REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1934
0x0 MicrocodeBegin MicrocodeEntry MicrocodeEnd 0xffffffff
|--------------|---------------|---------------|---------------|
valid TotalSize
TotalSize is only valid between 0 and (MicrocodeEnd - MicrocodeEntry).
So add '(UINTN)MicrocodeEntryPoint > (MAX_ADDRESS - TotalSize)' before
'((UINTN)MicrocodeEntryPoint + TotalSize) > MicrocodeEnd' to make sure
((UINTN)MicrocodeEntryPoint + TotalSize) wouldn't overflow.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Zhichao Gao <zhichao.gao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
The patch fixes the bug that the memory under 1MB is modified by
firmware in S3 boot.
Root cause is a racing condition in MpInitLib:
1. BSP: WakeUpByInitSipiSipi is set by NotifyOnS3SmmInitDonePpi()
2. BSP: WakeUpAP() wakes all APs to run certain procedure.
2.1. AllocateResetVector() uses <1MB memory for wake up vector.
2.1. FillExchangeInfoData() resets NumApsExecuting to 0.
2.2. WaitApWakeup() waits AP to clear WAKEUP_AP_SIGNAL.
3. AP: ApWakeupFunction() clears WAKEUP_AP_SIGNAL to inform BSP.
5. BSP: FreeResetVector() restores the <1MB memory
4. AP: ApWakeupFunction() calls the certain procedure.
4.1. NumApsExecuting is decreased.
#4.1 happens after the 1MB memory is restored so the result is
memory below 1MB is changed by #4.1
It happens only when the AP executes procedure a bit longer.
AP returns back to ApWakeupFunction() from procedure after
BSP restores the <1MB memory.
Since NumApsExecuting is only used when InitFlag == ApInitConfig
for counting the processor count.
The patch moves the NumApsExecuting decrease to the path when
InitFlag == ApInitConfig.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Nandagopal Sathyanarayanan <nandagopal.sathyanarayanan@intel.com>
NumApsExecuting is only used when InitFlag == ApInitConfig for
counting the processor count.
The patch changes Ia32 version of waking up vector assembly code
to align to x64 version of waking up vector assembly code.
After the change both versions of waking up vector increase
NumApsExecuting when InitFlag == ApInitConfig.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1810
This patch covers two problems.
1. Current code gets CPUID_THERMAL_POWER_MANAGEMENT in
ClockModulationInitialize() and uses its ECMD bit for all processors.
But ClockModulationInitialize() is only executed by BSP, that means
the bit is just for BSP.
It may have no functionality issue as all processors may have same
bit value in a great possibility. But for good practice, the code
should get CPUID_THERMAL_POWER_MANAGEMENT in ClockModulationSupport
(executed by all processors), and then use them in
ClockModulationInitialize() for all processors.
We can see that Aesni.c (and others) have used this good practice.
2. Current code uses 3 CPU_REGISTER_TABLE_WRITE_FIELD for
MSR_IA32_CLOCK_MODULATION in ClockModulationInitialize(), they can
be reduced to 1 CPU_REGISTER_TABLE_WRITE64 by getting
MSR_IA32_CLOCK_MODULATION for all processors in
ClockModulationSupport() and then update fields for register table
write in ClockModulationInitialize().
We may argue that there may be more times of MSR_IA32_CLOCK_MODULATION
getting. But actually the times of MSR_IA32_CLOCK_MODULATION getting
could be also reduced.
The reason is in ProgramProcessorRegister() of CpuFeaturesInitialize.c,
AsmMsrBitFieldWrite64 (AsmReadMsr64 + AsmWriteMsr64) will be used for
CPU_REGISTER_TABLE_WRITE_FIELD, and AsmWriteMsr64 will be used for
CPU_REGISTER_TABLE_WRITE64.
The times of MSR accessing could be reduced with this patch.
Without the patch:
3 CPU_REGISTER_TABLE_WRITE_FIELD (in ClockModulationInitialize)
==> 3 AsmMsrBitFieldWrite64
==> 3 AsmReadMsr64 + 3 AsmWriteMsr64
With the patch:
1 AsmReadMsr64 (in ClockModulationSupport) +
1 CPU_REGISTER_TABLE_WRITE64 (in ClockModulationInitialize)
==> 1 AsmWriteMsr64
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1829
There will be ASSERT if LMCE is supported as below.
DXE_ASSERT!: [CpuFeaturesDxe]
XXX\UefiCpuPkg\Library\CpuCommonFeaturesLib\MachineCheck.c (342):
ConfigData != ((void *) 0)
The code should get Config Data and FeatureControlGetConfigData
could be used.
