MpInitLib sets X2ApicEnable in two places.
1. CollectProcessorCount()
This function is called when MpInitLibInitialize() hasn't been
called before.
It sets X2ApicEnable and later in the same function it configures
all CPUs to operate in X2 APIC mode.
2. MpInitLibInitialize()
The X2ApicEnable setting happens when this function is called in
second time. But after that setting, no code consumes that flag.
With the above analysis and with the purpose of simplifying the code,
the X2ApicEnable in #1 is changed to local variable and the #2 can be
changed to remove the setting of X2ApicEnable.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Today's logic sets X2ApicEnable flag in each AP's initialization
path when InitFlag == ApInitConfig.
Since all CPUs update the same global data, a spin-lock is used
to avoid modifications from multiple CPUs happen at the same time.
The spin-lock causes two problems:
1. Potential performance downgrade.
2. Undefined behavior when improper timer lib is used.
For example we saw certain platforms used AcpiTimerLib from
PcAtChipsetPkg and that library depends on retrieving PeiServices
from idtr. But in fact AP's (idtr - 4) doesn't point to
PeiServices.
The patch simplifies the code to let BSP set the X2ApicEnable flag so
the spin-lock acquisition from AP is not needed any more.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
- If a platform boots such that the boot CPU count is smaller than
PcdCpuMaxLogicalProcessorNumber, then the platform cannot use the "fast
AP detection" logic added in commit 6e1987f19a. (Which has been
documented as a subset of use case (2) in the previous patch.)
Said logic depends on the boot CPU count being equal to
PcdCpuMaxLogicalProcessorNumber. If the equality does not hold, the
platform either has to wait too long, or risk missing APs due to an
early timeout.
- The platform may not be able to use the variant added in commit
0594ec417c either. (Which has been documented as use case (1) in the
previous patch.)
See commit 861218740d. When OVMF runs on QEMU/KVM, APs may check in
with the BSP in arbitrary order, plus the individual AP may take
arbitrarily long to check-in. If "NumApsExecuting" falls to zero
mid-enumeration, APs will be missed.
Allow platforms to specify the exact boot CPU count, independently of
PcdCpuMaxLogicalProcessorNumber. In this mode, the BSP waits for all APs
to check-in regardless of timeout. If at least one AP fails to check-in,
then the AP enumeration hangs forever. That is the desired behavior when
the exact boot CPU count is known in advance. (A hung boot is better than
an AP checking-in after timeout, and executing code from released
storage.)
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1515
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Before adding another AP enumeration mode, clarify the documentation on
the current logic. No functional changes.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Ref: https://bugzilla.tianocore.org/show_bug.cgi?id=1515
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2150
v4:
The v3 posting didn't do what it promised to do, so do it now for real.
V3 changes:
change to mov instruction (non locking instuction) instead
of xchg to simplify design.
V2 changes:
Add xchg 16 bit instructions to handle sgdt and sidt base
63:48 bits and 47:32 bits.
Add comment to explain why xchg 64bit isnt being used
Split lock happens when a locking instruction is used on mis-aligned data
that crosses two cachelines. If close source platform enables Alignment
Check Exception(#AC), They can hit a double fault due to split lock being
in CpuExceptionHandlerLib.
sigt and sgdt saves 10 bytes to memory, 8 bytes is base and 2 bytes is limit.
The data is mis-aligned, can cross two cacheline, and a xchg
instruction(locking instuction) is being utilize.
Signed-off-by: John E Lofgren <john.e.lofgren@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1909
Cc: Ray Ni <ray.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Amy Chan <amy.chan@intel.com>
Cc: Rangasai V Chaganty <rangasai.v.chaganty@intel.com>
Signed-off-by: Donald Kuo <donald.kuo@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2040
Below code is current implementation:
if (MsrRegister[ProcessorNumber].Bits.Lock == 0) {
CPU_REGISTER_TABLE_WRITE_FIELD (
ProcessorNumber,
Msr,
MSR_IA32_FEATURE_CONTROL,
MSR_IA32_FEATURE_CONTROL_REGISTER,
Bits.Lock,
1
);
}
1. In first normal boot, the Bits.Lock is 0, 1 will be added
into the register table and then will set to the MSR.
2. Trig warm reboot, MSR value preserves. After normal boot phase,
the Bits.Lock is 1, so it will not be added into the register
table during the warm reboot phase.
3. Trig S3 then resume, the Bits.Lock change to 0 and Bits.Lock is
not added in register table, so it's still 0 after resume. This
is not an expect behavior. The expect value is the value should
always 1 after booting or resuming from S3.
The root cause for this issue is
1. driver bases on current value to insert the "set value action" to
the register table.
2. Some MSRs may reserve their value during warm reboot.
The solution for this issue is using new added macros for the MSRs which
preserve value during warm reboot.
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2040
Supports new logic which test current value before write new value.
Only write new value when current value not same as new value.
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2040
Add below new micros which test the current value before write the new
value. Only write new value when current value not same as new value.
