BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3275
Use the SEV-SNP AP Creation NAE event to create and launch APs under
SEV-SNP. This capability will be advertised in the SEV Hypervisor
Feature Support PCD (PcdSevEsHypervisorFeatures).
Cc: Michael Roth <michael.roth@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Min Xu <min.m.xu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Ray Ni <ray.ni@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
During AP bringup, just after switching to long mode, APs will do some
cpuid calls to verify that the extended topology leaf (0xB) is available
so they can fetch their x2 APIC IDs from it. In the case of SEV-ES,
these cpuid instructions must be handled by direct use of the GHCB MSR
protocol to fetch the values from the hypervisor, since a #VC handler
is not yet available due to the AP's stack not being set up yet.
For SEV-SNP, rather than relying on the GHCB MSR protocol, it is
expected that these values would be obtained from the SEV-SNP CPUID
table instead. The actual x2 APIC ID (and 8-bit APIC IDs) would still
be fetched from hypervisor using the GHCB MSR protocol however, so
introducing support for the SEV-SNP CPUID table in that part of the AP
bring-up code would only be to handle the checks/validation of the
extended topology leaf.
Rather than introducing all the added complexity needed to handle these
checks via the CPUID table, instead let the BSP do the check in advance,
since it can make use of the #VC handler to avoid the need to scan the
SNP CPUID table directly, and add a flag in ExchangeInfo to communicate
the result of this check to APs.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Min Xu <min.m.xu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Ray Ni <ray.ni@intel.com>
Suggested-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3275
An SEV-SNP guest requires that the physical address of the GHCB must
be registered with the hypervisor before using it. See the GHCB
specification section 2.3.2 for more details.
Cc: Michael Roth <michael.roth@amd.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Min Xu <min.m.xu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Ray Ni <ray.ni@Intel.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3275
Previous commit introduced a generic confidential computing PCD that can
determine whether AMD SEV-ES is enabled. Update the MpInitLib to drop the
PcdSevEsIsEnabled in favor of PcdConfidentialComputingAttr.
Cc: Michael Roth <michael.roth@amd.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Min Xu <min.m.xu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Ray Ni <ray.ni@intel.com>
Suggested-by: Jiewen Yao <jiewen.yao@intel.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3275
Move all the SEV specific function in AmdSev.c.
No functional change intended.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Michael Roth <michael.roth@amd.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Min Xu <min.m.xu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ard Biesheuvel <ardb+tianocore@kernel.org>
Cc: Erdem Aktas <erdemaktas@google.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Suggested-by: Jiewen Yao <Jiewen.yao@intel.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3737
Apply uncrustify changes to .c/.h files in the UefiCpuPkg package
Cc: Andrew Fish <afish@apple.com>
Cc: Leif Lindholm <leif@nuviainc.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Signed-off-by: Michael Kubacki <michael.kubacki@microsoft.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3767
Update use of DEBUG_CODE(Expression) if Expression is a complex code
block with if/while/for/case statements that use {}.
Cc: Andrew Fish <afish@apple.com>
Cc: Leif Lindholm <leif@nuviainc.com>
Cc: Michael Kubacki <michael.kubacki@microsoft.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3760
Update all use of ', OPTIONAL' to ' OPTIONAL,' for function params.
Cc: Andrew Fish <afish@apple.com>
Cc: Leif Lindholm <leif@nuviainc.com>
Cc: Michael Kubacki <michael.kubacki@microsoft.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
When CET shadow stack feature is enabled, it needs to use IST for the
exceptions, and uses interrupt shadow stack for the stack switch.
Shadow stack should be 32 bytes aligned.
Check IST field, when clear shadow stack token busy bit when using retf.
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3728
Signed-off-by: Sheng Wei <w.sheng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3698
Lots of code relies on CPU Family/Model/Stepping for different logics.
The change adds two APIs for such needs.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
When using UT_ASSERT_EQUAL() on a pointer value, it must be
cast to UINTN. This follows the samples provided with the
UnitTestFrameworkPkg.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3634
The memory allocated through "PeiAllocatePool" is located in HOB, and
in DXE phase, the HOB will be migrated to a different location.