This issue is there since the code was added at the commit below.
Revision: 3d6275c113
Date: 2017/8/4 8:46:41
UefiCpuPkg CpuCommonFeaturesLib: Enable LMCE feature.
The commits below are also related to move the code.
Revision: 0233871442
Date: 2017/9/1 10:12:38
UefiCpuPkg/Lmce.c Remove useless file.
Revision: 306a5bcc6b
Date: 2017/8/17 11:40:38
UefiCpuPkg/CpuCommonFeaturesLib: Merge machine check code to same file.
So, the code may not be tested at all on a platform
that supports LMCE.
BTW: A typo in LmceInitialize is also fixed.
The typo is introduced by the commit below.
Revision: d28daaddb3
Date: 2018/10/17 9:24:05
UefiCpuPkg/CpuCommonFeaturesLib: Register MSR base on scope Info.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1808
In current code, the values of TopaEntryPtr->Uint64 for TopaTable
and the values of OutputBaseReg.Uint64 and OutputMaskPtrsReg.Uint64
to register table write for RTIT_OUTPUT_BASE and RTIT_OUTPUT_MASK_PTRS
are not been initialized in whole. For example, the reserved bits in
OutputBaseReg.Uint64 are random that will cause GP fault like below
when SetProcessorRegister (in CpuFeaturesInitialize.c) sets register
based on register table.
!!!! X64 Exception Type - 0D(#GP - General Protection)
CPU Apic ID - 00000000 !!!!
ExceptionData - 0000000000000000
RIP -0000000064D69576, CS -0000000000000038, RFLAGS -0000000000010246
RAX -000000006B9F1001, RCX -0000000000000560, RDX -0000000000000000
RBX -0000000064EECA18, RSP -000000006CB82BA0, RBP -0000000000000008
RSI -0000000080000000, RDI -0000000000000011
R8 -000000006B9493D0, R9 -0000000000000010, R10 -00000000000000FF
R11 -000000006CB82A50, R12 -0000000064D70F50, R13 -0000000066547050
R14 -0000000064E3E198, R15 -0000000000000000
DS -0000000000000030, ES -0000000000000030, FS -0000000000000030
GS -0000000000000030, SS -0000000000000030
CR0 -0000000080010013, CR2 -0000000000000000, CR3 -000000006C601000
CR4 -0000000000000628, CR8 -0000000000000000
DR0 -0000000000000000, DR1 -0000000000000000, DR2 -0000000000000000
DR3 -0000000000000000, DR6 -00000000FFFF0FF0, DR7 -0000000000000400
GDTR -000000006B8CCF18 0000000000000047, LDTR -0000000000000000
IDTR -000000006687E018 0000000000000FFF, TR -0000000000000000
FXSAVE_STATE -000000006CB82800
And current code gets MSR_IA32_RTIT_CTL, MSR_IA32_RTIT_OUTPUT_BASE and
MSR_IA32_RTIT_OUTPUT_MASK_PTRS in ProcTraceInitialize() and uses their
values for all processors. But ProcTraceInitialize() is only executed
by BSP, that means the values just for BSP. For good practice, the code
should get MSR_IA32_RTIT_CTL, MSR_IA32_RTIT_OUTPUT_BASE and
MSR_IA32_RTIT_OUTPUT_MASK_PTRS in ProcTraceSupport (executed by all
processors), and then use them in ProcTraceInitialize() for all
processors. This can also resolve the issue that the values of
OutputBaseReg.Uint64 and OutputMaskPtrsReg.Uint64 are not been
initialized in whole.
For TopaEntryPtr->Uint64, this patch updates code to initialize it
in whole explicitly by TopaEntryPtr->Uint64 = 0 before updating its
fields.
At the same time, this patch also eliminates the ProcTraceSupported
field in PROC_TRACE_PROCESSOR_DATA and the TopaMemArrayCount field in
PROC_TRACE_DATA.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1809
Current code disables TraceEn at the end of ProcTraceInitialize(),
then there will be much memory allocated even when ProcTrace feature
is disabled.
This patch updates code to disable TraceEn and return at the beginning
of ProcTraceInitialize() when when ProcTrace feature is disabled.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1679
The checking to CpuInfo->CpuIdVersionInfoEcx.Bits.AESNI is enough,
the checking to CPU generation could be removed, then the code
could be reused by more platforms.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
These files have \r\n line endings, but a few lines use \r\r\n which
is not a valid line ending. These lines were causing problems for git
and other tools.