CPU_REGISTER_TABLE_TEST_THEN_WRITE32
CPU_REGISTER_TABLE_TEST_THEN_WRITE64
CPU_REGISTER_TABLE_TEST_THEN_WRITE_FIELD
Also add below API:
CpuRegisterTableTestThenWrite
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Cc: Star Zeng <star.zeng@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2060
Remove the useless ConsoleLogLock spinlock.
Signed-off-by: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=2008
MpInitLib is the library that's responsible to wake up APs to provide
MP PPI and Protocol services.
The patch synchronizes BSP's CR4.LA57 to each AP's CR4.LA57.
Without this change, AP may enter to GP fault when BSP's 5-level page
table is set to AP during AP wakes up.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
This debug message may be called by BSP and APs. It may
caused ASSERT when APs call this debug code.
In order to avoid system boot assert, Remove this debug
message.
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1982
MpInitLibInitialize in MpLib.c will be invoked on both PEI and DXE
CPU code, MicrocodeDetect would be performed twice and copy
Microcode from flash to memory twice as well, which consider as
duplicate work to lead longer boot time.
This patch just use microcode memory copied in PEI phase if exist.
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1973
For semaphore type register, it required all processors to do the
task at the same time.
Current logic begins BSP's task after all APs have finished their tasks.
This will caused set semaphore task hang if semaphore has package
level type.
This patch use new EDKII_PEI_MP_SERVICES2_PPI to start all processors at
the same time to fix the potential hang issue.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1973
Add new MpInitLibStartupAllCPUs API uses to start all processors
at the same time.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1973
Add new MpInitLibStartupAllCPUs API uses to start all processors
at the same time.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1972
Function in this library may be used by APs. Assert will be trig if AP
uses dynamic pcd.
This patch enhance the current code, remove the unnecessary usage of
dynamic PCD. This change try to avoid report this issue again later.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1972
AP calls CollectProcessorData() to collect processor info.
CollectProcessorData function finally calls PcdGetSize function to
get DynamicPCD PcdCpuFeaturesSetting value. PcdGetSize will use
PeiServices table which caused below assert info:
Processor Info: Package: 1, MaxCore : 4, MaxThread: 1
Package: 0, Valid Core : 4
ASSERT [CpuFeaturesPei] c:\projects\jsl\jsl_v1193\Edk2\MdePkg\Library
\PeiServicesTablePointerLibIdt\PeiServicesTablePointer.c(48):
PeiServices != ((void *) 0)
This change uses saved global pcd size instead of calls PcdGetSize to
fix this issue.
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1968
The new VS2012 build failure is caused by 7a0df26.
xxx\registercpufeatureslib\dxeregistercpufeatureslib.c(258) :
warning C4701: potentially uninitialized local variable 'MpEvent' used
It is a false positive alarm.
MpEvent is assigned at line 238 and will be used at line 258, both
lines are controlled by "if (CpuFeaturesData->NumberOfCpus > 1)".
This patch initializes MpEvent to suppress incorrect compiler/analyzer
warnings.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1961
Enhance Ppin code to enable and unlock for TRUE State,
and disable and lock for FALSE State.
Note: enable and lock could not be set both.
According to SDM, once Enable_PPIN is set, attempt to write
1 to LockOut will cause #GP, and writing 1 to LockOut is
permitted only if Enable_PPIN is clear.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1968
We met assertion like below, it happens when there is only
one processor.
ASSERT_EFI_ERROR (Status = Not started)
ASSERT [CpuFeaturesDxe] X:\XXX\XXX\RegisterCpuFeaturesLib\
DxeRegisterCpuFeaturesLib.c(149): !EFI_ERROR (Status)
The code should not call StartupAllAPs when there is only one processor.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1934
0x0 MicrocodeBegin MicrocodeEntry MicrocodeEnd 0xffffffff
|--------------|---------------|---------------|---------------|
valid TotalSize
TotalSize is only valid between 0 and (MicrocodeEnd - MicrocodeEntry).
So add '(UINTN)MicrocodeEntryPoint > (MAX_ADDRESS - TotalSize)' before
'((UINTN)MicrocodeEntryPoint + TotalSize) > MicrocodeEnd' to make sure
((UINTN)MicrocodeEntryPoint + TotalSize) wouldn't overflow.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Liming Gao <liming.gao@intel.com>
Signed-off-by: Zhichao Gao <zhichao.gao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
The patch fixes the bug that the memory under 1MB is modified by
firmware in S3 boot.
Root cause is a racing condition in MpInitLib:
1. BSP: WakeUpByInitSipiSipi is set by NotifyOnS3SmmInitDonePpi()
2. BSP: WakeUpAP() wakes all APs to run certain procedure.
2.1. AllocateResetVector() uses <1MB memory for wake up vector.
2.1. FillExchangeInfoData() resets NumApsExecuting to 0.
2.2. WaitApWakeup() waits AP to clear WAKEUP_AP_SIGNAL.
3. AP: ApWakeupFunction() clears WAKEUP_AP_SIGNAL to inform BSP.
5. BSP: FreeResetVector() restores the <1MB memory
4. AP: ApWakeupFunction() calls the certain procedure.
4.1. NumApsExecuting is decreased.
#4.1 happens after the 1MB memory is restored so the result is
memory below 1MB is changed by #4.1
It happens only when the AP executes procedure a bit longer.