After the migration, the data stored in the HOB stays the same, but the
address of pointer to the memory(such as the pointers in ACPI_CPU_DATA
structure) changes, which may cause "PiSmmCpuDxeSmm" driver can't find
the memory(the pointers in ACPI_CPU_DATA structure) that allocated in
"PeiRegisterCpuFeaturesLib", so use "PeiAllocatePages" to allocate
memory instead.
Signed-off-by: Jason Lou <yun.lou@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3621
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3631
Refactor initialization of CPU features during S3 resume.
In addition, the macro ACPI_CPU_DATA_STRUCTURE_UPDATE is used to fix
incompatibility issue caused by ACPI_CPU_DATA structure update. It will
be removed after all the platform code uses new ACPI_CPU_DATA structure.
Signed-off-by: Jason Lou <yun.lou@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3508
Sort the CpuCacheInfo array by CPU package ID, core type, cache level
and cache type.
Signed-off-by: Jason Lou <yun.lou@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
When enter SMM exception, there will be a stack switch only if the IST
field of the interrupt gate is set. When CET shadow stack feature is
enabled, if there is a stack switch between SMM exception and SMM, the
shadow stack token busy bit needs to be cleared when return from SMM
exception to SMM. In UEFI BIOS, only page fault exception does the stack
swith when SMM shack guard feature is enabled. The condition of clear
shadow stack token busy bit should be SMM stack guard enabled, CET shadows
stack feature enabled and page fault exception.
The shadow stack token should be initialized by UINT64.
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3462
Signed-off-by: Sheng Wei <w.sheng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Qihua Zhuang <qihua.zhuang@intel.com>
Cc: Daquan Dong <daquan.dong@intel.com>
Cc: Justin Tong <justin.tong@intel.com>
Cc: Tom Xu <tom.xu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3424
Processor location information check needs to updated
When Core 0 is disabled.
In C1e.c, change MSR_FEATURE_CONFIG to MSR_NEHALEM_POWER_CTL in comments
to match the correct MSR name.
Signed-off-by: Daoxiang Li <daoxiang.li@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3324
The SEV-ES stacks currently share a page with the reset code and data.
Separate the SEV-ES stacks from the reset vector code and data to avoid
possible stack overflows from overwriting the code and/or data.
When SEV-ES is enabled, invoke the GetWakeupBuffer() routine a second time
to allocate a new area, below the reset vector and data.
Both the PEI and DXE versions of GetWakeupBuffer() are changed so that
when PcdSevEsIsEnabled is true, they will track the previous reset buffer
allocation in order to ensure that the new buffer allocation is below the
previous allocation. When PcdSevEsIsEnabled is false, the original logic
is followed.
Fixes: 7b7508ad78
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Marvin Häuser <mhaeuser@posteo.de>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <3cae2ac836884b131725866264e0a0e1897052de.1621024125.git.thomas.lendacky@amd.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3373
An update to expand the mExceptionNameStr array failed to add a comma
after original last entry, therefore causing the #CP name to have extra
incorrect characters and the remaining entries to be indexed incorrectly
(off by 1).
Add a comma after the "#CP" entry to resolve this issue.
Fixes: 5277540e37
Cc: Allen Wynn <Allen_Wynn@Dell.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <40e55bf6563ed8ea4962a1219efbe1ab77a56cc4.1620919615.git.thomas.lendacky@amd.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=3385
A VS2012 build fails with a cast conversion warning when the SEV-ES work
area PCD is cast as a pointer to the SEV_ES_AP_JMP_FAR type.
When casting from a PCD value to a pointer, the cast should first be done
to a UINTN and then to the pointer. Update the code to perform a cast to
a UINTN before casting to a pointer to the SEV_ES_AP_JMP_FAR type.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Fixes: 7b7508ad78
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <c89bc819856d448360430c32cb3833a9667f987b.1620656694.git.thomas.lendacky@amd.com>
Reviewed-by: Liming Gao <gaoliming@byosoft.com.cn>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2832
Update LIBRARY_CLASS of BaseCpuTimerLib to remove the usage limitation,
otherwise the Base instance cannot be used in some types of modules.
Signed-off-by: Jason Lou <yun.lou@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2832
1. Remove PEI instance(PeiCpuTimerLib).
PeiCpuTimerLib is currently designed to save time by getting CPU TSC
frequency from Hob. BaseCpuTimerLib is designed to calculate TSC frequency
by using CPUID[15h] each time.