Signed-off-by: Joe Richey <joerichey@google.com>
Review-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Add a new instance of the MpInitLib that is designed for
uniprocessor platforms that require the use of modules
that depend on the MP_SERVICES_PROTOCOL for dispatch
or to retrieve information about the boot processor.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
GetProcessorLocation2ByApicId() extracts the
package/die/tile/module/core/thread ID from the initial APIC ID.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Zhiqiang Qin <zhiqiang.qin@intel.com>
Cc: Ray Ni <Ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
PcdCpuFeaturesSupport used to specify the platform policy about
what CPU features this platform supports. This PCD will be used
in IsCpuFeatureSupported only.
Now RegisterCpuFeaturesLib use this PCD as an template to Get the
pcd size. Update the code logic to replace it with
PcdCpuFeaturesSetting.
BZ:https://bugzilla.tianocore.org/show_bug.cgi?id=1375
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
PcdCpuFeaturesUserConfiguration.
Merge PcdCpuFeaturesUserConfiguration into PcdCpuFeaturesSetting.
Use PcdCpuFeaturesSetting as input for the user input feature setting
Use PcdCpuFeaturesSetting as output for the final CPU feature setting
BZ:https://bugzilla.tianocore.org/show_bug.cgi?id=1375
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
V2 changes:
Update the commit message and comments in the code.
When waking vector buffer allocated by CpuDxe is tested by MemTest86
in MP mode, an error is reported because the same range of memory is
modified by both CpuDxe driver and MemTest86.
The waking vector buffer is not expected to be tested by MemTest86 if
it is allocated out because MemTest86 only tests free memory. But
current CpuDxe driver "borrows" buffer instead of allocate buffer for
waking vector buffer (through allocate & free to get the buffer
pointer, backup the buffer data before using it and restore it after
using). With this implementation, if the buffer borrowed is not used
by any other drivers, MemTest86 tool will treat it as free memory
and test it.
In order to fix the above issue, CpuDxe changes to allocate the
buffer below 1M instead of borrowing it. But directly allocating
memory below 1MB causes LegacyBios driver fails to start. LegacyBios
driver allocates memory range from
"0xA0000 - PcdEbdaReservedMemorySize" to 0xA0000 as Ebda Reserved
Memory. The minimum value for "0xA0000 - PcdEbdaReservedMemorySize"
is 0x88000. If LegacyBios driver allocate this range failed, it
asserts.
LegacyBios also reserves range from 0x60000 to
"0x60000 + PcdOpromReservedMemorySize", it will be used as Oprom
Reserve Memory. The maximum value for "0x60000 +
PcdOpromReservedMemorySize" is 0x88000. LegacyBios driver tries to
allocate these range page(4K size) by page. It just reports warning
message if some pages are already allocated by others.
Base on above investigation, one page in range 0x60000 ~ 0x88000 can
be used as the waking vector buffer.
LegacyBios driver only reports warning when page allocation in range
[0x60000, 0x88000) fails. This library is consumed by CpuDxe driver
to produce CPU Arch protocol. LagacyBios driver depends on CPU Arch
protocol which guarantees below allocation runs earlier than
LegacyBios driver.
Cc: Ray Ni <ray.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
.nasm file has been added for X86 arch. .S assembly code
is not required any more.
https://bugzilla.tianocore.org/show_bug.cgi?id=1594
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Shenglei Zhang <shenglei.zhang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
.nasm file has been added for X86 arch. .S assembly code
is not required any more.
https://bugzilla.tianocore.org/show_bug.cgi?id=1594
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Shenglei Zhang <shenglei.zhang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
.nasm file has been added for X86 arch. .S assembly code
is not required any more.
https://bugzilla.tianocore.org/show_bug.cgi?id=1594
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Shenglei Zhang <shenglei.zhang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1621
According to Intel SDM as below, the BIT0 should be treated as
lock bit, and BIT1 should be treated as disable(1)/enable(0) bit.
"11b: AES instructions are not available until next
RESET.
Otherwise, AES instructions are available.
If the configuration is not 01b, AES
instructions can be mis-configured if a privileged agent
unintentionally writes 11b"
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1020
Should make sure the TotalSize of Microcode is aligned with 4 bytes
before calling CalculateSum32 function.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1020
The Microcode region indicated by MicrocodePatchAddress PCD may contain
more than one Microcode entry. We should save InCompleteCheckSum32 value
for each payload. Move the logic for calculate InCompleteCheckSum32 from
the outsize of the do-while loop to the inside.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1576
The root cause of this issue is that non-stop mode of Heap Guard and
NULL Detection set TF bit (single-step) in EFLAG unconditionally in
the common handler in CpuExceptionLib.
