The implementation of this new behavior aligns with the guidelines
outlined in the Intel SDM.
Following a power-up or RESET of an MP system, system hardware
dynamically selects one of the processors on the system bus as the BSP.
The remaining processors are designated as APs. The APs complete a
minimal self-configuration, then wait for a startup signal (a SIPI
message) from the BSP processor.
Additionally, the MP protocol is executed only after
a power-up or RESET. If the MP protocol has completed and a
BSP is chosen, subsequent INITs (either to a specific processor or
system wide) do not cause the MP protocol to be repeated. Instead, each
logical processor examines its BSP flag (in the IA32_APIC_BASE MSR) to
determine whether it should execute the BIOS boot-strap code (if it is
the BSP) or enter a wait-for-SIPI state (if it is an AP).
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Add PcdFirstTimeWakeUpAPsBySipi to check if it is in the OVMF environment
and necessary to wake up APs by INIT-SIPI-SIPI.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
The purpose is to fix an issue where an exception occurs at the start
of the DXE phase by applying the following patch series on INTEL-based
systems.
UefiCpuPkg: Refactor the logic for placing APs in HltLoop.
UefiCpuPkg: Refactor the logic for placing APs in Mwait/Runloop.
UefiCpuPkg: Create MpHandOff.
UefiCpuPkg: ApWakeupFunction directly use CpuMpData.
UefiCpuPkg: Eliminate the second INIT-SIPI-SIPI sequence.
This series of patches makes changes to the way the APs are
initialized and woken up. It removes the 2nd time INIT-SIPI-SIPI and
introduces a special startup signal to wake up APs. These patches also
create a new HOB identified by the mMpHandOffGuid, which stores only the
minimum information required from the PEI phase to the DXE phase.
As a result, the original HOB (mCpuInitMpLibHobGuid) is now used only
as a global variable in the PEI phase and is no longer necessary in the
DXE phase for INTEL-based systems. The AMD SEV-ES related code
still relies on the OldCpuMpData in the DXE phase.
This patch decouple the SEV-ES functionality of assigning CpuMpData to
OldCpuMpData->NewCpuMpData from the Intel logic.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
When both the PEI and DXE phases operate in the same execution
mode(32-bit/64-bit), the BSP send a special start-up signal during
the DXE phase to awaken the Application APs.
To eliminate the need for the INIT-SIPI-SIPI sequence at the beginning
of the DXE phase, the BSP call the SwitchApContext function to trigger
the special start-up signal. By writing the specified
StartupSignalValue to the designated StartupSignalAddress, the BSP
wakes up the APs from mwait mode. Once the APs receive the
MP_HAND_OFF_SIGNAL value, they are awakened and proceed to execute the
SwitchContextPerAp procedure. They enter another while loop,
transitioning their context from the PEI phase to the DXE phase.
The original state transitions for an AP during the procedure are as
follows:
Idle ----> Ready ----> Busy ----> Idle
[BSP] [AP] [AP]
Instead of init-sipi-sipi sequence, we make use of a
start-up signal to awaken the APs and transfer their context from
PEI to DXE. Consequently, APs, rather than the BSP, to set their state
to CpuStateReady.
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
In the original design, once the APs finished executing their assembly
code and switched to executing C code, they would enter a continuous
loop within a function. In this function, they would collect CpuMpData
using the MP_CPU_EXCHANGE_INFO mechanism. However, in the updated
approach, CpuMpData can now be passed directly to the ApWakeUpFunction,
bypassing the need for MP_CPU_EXCHANGE_INFO. This modification is made
in preparation for eliminating the requirement of a second
INIT-SIPI-SIPI sequence in the DXE phase.
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Initially, the purpose of the Hob was twofold: it served as a way to
transfer information from PEI to DXE. However, during the DXE phase,
only a few fields from the CPU_MP_DATA which collected in PEI phase were
needed. A new Hob was specifically created to transfer information
to the DXE phase. This new Hob contained only the essential fields
required for reuse in DXE. For instance, instead of directly including
the BspNumber in MpHandOff, the DXE phase introduced the use of
GetBspNumber() to collect the BspNumber from ApicID and CpuCount.
The SaveCpuMpData() function was updated to construct the MP_HAND_OFF
Hob. Additionally, the function introduced the MP_HAND_OFF_SIGNAL,
which solely served the purpose of awakening the APs
and transitioning their context from PEI to DXE. The
WaitLoopExecutionMode field indicated whether the bit mode of PEI
matched that of DXE. Both of them were filled only if the ApLoopMode
was not ApInHltLoop. In the case of ApInHltLoop, it remained necessary
to wake up the APs using the init-sipi-sipi sequence. This improvement
still allow INIT-SIPI-SIPI even APs are wait in Run/Mwait loop mode.