The time it takes to find CpuCrystalFrequencyHob (about 2000ns) is much
longer than it takes to calculate TSC frequency with CPUID[15h] (about
450ns), which means using BaseCpuTimerLib to trigger a delay is more
accurate than using PeiCpuTimerLib, recommend to use BaseCpuTimerLib
instead of PeiCpuTimerLib.
2. Remove DXE instance(DxeCpuTimerLib).
DxeCpuTimerLib is designed to calculate TSC frequency with CPUID[15h] in
its constructor function, then save it in a global variable. For this
design, once the driver containing this instance is running, this
constructor function is called, it will take extra time to calculate TSC
frequency.
The time it takes to get TSC frequency from global variable is shorter
than it takes to calculate TSC frequency with CPUID[15h], but 450ns is a
short time, the impact on the platform is very limited.
In addition, in order to simplify the code, recommend to use
BaseCpuTimerLib instead of DxeCpuTimerLib.
I did some experiments on one server platform and collected following data:
1. Average time required to find CpuCrystalFrequencyHob: about 2000 ns.
2. Average time required to find the last Hob: about 2700 ns.
2. Average time required to calculate TSC frequency: about 450 ns.
Reference code:
//
// Calculate average time required to find Hob.
//
DEBUG((DEBUG_ERROR, "[PeiCpuTimerLib] GetPerformanceCounterFrequency - GetFirstGuidHob (1000 cycles)\n"));
Ticks1 = AsmReadTsc();
for (i = 0; i < 1000; i++) {
GuidHob = GetFirstGuidHob (&mCpuCrystalFrequencyHobGuid);
}
Ticks2 = AsmReadTsc();
if (GuidHob == NULL) {
DEBUG((DEBUG_ERROR, "[PeiCpuTimerLib] - CpuCrystalFrequencyHob can not be found!\n"));
} else {
DEBUG((DEBUG_ERROR, "[PeiCpuTimerLib] - Average time required to find Hob = %d ns\n", \
DivU64x32(DivU64x64Remainder(MultU64x32((Ticks2 - Ticks1), 1000000000), *CpuCrystalCounterFrequency, NULL), 1000)));
}
//
// Calculate average time required to calculate CPU frequency.
//
DEBUG((DEBUG_ERROR, "[PeiCpuTimerLib] GetPerformanceCounterFrequency - CpuidCoreClockCalculateTscFrequency (1000 cycles)\n"));
Ticks1 = AsmReadTsc();
for (i = 0; i < 1000; i++) {
Freq = CpuidCoreClockCalculateTscFrequency ();
}
Ticks2 = AsmReadTsc();
DEBUG((DEBUG_ERROR, "[PeiCpuTimerLib] - Average time required to calculate TSC frequency = %d ns\n", \
DivU64x32(DivU64x64Remainder(MultU64x32((Ticks2 - Ticks1), 1000000000), *CpuCrystalCounterFrequency, NULL), 1000)));
Signed-off-by: Jason Lou <yun.lou@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
MpInitLib contains a function MicrocodeDetect() which is called by
all threads as an AP procedure.
Today this function contains below code:
if (CurrentRevision != LatestRevision) {
AcquireSpinLock(&CpuMpData->MpLock);
DEBUG ((
EFI_D_ERROR,
"Updated microcode signature [0x%08x] does not match \
loaded microcode signature [0x%08x]\n",
CurrentRevision, LatestRevision
));
ReleaseSpinLock(&CpuMpData->MpLock);
}
When the if-check is passed, the code may call into PEI services:
1. AcquireSpinLock
When the PcdSpinTimeout is not 0, TimerLib
GetPerformanceCounterProperties() is called. And some of the
TimerLib implementations would get the information cached in
HOB. But AP procedure cannot call PEI services to retrieve the
HOB list.
2. DEBUG
Certain DebugLib relies on ReportStatusCode services and the
ReportStatusCode PPI is retrieved through the PEI services.
DebugLibSerialPort should be used.
But when SerialPortLib is implemented to depend on PEI services,
even using DebugLibSerialPort can still cause AP calls PEI
services resulting hang.
It causes a lot of debugging effort on the platform side.