If PcdCpuSmmStaticPageTable is FALSE, the SMM will only create page
table for memory below 4G. If SMM tries to access memory beyond 4G,
a page fault exception will be triggered and the memory to access
will be added to page table so that SMM code can continue the access.
Because of above issue, the TF bit is set after the page fault is
handled and then fall into another DEBUG exception. Since non-stop
mode of Heap Guard and NULL Detection are not enabled, no special
DEBUG exception handler is registered. The default handler just
prints exception context and go into dead loop.
Actually EFLAGS can be changed in any standard exception handler.
There's no need to do single-step setup in assembly code. So the fix
is to move the logic to C code part of page fault exception handler
so that we can fully validate the configuration and prevent TF bit
from being set unexpectedly.
Fixes: dcc026217f16b918bbaf
Test:
- Pass special test of accessing memory beyond 4G in SMM mode
- Boot to OS with Qemu emulator platform (Fedora27, Ubuntu18.04,
Windows7, Windows10)
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1521
Add information dump for Control Protection exception.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Yao Jiewen <jiewen.yao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1020
The following Microcode payload format is define in SDM spec.
Payload: |MicrocodeHeader|MicrocodeBinary|ExtendedHeader|ExtendedTable|.
When we verify the CheckSum32 with ExtendedTable, we should use the fields
of ExtendedTable to replace corresponding fields in MicrocodeHeader,
and then calculate the CheckSum32 with MicrocodeHeader+MicrocodeBinary.
This patch already verified on ICL platform.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Zhang Chao B <chao.b.zhang@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1481
Today's MtrrLib contains a bug, for example:
when the original cache setting is WB for [0xF_0000, 0xF_8000) and,
a new request to set [0xF_0000, 0xF_4000) to WP,
the cache setting for [0xF_4000, 0xF_8000) is reset to UC.
The reason is when MtrrLibSetBelow1MBMemoryAttribute() is called the
WorkingFixedSettings doesn't contain the actual MSR value stored in
hardware, but when writing the fixed MTRRs, the code logic assumes
WorkingFixedSettings contains the actual MSR value.
The new fix is to change MtrrLibSetBelow1MBMemoryAttribute() to
calculate the correct ClearMasks[] and OrMasks[], and use them
directly when writing the fixed MTRRs.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Chasel Chiu <chasel.chiu@intel.com>
In AcquireSpinLock function, it may call GetPerformanceCounter which
final calls PeiService table. This code may also been used by AP but
AP should not calls PeiService. This patch update code to avoid use
AcquireSpinLock function.
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1411
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
V3:
Define union to specify the ppi or protocol.
V2:
1. Initialize CpuFeaturesData->MpService in CpuInitDataInitialize
and make this function been called at the begin of the
initialization.
2. let all other functions use CpuFeaturesData->MpService install
of locate the protocol itself.
V1:
GetProcessorIndex function calls GetMpPpi to get the MP Ppi.
Ap will calls GetProcessorIndex function which final let AP calls
PeiService.
This patch avoid GetProcessorIndex call PeiService.
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1411
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Enhance debug message format to let them easy to read.
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1411
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=1091
Previously, when compiling NASM source files, BaseTools did not support
including files outside of the NASM source file directory. As a result, we
duplicated multiple copies of "StuffRsb.inc" files in UefiCpuPkg. Those
INC files contain the common logic to stuff the Return Stack Buffer and
are identical.
After the fix of BZ 1085:
https://bugzilla.tianocore.org/show_bug.cgi?id=1085
The above support was introduced.
Thus, this commit will merge all the StuffRsb.inc files in UefiCpuPkg into
one file. The merged file will be named 'StuffRsbNasm.inc' and be placed
under folder UefiCpuPkg/Include/.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
*Excpetion* should be *Exception*
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Mike Maslenkin <mike.maslenkin@gmail.com>
CC: Eric Dong <eric.dong@intel.com>
CC: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1305
The patch reverts commit 1ed6498c4a
* UefiCpuPkg/CommonFeature: Skip locking when the feature is disabled
FEATURE_CONTROL.Lock bit is controlled by feature
CPU_FEATURE_LOCK_FEATURE_CONTROL_REGISTER. The commit 1ed649 fixes
a bug that when the feature is disabled, the Lock bit is cleared.