The function GetMpHandOffHob() was added to facilitate access to the
collected MpHandOff in the DXE phase. The CpuMpData in the DXE phase
was updated by gathering information from MpHandOff. Since MpHandOff
replaced the usage of OldCpuMpData and contained essential information
from the PEI phase to the DXE phase. AmdSevUpdateCpuMpData was included
to maintain the original implementation of AmdSev, ensuring that
OldCpuMpData->NewCpuMpData pointed to CpuMpData.
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Refactor the logic for placing APs in
Mwait/Runloop into a separate function.
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Refactor the logic for placing APs in HltLoop into a separate function.
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
__FUNCTION__ is a pre-standard extension that gcc and Visual C++ among
others support, while __func__ was standardized in C99.
Since it's more standard, replace __FUNCTION__ with __func__ throughout
UefiCpuPkg.
Signed-off-by: Rebecca Cran <rebecca@bsdio.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4353
Due to AMD erratum #1467, an SEV-SNP VMSA should not be 2MB aligned. To
work around this issue, allocate two pages instead of one. Because of the
way that page allocation is implemented, always try to use the second
page. If the second page is not 2MB aligned, free the first page and use
the second page. If the second page is 2MB aligned, free the second page
and use the first page. Freeing in this way reduces holes in the memory
map.
Fixes: 06544455d0 ("UefiCpuPkg/MpInitLib: Use SEV-SNP AP Creation ...")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Ray Ni <ray.ni@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=4353
When parking the APs on exiting from UEFI, a new page allocation is made.
This allocation, however, does not end up being marked reserved in the
memory map supplied to the OS. To avoid this, re-use the VMSA by clearing
the VMSA RMP flag, updating the page contents and re-setting the VMSA RMP
flag.
Fixes: 06544455d0 ("UefiCpuPkg/MpInitLib: Use SEV-SNP AP Creation ...")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Ray Ni <ray.ni@intel.com>
Add OUTPUT IsModified parameter in PageTableMap() to indicate
if page table has been modified. With this parameter, caller
can know if need to call FlushTlb when the page table is in CR3.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
In function CreatePageTable(), add code to initialize MapMask to
MAX_UINT64. When creating new page table or map non-present range
to present, all attributes should be provided.
Signed-off-by: Dun Tan <dun.tan@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
For the case CPU logic index is 0, RSP points to the very top of all AP
stacks. That address is not mapped in page table.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Signed-off-by: Ted Kuo <ted.kuo@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Because UefiCpuPkg/UefiCpuLib is merged to MdePkg/CpuLib, remove the
dependency of UefiCpuLib.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Yu Pu <yu.pu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Rename AsmRelocateApLoopStart to AsmRelocateApLoopStartAmdSev
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Add the 'AsmRelocateApLoopStartGeneric' for X64 processors except 64-bit
AMD processors with SEV-ES.
Remove the unused arguments of AsmRelocateApLoopStartGeneric, updated
the stack offset.
Create PageTable for the allocated reserved memory.
Only keep 4GB limitation of memory allocation for the case APs still
need to be transferred to 32-bit mode before OS.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Add the union RELOCATE_AP_LOOP_ENTRY, split the path in RelocateApLoop
into two:
1. 64-bit AMD processors with SEV-ES
2. Intel processors (32-bit or 64-bit), 32-bit AMD processors, or
64-bit AMD processors without SEV-ES.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Check if AP_SAFE_STACK_SIZE is aligned with CPU_STACK_ALIGNMENT
during build time.
No functional or structural changes.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
This reverts commit 73ccde8f6d since it
results in a hang of the IA32 processor and needs further clean-up.
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=4234
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
During the finalization of Mp initialization before booting into the OS,
depending on whether Mwait is supported or not, AsmRelocateApLoop
places Aps in MWAIT-loop or HLT-loop.
Since paging is necessary for long mode, the original implementation of
moving APs to 32-bit was to disable paging to ensure that the booting
does not crash.
The current modification creates a page table in reserved memory,
avoiding switching modes and reclaiming memory by OS. This modification
is only for 64 bit mode.
More specifically, we keep the AMD logic as the original code flow,
extract and update the Intel-related code, where the APs would stay
in 64-bit, and run in a Mwait or Hlt loop until the OS wake them up.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
AsmRelocateApLoop is replicated for future Intel Logic Extraction,
further brings AP into 64-bit, and enables paging.
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4123
APIs which are defined in CcExitLib.h are added with the CcExit prefix.
This is to make the APIs' name more meaningful.
This change impacts OvmfPkg/UefiCpuPkg.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=4123
VmgExitLib once was designed to provide interfaces to support #VC handler
and issue VMGEXIT instruction. After TDVF (enable TDX feature in OVMF) is
introduced, this library is updated to support #VE as well. Now the name
of VmgExitLib cannot reflect what the lib does.