There are 2 options to fix the problem:
1. make sure platform DSC chooses the proper DebugLib and set the
PcdSpinTimeout to 0. So that AcquireSpinLock and DEBUG don't call
PEI services.
2. remove the AcquireSpinLock and DEBUG call from the procedure.
Option #2 is preferred because it's not practical to ask every
platform DSC to be written properly.
Following option #2, there are two sub-options:
2.A. Just remove the if-check.
2.B. Capture the CurrentRevision and ExpectedRevision in the memory
for each AP and print them together from BSP.
The patch follows option 2.B.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3265
Support collecting cache associative type in CpuCacheInfoLib.
This prevents the user from using additional code to obtain the
same information.
Signed-off-by: Jason Lou <yun.lou@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=3218
Adds an INF for StandaloneMmCpuFeaturesLib, which supports building
the SmmCpuFeaturesLib code for Standalone MM. Minimal code changes
are made to allow reuse of existing code for Standalone MM.
The original INF file names are left intact (continue to use SMM
terminology) to retain backward compatibility with platforms that
use those INFs. Similarly, the pre-existing C file names are
unchanged to be consistent with the INF file names.
Note that all references in library source files to PiSmm.h have
been changed to PiMm.h for consistency.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Michael Kubacki <michael.kubacki@microsoft.com>
Message-Id: <20210217213227.1277-6-mikuback@linux.microsoft.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
REF:https://bugzilla.tianocore.org/show_bug.cgi?id=3218
Adds a new function called GetCpuMaxLogicalProcessorNumber() to
return the number of maximum CPU logical processors (currently
gUefiCpuPkgTokenSpaceGuid.PcdCpuMaxLogicalProcessorNumber).
This allows the the mechanism used to retrieve the CPU maximum
logical processor number to be abstracted from the logic that
needs the value.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Michael Kubacki <michael.kubacki@microsoft.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20210217213227.1277-5-mikuback@linux.microsoft.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
There's currently two library instances:
1. SmmCpuFeaturesLib
2. SmmCpuFeaturesLibStm
There's two constructor functions:
1. SmmCpuFeaturesLibConstructor()
2. SmmCpuFeaturesLibStmConstructor()
SmmCpuFeaturesLibConstructor() is called by
SmmCpuFeaturesLibStmConstructor() since the functionality in that
function is required by both library instances.
The declaration for SmmCpuFeaturesLibConstructor() is embedded in
"SmmStm.c" instead of being declared in a header file. Further,
that constructor function is called by the STM specific constructor.
This change moves the common code to a function called
CpuFeaturesLibInitialization() which is declared in an internal
library header file "CpuFeaturesLib.h". Each constructor simply
calls this function to perform the common functionality.
Additionally, SmmCpuFeaturesLibConstructor() is moved from
SmmCpuFeaturesLibNoStm.c into a instance-specific file allowing
SmmCpuFeaturesLibNoStm.c to contain no STM implementation agnostic
to a particular library instance.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Michael Kubacki <michael.kubacki@microsoft.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20210217213227.1277-4-mikuback@linux.microsoft.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
This change renames SmmCpuFeaturesLib.c to SmmCpuFeaturesLibCommon.c
to better convey that this file contains library implementation
common to all library instances.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Michael Kubacki <michael.kubacki@microsoft.com>
Message-Id: <20210217213227.1277-3-mikuback@linux.microsoft.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
FinishSmmCpuFeaturesInitializeProcessor() is a multi-instance
internal library function that is currently not declared in a
header file but embedded in "SmmCpuFeaturesLib.c".
This change cleans up the declaration moving it to a new header
file "CpuFeaturesLib.h" and removing the local declaration in
"SmmCpuFeaturesLib.c".
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Michael Kubacki <michael.kubacki@microsoft.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20210217213227.1277-2-mikuback@linux.microsoft.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
[lersek@redhat.com: replace the guard macro "_CPU_FEATURES_LIB_H_" with
"CPU_FEATURES_LIB_H_", for fixing ECC 8003, per commit 6ffbb3581a]
The Lock is no longer needed since "LOCK XADD" was used in
MpFuncs.nasm for ApIndex atomic increment.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
In Windows environment, "dumpbin /disasm" is used to verify the
disassembly before and after using NASM struc doesn't change.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
If CET shadows stack feature enabled in SMM and stack switch is enabled.