But it's a security hole if the bit is cleared when booting OS.
We can argue that platform needs to make sure the value
of PcdCpuFeaturesUserConfiguration should be set properly to make
sure feature CPU_FEATURE_LOCK_FEATURE_CONTROL_REGISTER is enabled.
But it's better to guarantee this in the generic core code.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
In current implementation, core and package level sync uses same semaphores.
Sharing the semaphore may cause wrong execution order.
For example:
1. Feature A has CPU_FEATURE_CORE_BEFORE dependency with Feature B.
2. Feature C has CPU_FEATURE_PACKAGE_AFTER dependency with Feature B.
The expected feature initialization order is A B C:
A ---- (Core Depends) ----> B ---- (Package Depends) ----> C
For a CPU has 1 package, 2 cores and 4 threads. The feature initialization
order may like below:
Thread#1 Thread#2 Thread#3 Thread#4
[A.Init] [A.Init] [A.Init]
Release(S1, S2) Release(S1, S2) Release(S3, S4)
Wait(S1) * 2 Wait(S2) * 2 <------------------------------- Core sync
[B.Init] [B.Init]
Release (S1,S2,S3,S4)
Wait (S1) * 4 <----------------------------------------------------- Package sync
Wait(S4 * 2) <- Core sync
[B.Init]
In above case, for thread#4, when it syncs in core level, Wait(S4) * 2 isn't
blocked and [B.Init] runs. But [A.Init] hasn't run in thread#3. It's wrong!
Thread#4 should execute [B.Init] after thread#3 executes [A.Init] because B
core level depends on A.
The reason of the wrong execution order is that S4 is released in thread#1
by calling Release (S1, S2, S3, S4) and in thread #4 by calling
Release (S3, S4).
To fix this issue, core level sync and package level sync should use separate
semaphores.
In above example, the S4 released in Release (S1, S2, S3, S4) should not be the
same semaphore as that in Release (S3, S4).
Related BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1311
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
V2 changes:
V1 change has regression which caused by change feature order.
V2 changes logic to detect dependence not only for the
neighborhood features. It need to check all features in the list.
V1 Changes:
In current code logic, only adjust feature position if current
CPU feature position not follow the request order. Just like
Feature A need to be executed before feature B, but current
feature A registers after feature B. So code will adjust the
position for feature A, move it to just before feature B. If
the position already met the requirement, code will not adjust
the position.
This logic has issue when met all below cases:
1. feature A has core or package level dependence with feature B.
2. feature A is register before feature B.
3. Also exist other features exist between feature A and B.
Root cause is driver ignores the dependence for this case, so
threads may execute not follow the dependence order.
Fix this issue by change code logic to adjust feature position
for CPU features which has dependence relationship.
Related BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1311
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1305
Today's code unconditionally sets the IA32_FEATURE_CONTROL.Lock to 1
no matter the feature is enabled or not.
The patch fixes this issue by only setting the Lock bit to 1 when
the feature is enabled.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
In some special cases, after BSP sends Init-sipi-sipi signal
AP needs more time to start the Ap procedure. In this case
BSP may think AP has finished its task but in fact AP hasn't began
yet.
Rollback former change to keep the status which only be used
when AP really finished task.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Build UefiCpuPkg with below configuration:
Architecture(s) = IA32
Build target = NOOPT
Toolchain = VS2015x86
Below error info shows up:
DxeRegisterCpuFeaturesLib.lib(CpuFeaturesInitialize.obj) :
error LNK2001: unresolved external symbol __allmul
Valid mDependTypeStr type only have 5 items, use UINT32 type cast
to fix this error.
Cc: Dandan Bi <dandan.bi@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Index is initialized to MAX_UINT16 as default failure value, which
is what the ASSERT is supposed to test for. The ASSERT condition
however can never return FALSE for INT16 != int, as due to
Integer Promotion[1], Index is converted to int, which can never
result in -1.
Furthermore, Index is used as a for loop index variable inbetween its
initialization and the ASSERT, so the value is unconditionally
overwritten too.
Fix the ASSERT check to compare Index to its upper boundary, which it
will be equal to if the loop was not broken out of on success.
[1] ISO/IEC 9899:2011, 6.5.9.4
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Marvin Haeuser <Marvin.Haeuser@outlook.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Current code assume only one dependence (before or after) for one
feature. Enhance code logic to support feature has two dependence
(before and after) type.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Changes include:
1. Remove extra white space at the end of line.
2. Add comments for the new add function parameter.
3. Update IN OUT tag for function parameter.
Cc: Dandan Bi <dandan.bi@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Remove extra white space at the end of line.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Code initialized in function can't be correctly detected by build tool.