This patch renames VmgExitLib to CcExitLib (Cc means Confidential
Computing). This is a simple renaming and there is no logic changes.
After renaming all the VmgExitLib related codes are updated with
CcExitLib. These changes are in OvmfPkg/UefiCpuPkg/UefiPayloadPkg.
Cc: Guo Dong <guo.dong@intel.com>
Cc: Sean Rhodes <sean@starlabs.systems>
Cc: James Lu <james.lu@intel.com>
Cc: Gua Guo <gua.guo@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: James Lu <james.lu@intel.com>
Reviewed-by: Gua Guo <gua.guo@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
To remove the dependency of CPU register, 4/8 byte at the top of the
stack is occupied for CpuMpData. BIST information is also taken care
here. This modification is only for PEI phase, since in DXE phase
CpuMpData is accessed via global variable.
Signed-off-by: Yuanhao Xie <yuanhao.xie@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
When switch bsp, old bsp and new bsp put CR0/CR4 into stack, and put IDT
and GDT register into a structure. After they exchange their stack, they
restore these registers. This logic is now implemented by assembly code.
This patch aims to reuse (Save/Restore)VolatileRegisters function to
replace such assembly code for better code readability.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
Currently, when waking up AP, IDT table of AP will be set in 16 bit code,
and assume the IDT table base is 32 bit. However, the IDT table is created
by BSP. Issue will happen if the BSP allocates memory above 4G for BSP's
IDT table. Moreover, even the IDT table location is below 4G, the handler
function inside the IDT table is 64 bit, and it won't take effect until
CPU transfers to 64 bit long mode. There is no benefit to set IDT table in
such an early phase.
To avoid such issue, this patch moves the LIDT instruction into 64 bit
code.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Zhiguang Liu <zhiguang.liu@intel.com>
The AP vector consists of 2 parts:
1. the initial 16-bit code that should be under 1MB and page aligned.
2. the 32-bit/64-bit code that can be anywhere in the memory with any
alignment.
The need of part #2 is because the memory under 1MB is temporary
"stolen" for use and will "give" back after all AP wake up. The range
of memory is not marked as code page in page table. CPU may trigger
exception as soon as NX is enabled.
The part #2 memory allocation can be done in the MpInitLibInitialize.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Today's implementation allocates below 1MB memory for the 16bit, 32bit
and 64bit code.
But it's not necessary since now the 32bit and 64bit code run at high
memory no matter in PEI and DXE phase.
The patch simplifies the logic to remove the code that handles the
case when WakeupBufferHigh is 0.
It also reduce the memory foot print under 1MB by allocating
memory for 16bit code only.
MP_CPU_EXCHANGE_INFO is still under 1MB which is immediate
after the 16bit code.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
The patch does several simplifications:
1. Treat SwitchToRealProc as part of RendezvousFunnelProc.
So the common logic in MpLib.c doesn't need to be aware of
SwitchToRealProc.
As a result, SwitchToRealSize/Offset are removed from
MP_ASSEMBLY_ADDRESS_MAP.
2. Move SwitchToRealProc to AmdSev.nasm.
All other assembly code in AmdSev.nasm is called through
OneTimeCall.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Michael Roth <michael.roth@amd.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Min Xu <min.m.xu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
global in NASM file is used for symbols that are
referenced in C files.
Remove unneeded global keyword in NASM file.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Today's implementation assumes PEI phase runs at 32bit so
the execution-disable feature is not applicable.
It's not always TRUE.
The patch allocates 32bit&64bit code buffer for PEI phase as well.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3918
This reverts commit 88da06ca76.
This commit triggers the ASSERT in Non-Td guest.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
RFC: https://bugzilla.tianocore.org/show_bug.cgi?id=3429
In TDVF BSP and APs are simplified. BSP is the vCPU-0, while the others
are treated as APs.
So MP intialization is rather simple. ApWorker is not supported, BSP is
always the working processor, while the APs are just in a
wait-for-precedure state.
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Signed-off-by: Min Xu <min.m.xu@intel.com>
To keep the declaration same with definition, remove the last optional
in declaration of WakeUpAP.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Wenyi Xie <xiewenyi2@huawei.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3790
Replace Opcode with the corresponding instructions.
The code changes have been verified with CompareBuild.py tool, which
can be used to compare the results of two different EDK II builds to
determine if they generate the same binaries.
(tool link: https://github.com/mdkinney/edk2/tree/sandbox/CompareBuild)
Signed-off-by: Jason Lou <yun.lou@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3275
Use the SEV-SNP AP Creation NAE event to create and launch APs under
SEV-SNP. This capability will be advertised in the SEV Hypervisor
Feature Support PCD (PcdSevEsHypervisorFeatures).