When code execute from SMM handler to SMM exception, CPU will check SMM
exception shadow stack token busy bit if it is cleared or not.
If it is set, it will trigger #DF exception.
If it is not set, CPU will set the busy bit when enter SMM exception.
So, the busy bit should be cleared when return back form SMM exception to
SMM handler. Otherwise, keeping busy bit 1 will cause to trigger #DF
exception when enter SMM exception next time.
So, we use instruction SAVEPREVSSP, CLRSSBSY and RSTORSSP to clear the
shadow stack token busy bit before RETF instruction in SMM exception.
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3192
Signed-off-by: Sheng Wei <w.sheng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Roger Feng <roger.feng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
When AP firstly wakes up, MpFuncs.nasm contains below logic to assign
an unique ApIndex to each AP according to who comes first:
---ASM---
TestLock:
xchg [edi], eax
cmp eax, NotVacantFlag
jz TestLock
mov ecx, esi
add ecx, ApIndexLocation
inc dword [ecx]
mov ebx, [ecx]
Releaselock:
mov eax, VacantFlag
xchg [edi], eax
---ASM END---
"lock inc" cannot be used to increase ApIndex because not only the
global ApIndex should be increased, but also the result should be
stored to a local general purpose register EBX.
This patch learns from the NASM implementation of
InternalSyncIncrement() to use "XADD" instruction which can increase
the global ApIndex and store the original ApIndex to EBX in one
instruction.
With this patch, OVMF when running in a 255 threads QEMU spends about
one second to wakeup all APs. Original implementation needs more than
10 seconds.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3195
Support system has no enabled AP case in DxeCpuCacheInfoLib.
Otherwise, if the system only has 1 BSP without any enabled AP,
UEFI POST hangs when invoking StartupAllAPs protocol because
EFI_NOT_STARTED is returned.
Signed-off-by: Jason Lou <yun.lou@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3190
Add MpService dependency to enforce the executability of CpuCacheInfoLib.
Signed-off-by: Jason Lou <yun.lou@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
This change of SmmCpuExceptionHandlerLib adds support for StandaloneMm
components to allow x64 StandaloneMm environment setting up exception
handlers.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Signed-off-by: Kun Qin <kun.q@outlook.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3179
When BSP first time wakes all APs, each AP atomically increases
CpuMpData->CpuCount and CpuMpData->FinishedCount.
Each AP atomically increases CpuMpData->NumApsExecuting
in early assembly code and decreases it before it enters to HLT or
MWAIT state.
Putting them together, the 3 variables are changed in the following order:
1. NumApsExecuting++ // in assembly
2. CpuCpunt++
4. FinishedCount++
3. NumApsExecuting-- // in C
BSP waits for a certain timeout and then polls NumApsExecuting
until it drops to zero. It assumes all APs are waken up concurrently
and NumApsExecuting only drops to zero when all APs have checked in.
Then it additionally waits for FinishedCount == CpuCount - 1. (FinishedCount doesn't include BSP while CpuCount includes BSP.)
There is no need to additionally wait for
FinishedCount == CpuCount - 1 because when NumApsExecuting == 0,
the number of increament of FinishedCount and CpuCount should equal.
This patch simplifies the code to remove "CpuCount++" in
ApWakeupFunction() and
assigns FinishedCount + 1 to CpuCount after WakeUpAP().
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3105
Change and add some macro definitions about
CPUID_HYBRID_INFORMATION Leaf(1Ah).
Signed-off-by: Jason Lou <yun.lou@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Liming Gao <gaoliming@byosoft.com.cn>
Cc: Zhiguang Liu <zhiguang.liu@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3182
Fix the order of operations in ApWakeupFunction() when PcdCpuApLoopMode
is set to HLT mode that uses INIT-SIPI-SIPI to wake APs. In this mode,
volatile state is restored and saved each time a INIT-SIPI-SIPI is sent
to an AP to request a function to be executed on the AP. When the
function is completed the volatile state of the AP is saved. However,
the counters NumApsExecuting and FinishedCount are updated before
the volatile state is saved. This allows for a race condition window
for the BSP that is waiting on these counters to request a new
INIT-SIPI-SIPI before all the APs have completely saved their volatile
state. The fix is to save the AP volatile state before updating the
NumApsExecuting and FinishedCount counters.