Add code to clearly initialize the local variable before use it.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Because MSR has scope attribute, driver has no needs to set
MSR for all APs if MSR scope is core or package type. This patch
updates code to base on the MSR scope value to add MSR to the register
table.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
V4 changes include:
1. Serial debug message for different threads when program the register table.
V3 changes include:
1. Use global variable instead of internal function to return string for register type
and dependence type.
2. Add comments for some complicated logic.
V2 changes include:
1. Add more description for the code part which need easy to understand.
2. Refine some code base on feedback for V1 changes.
V1 changes include:
In a system which has multiple cores, current set register value task costs huge times.
After investigation, current set MSR task costs most of the times. Current logic uses
SpinLock to let set MSR task as an single thread task for all cores. Because MSR has
scope attribute which may cause GP fault if multiple APs set MSR at the same time,
current logic use an easiest solution (use SpinLock) to avoid this issue, but it will
cost huge times.
In order to fix this performance issue, new solution will set MSRs base on their scope
attribute. After this, the SpinLock will not needed. Without SpinLock, new issue raised
which is caused by MSR dependence. For example, MSR A depends on MSR B which means MSR A
must been set after MSR B has been set. Also MSR B is package scope level and MSR A is
thread scope level. If system has multiple threads, Thread 1 needs to set the thread level
MSRs and thread 2 needs to set thread and package level MSRs. Set MSRs task for thread 1
and thread 2 like below:
Thread 1 Thread 2
MSR B N Y
MSR A Y Y
If driver don't control execute MSR order, for thread 1, it will execute MSR A first, but
at this time, MSR B not been executed yet by thread 2. system may trig exception at this
time.
In order to fix the above issue, driver introduces semaphore logic to control the MSR
execute sequence. For the above case, a semaphore will be add between MSR A and B for
all threads. Semaphore has scope info for it. The possible scope value is core or package.
For each thread, when it meets a semaphore during it set registers, it will 1) release
semaphore (+1) for each threads in this core or package(based on the scope info for this
semaphore) 2) acquire semaphore (-1) for all the threads in this core or package(based
on the scope info for this semaphore). With these two steps, driver can control MSR
sequence. Sample code logic like below:
//
// First increase semaphore count by 1 for processors in this package.
//
for (ProcessorIndex = 0; ProcessorIndex < PackageThreadsCount ; ProcessorIndex ++) {
LibReleaseSemaphore ((UINT32 *) &SemaphorePtr[PackageOffset + ProcessorIndex]);
}
//
// Second, check whether the count has reach the check number.
//
for (ProcessorIndex = 0; ProcessorIndex < ValidApCount; ProcessorIndex ++) {
LibWaitForSemaphore (&SemaphorePtr[ApOffset]);
}
Platform Requirement:
1. This change requires register MSR setting base on MSR scope info. If still register MSR
for all threads, exception may raised.
Known limitation:
1. Current CpuFeatures driver supports DXE instance and PEI instance. But semaphore logic
requires Aps execute in async mode which is not supported by PEI driver. So CpuFeature
PEI instance not works after this change. We plan to support async mode for PEI in phase
2 for this task.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1237
Sometimes the memory will be contaminated by random data left in last
boot (warm reset). The code should not assume the allocated memory is
always filled with zero. This patch add code to clear data structure
used for stack switch to prevent such problem from happening.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
The PCD below is unused, so it has been removed from inf.
gUefiCpuPkgTokenSpaceGuid.PcdCpuFeaturesSupport
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: shenglei <shenglei.zhang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1187
The patch reverts 9c8c4478cf
"UefiCpuPkg/MtrrLib: Skip Base MSR access when the pair is invalid".
Microsoft Windows will report an error in event manager if MTRR
usage is different across hibernate even when the difference is
in an non valid MTRR pair. This seems like a bug in Windows but
for compatibility and servicing reasons we think a change in UEFI
would wise.
A Windows change has already been submitted for the next iteration
(2019 time frame).
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Sean Brogan <sean.brogan@microsoft.com>
Zhichao Gao
Ray Ni
Star Zeng
Joe Richey
Michael D Kinney
Eric Dong
Shenglei Zhang
Chen A Chen
Jian J Wang
Jiewen Yao
Ruiyu Ni
Hao Wu
Mike Maslenkin
Marvin H?user