to fill a memory region with a small disk
image, and allow it to be used as a normal disk by the
standard drivers.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@10295 6f19259b-4bc3-4df7-8a09-765794883524
gEfiEdkModulePkgTokenSpaceGuid.PcdDxePcdDatabaseTraverseEnabled does not
exist. Remove references to it in .dsc files and within the comments of
the DXE PCD driver.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@10092 6f19259b-4bc3-4df7-8a09-765794883524
In some environments, the accessed bit should be set to allow the
global descriptor table (GDT) to reside in unmodifiable flash
memory.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9675 6f19259b-4bc3-4df7-8a09-765794883524
* Only SEC is uncompressed now
* The MAIN FV with PEI & DXE can easily shrink and grow as needed
* The final output will now be OVMF.Fv rather than OVMF.fd
* The final output size will be a multiple of 64kb
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9672 6f19259b-4bc3-4df7-8a09-765794883524
Previously the interface to the SEC module was:
ESI/RSI - SEC Core entry point
EDI/RDI - PEI Core entry point
EBP/RBP - Start of BFV
Now it is:
RAX/EAX Initial value of the EAX register
(BIST: Built-in Self Test)
DI 'BP': boot-strap processor, or
'AP': application processor
RBP/EBP Address of Boot Firmware Volume (BFV)
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9572 6f19259b-4bc3-4df7-8a09-765794883524
Previously it was:
ESI/RSI - SEC Core entry point
EDI/RDI - PEI Core entry point
EBP/RBP - Start of BFV
Now it is:
RAX/EAX Initial value of the EAX register
(BIST: Built-in Self Test)
DI 'BP': boot-strap processor, or
'AP': application processor
RBP/EBP Address of Boot Firmware Volume (BFV)
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9571 6f19259b-4bc3-4df7-8a09-765794883524
a. Update PciBusDxe module, and move it from IntelFrameworkModulePkg to MdeModulePkg
b. Move IncompatiblePciDeviceSupportDxe module from IntelFrameworkModulePkg to MdeModulePkg
c. Update the related consumes in inf/dsc/fdf
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9350 6f19259b-4bc3-4df7-8a09-765794883524
Align the PE32/32+ images in the ROM for XIP (execute in place) images
to function properly following the change in r9327. Also, convert
pre-memory PEIM's to use the TE image format and strip-relocation
data from image. This saves a little space, and provides a sample
usage of TE images.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9332 6f19259b-4bc3-4df7-8a09-765794883524
Previously the code would expect that the PE32 image was in the
first section of the FFS file. This might not be the case if the
PE32 section is forced to be aligned.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9331 6f19259b-4bc3-4df7-8a09-765794883524
Note:
* This only works before ExitBootServices
* For OVMF, variables are only preserved on the disk if there
is a hard disk connected which has a writeable FAT file system.
The Ovmf/Library/EmuVariableFvbLib library will look for the
gUefiOvmfPkgTokenSpaceGuid.PcdEmuVariableEvent PCD to be set to
a non-zero value. If set, it is treated as an event handle, and
each write to the EmuVariableFvb will cause the event to be
signaled.
In this change, the OVMF platform BDS library sets up this event,
and sets the PCD so that after each write to the EMU Variable FVB,
the non-volatile variables will be saved out to the file system.
The end result is that NV variables that are written prior to the
ExitBootServices call should be preserved by storing them on the
disk.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9318 6f19259b-4bc3-4df7-8a09-765794883524
OVMF utilizes EmuVariableFvbRuntimeDxe to provide an emulated
variable firmware volume block device for non-volatile variables.
This allows the VariableRuntimeDxe and FaultTolerantWriteDxe
to function without a real non-volatile backing store.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9317 6f19259b-4bc3-4df7-8a09-765794883524
This driver implements a firmware volume block protocol instance
which is stored in system memory.
The MdeModulePkg/Universal/Variable/RuntimeDxe and
MdeModulePkg/Universal/FaultTolerantWriteDxe drivers make use of
this FVB instance to provide variable services.
This driver links to a PlatformFvb library to allow for
platform specific processing to take place when data is written
to the FVB.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9315 6f19259b-4bc3-4df7-8a09-765794883524
This library provides an interface where variables can be saved and restored
using a file in a file system accessible to the firmware. It is expected
that a platform BDS library will use this library. The platform BDS
implementation can decide which devices to connect and then to attempt to use
for saving and restoring NV variables.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9272 6f19259b-4bc3-4df7-8a09-765794883524
Make use of EMU Variable driver's PcdEmuVariableNvStoreReserved to allow
NV variables to persist a VM system reset. The contents of the NV variables
will still be lost when the VM is shut down, but they appear to persist
when the efi shell reset command is run. (Tested with QEMU 0.10.0.)
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@9241 6f19259b-4bc3-4df7-8a09-765794883524
QEMU will automatically fill the video BIOS image into memory at the
legacy video BIOS memory location (0xc0000). This code will look
there for a EFI option rom image, and load it if it found. This
allows the video option ROM to be separated out from the main system
firmware image.
QEMU does not appear to emulate the PCI rom expansion method
for making the video BIOS available to the system.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@8942 6f19259b-4bc3-4df7-8a09-765794883524
It is not proper for a library implementation to assume the names of function in a parent module.
Instead, they must be designed as the pointers to these two BdsDxe functions and passed in.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@8931 6f19259b-4bc3-4df7-8a09-765794883524
Move many libraries to Libraries.common section.
Add basic UEFI_APPLICATION libraries to allow applications
to be easily added to OVMF builds.
git-svn-id: https://edk2.svn.sourceforge.net/svnroot/edk2/trunk/edk2@8688 6f19259b-4bc3-4df7-8a09-765794883524
jljusten
ydong10
niruiyu
leegrosenbaum
hhtian
lgao4
vanjeff
rsun3
lzeng14
li-elvin
xdu2
gikidy
mdkinney
klu2
geekboy15a
xli24
eric_tian
qhuang8
davidhuang
jchen20