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
NumberOfCpus local variable in GetAcpiCpuData will be uninitialized
when CpuS3DataDxe runs before DxeRegisterCpuFeaturesLib (linked by
CpuFeaturesDxe) because there is no code to initialize it at
(AcpiCpuData != NULL) execution path.
The issue is exposed after cefad282fb
and 38ee7bafa7.
There was negligence in that code review.
One further topic may be "Could EDK2 CI be enhanced to catch this kind
of uninitialized local variable case?". :)
This patch fixes this regression issue.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Message-Id: <20210121093944.1621-1-star.zeng@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
There are lots of fields in ACPI_CPU_DATA structure while only
followings are accessed by CpuFeature infra:
* NumberOfCpus
* PreSmmInitRegisterTable // pointer
* RegisterTable // pointer
* CpuStatus
* ApLocation // pointer
So it's possible that an implementation of CpuS3DataDxe doesn't
allocate memory for PreSmmInitRegisterTable/RegisterTable/ApLocation.
This patch handles the case when CpuS3DataDxe doesn't allocate
memory for PreSmmInitRegisterTable/RegisterTable.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=3159
Signed-off-by: Ray Ni <ray.ni@intel.com>
[lersek@redhat.com: update CC list, add BZ reference, add my S-o-b]
[lersek@redhat.com: deal with RegisterTable and PreSmmInitRegisterTable
being zero independently of each other; replacing the ASSERT()]
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20210119155440.2262-2-lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=3105
This new library uses a platform agnostic algorithm to get CPU
cache information. It provides user with an API(GetCpuCacheInfo)
to get detailed CPU cache information by each package, each core
type included in this package, and each cache level & type.
This library can be used by code that produces SMBIOS_TABLE_TYPE7
SMBIOS table.
Signed-off-by: Jason Lou <yun.lou@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Rahul Kumar <rahul1.kumar@intel.com>
This patch fixed the hang in UEFICpuPkg when it is dispatched above 4GB.
In UEFI BIOS case CpuInfoInHob is provided to DXE under 4GB from PEI.
When using UEFI payload and bootloaders, CpuInfoInHob will be allocated
above 4GB since it is not provided from bootloader. so we need update
the code to make sure this hob could be accessed correctly in this case.
Signed-off-by: Guo Dong <guo.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
CpuInfo.First stores whether the current thread belongs to the first
package in the platform, first core in a package, first thread in a
core.
But the time complexity of original algorithm to calculate the
CpuInfo.First is O (n) * O (p) * O (c).
n: number of processors
p: number of packages
c: number of cores per package
The patch trades time with space by storing the first package, first
core per package, first thread per core in an array.
The time complexity becomes O (n).
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Yun Lou <yun.lou@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
The required buffer size for InitOrder will be 96K when NumberOfCpus=1024.
sizeof (CPU_FEATURES_INIT_ORDER) = 96
NumberOfCpus = 1024 = 1K
sizeof (CPU_FEATURES_INIT_ORDER) * NumberOfCpus = 96K
AllocateZeroPool() will call to PeiServicesAllocatePool() which will use
EFI_HOB_MEMORY_POOL to management memory pool.
EFI_HOB_MEMORY_POOL.Header.HobLength is UINT16 type, so there is no way
for AllocateZeroPool() to allocate > 64K memory.
So AllocateZeroPool() could not be used anymore for the case above or
even bigger required buffer size.
This patch updates the code to use AllocatePages() instead of
AllocateZeroPool() to allocate buffer for InitOrder.
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Today's code assumes every core contains the same number of threads.
It's not always TRUE for certain model.
Such assumption causes system hang when thread count per core
is different and there is core or package dependency between CPU
features (using CPU_FEATURE_CORE_BEFORE/AFTER,
CPU_FEATURE_PACKAGE_BEFORE/AFTER).
The change removes such assumption by calculating the actual thread
count per package and per core.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Yun Lou <yun.lou@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Tom Lendacky
Michael Roth
Brijesh Singh
Michael Kubacki
Michael D Kinney
Sheng, W
Ni, Ray
IanX Kuo
Lou, Yun
Daoxiang Li
Kun Qin
Zeng, Star
Guo Dong