Cc: Michael Roth <michael.roth@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Min Xu <min.m.xu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Ray Ni <ray.ni@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
During AP bringup, just after switching to long mode, APs will do some
cpuid calls to verify that the extended topology leaf (0xB) is available
so they can fetch their x2 APIC IDs from it. In the case of SEV-ES,
these cpuid instructions must be handled by direct use of the GHCB MSR
protocol to fetch the values from the hypervisor, since a #VC handler
is not yet available due to the AP's stack not being set up yet.
For SEV-SNP, rather than relying on the GHCB MSR protocol, it is
expected that these values would be obtained from the SEV-SNP CPUID
table instead. The actual x2 APIC ID (and 8-bit APIC IDs) would still
be fetched from hypervisor using the GHCB MSR protocol however, so
introducing support for the SEV-SNP CPUID table in that part of the AP
bring-up code would only be to handle the checks/validation of the
extended topology leaf.
Rather than introducing all the added complexity needed to handle these
checks via the CPUID table, instead let the BSP do the check in advance,
since it can make use of the #VC handler to avoid the need to scan the
SNP CPUID table directly, and add a flag in ExchangeInfo to communicate
the result of this check to APs.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Min Xu <min.m.xu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Ray Ni <ray.ni@intel.com>
Suggested-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3275
An SEV-SNP guest requires that the physical address of the GHCB must
be registered with the hypervisor before using it. See the GHCB
specification section 2.3.2 for more details.
Cc: Michael Roth <michael.roth@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Min Xu <min.m.xu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Ray Ni <ray.ni@Intel.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3275
Previous commit introduced a generic confidential computing PCD that can
determine whether AMD SEV-ES is enabled. Update the MpInitLib to drop the
PcdSevEsIsEnabled in favor of PcdConfidentialComputingAttr.
Cc: Michael Roth <michael.roth@amd.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Min Xu <min.m.xu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Ray Ni <ray.ni@intel.com>
Suggested-by: Jiewen Yao <jiewen.yao@intel.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3275
Move all the SEV specific function in AmdSev.c.
No functional change intended.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Michael Roth <michael.roth@amd.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Min Xu <min.m.xu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Suggested-by: Jiewen Yao <Jiewen.yao@intel.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3737
Apply uncrustify changes to .c/.h files in the UefiCpuPkg package
Cc: Andrew Fish <afish@apple.com>
Cc: Leif Lindholm <leif@nuviainc.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Signed-off-by: Michael Kubacki <michael.kubacki@microsoft.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3767
Update use of DEBUG_CODE(Expression) if Expression is a complex code
block with if/while/for/case statements that use {}.
Cc: Andrew Fish <afish@apple.com>
Cc: Leif Lindholm <leif@nuviainc.com>
Cc: Michael Kubacki <michael.kubacki@microsoft.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3760
Update all use of ', OPTIONAL' to ' OPTIONAL,' for function params.
Cc: Andrew Fish <afish@apple.com>
Cc: Leif Lindholm <leif@nuviainc.com>
Cc: Michael Kubacki <michael.kubacki@microsoft.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3324
The SEV-ES stacks currently share a page with the reset code and data.
Separate the SEV-ES stacks from the reset vector code and data to avoid
possible stack overflows from overwriting the code and/or data.
When SEV-ES is enabled, invoke the GetWakeupBuffer() routine a second time
to allocate a new area, below the reset vector and data.
Both the PEI and DXE versions of GetWakeupBuffer() are changed so that
when PcdSevEsIsEnabled is true, they will track the previous reset buffer
allocation in order to ensure that the new buffer allocation is below the
previous allocation. When PcdSevEsIsEnabled is false, the original logic
is followed.
Fixes: 7b7508ad78
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Marvin Häuser <mhaeuser@posteo.de>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <3cae2ac836884b131725866264e0a0e1897052de.1621024125.git.thomas.lendacky@amd.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3385
A VS2012 build fails with a cast conversion warning when the SEV-ES work
area PCD is cast as a pointer to the SEV_ES_AP_JMP_FAR type.
When casting from a PCD value to a pointer, the cast should first be done
to a UINTN and then to the pointer. Update the code to perform a cast to
a UINTN before casting to a pointer to the SEV_ES_AP_JMP_FAR type.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Fixes: 7b7508ad78
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <c89bc819856d448360430c32cb3833a9667f987b.1620656694.git.thomas.lendacky@amd.com>
Reviewed-by: Liming Gao <gaoliming@byosoft.com.cn>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
YuanhaoXie
Rebecca Cran
Lendacky, Thomas via groups.io
Dun Tan
Yu Pu
Min M Xu
Liu, Zhiguang
Ray Ni
wenyi,xie via groups.io
Jason
Tom Lendacky
Michael Roth
Brijesh Singh
Michael Kubacki
Michael D Kinney