AP returns back to ApWakeupFunction() from procedure after
BSP restores the <1MB memory.
Since NumApsExecuting is only used when InitFlag == ApInitConfig
for counting the processor count.
The patch moves the NumApsExecuting decrease to the path when
InitFlag == ApInitConfig.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Nandagopal Sathyanarayanan <nandagopal.sathyanarayanan@intel.com>
NumApsExecuting is only used when InitFlag == ApInitConfig for
counting the processor count.
The patch changes Ia32 version of waking up vector assembly code
to align to x64 version of waking up vector assembly code.
After the change both versions of waking up vector increase
NumApsExecuting when InitFlag == ApInitConfig.
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1810
This patch covers two problems.
1. Current code gets CPUID_THERMAL_POWER_MANAGEMENT in
ClockModulationInitialize() and uses its ECMD bit for all processors.
But ClockModulationInitialize() is only executed by BSP, that means
the bit is just for BSP.
It may have no functionality issue as all processors may have same
bit value in a great possibility. But for good practice, the code
should get CPUID_THERMAL_POWER_MANAGEMENT in ClockModulationSupport
(executed by all processors), and then use them in
ClockModulationInitialize() for all processors.
We can see that Aesni.c (and others) have used this good practice.
2. Current code uses 3 CPU_REGISTER_TABLE_WRITE_FIELD for
MSR_IA32_CLOCK_MODULATION in ClockModulationInitialize(), they can
be reduced to 1 CPU_REGISTER_TABLE_WRITE64 by getting
MSR_IA32_CLOCK_MODULATION for all processors in
ClockModulationSupport() and then update fields for register table
write in ClockModulationInitialize().
We may argue that there may be more times of MSR_IA32_CLOCK_MODULATION
getting. But actually the times of MSR_IA32_CLOCK_MODULATION getting
could be also reduced.
The reason is in ProgramProcessorRegister() of CpuFeaturesInitialize.c,
AsmMsrBitFieldWrite64 (AsmReadMsr64 + AsmWriteMsr64) will be used for
CPU_REGISTER_TABLE_WRITE_FIELD, and AsmWriteMsr64 will be used for
CPU_REGISTER_TABLE_WRITE64.
The times of MSR accessing could be reduced with this patch.
Without the patch:
3 CPU_REGISTER_TABLE_WRITE_FIELD (in ClockModulationInitialize)
==> 3 AsmMsrBitFieldWrite64
==> 3 AsmReadMsr64 + 3 AsmWriteMsr64
With the patch:
1 AsmReadMsr64 (in ClockModulationSupport) +
1 CPU_REGISTER_TABLE_WRITE64 (in ClockModulationInitialize)
==> 1 AsmWriteMsr64
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1829
There will be ASSERT if LMCE is supported as below.
DXE_ASSERT!: [CpuFeaturesDxe]
XXX\UefiCpuPkg\Library\CpuCommonFeaturesLib\MachineCheck.c (342):
ConfigData != ((void *) 0)
The code should get Config Data and FeatureControlGetConfigData
could be used.
This issue is there since the code was added at the commit below.
Revision: 3d6275c113
Date: 2017/8/4 8:46:41
UefiCpuPkg CpuCommonFeaturesLib: Enable LMCE feature.
The commits below are also related to move the code.
Revision: 0233871442
Date: 2017/9/1 10:12:38
UefiCpuPkg/Lmce.c Remove useless file.
Revision: 306a5bcc6b
Date: 2017/8/17 11:40:38
UefiCpuPkg/CpuCommonFeaturesLib: Merge machine check code to same file.
So, the code may not be tested at all on a platform
that supports LMCE.
BTW: A typo in LmceInitialize is also fixed.
The typo is introduced by the commit below.
Revision: d28daaddb3
Date: 2018/10/17 9:24:05
UefiCpuPkg/CpuCommonFeaturesLib: Register MSR base on scope Info.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1808
In current code, the values of TopaEntryPtr->Uint64 for TopaTable
and the values of OutputBaseReg.Uint64 and OutputMaskPtrsReg.Uint64
to register table write for RTIT_OUTPUT_BASE and RTIT_OUTPUT_MASK_PTRS
are not been initialized in whole. For example, the reserved bits in
OutputBaseReg.Uint64 are random that will cause GP fault like below
when SetProcessorRegister (in CpuFeaturesInitialize.c) sets register
based on register table.
!!!! X64 Exception Type - 0D(#GP - General Protection)
CPU Apic ID - 00000000 !!!!
ExceptionData - 0000000000000000
RIP -0000000064D69576, CS -0000000000000038, RFLAGS -0000000000010246
RAX -000000006B9F1001, RCX -0000000000000560, RDX -0000000000000000
RBX -0000000064EECA18, RSP -000000006CB82BA0, RBP -0000000000000008
RSI -0000000080000000, RDI -0000000000000011
R8 -000000006B9493D0, R9 -0000000000000010, R10 -00000000000000FF
R11 -000000006CB82A50, R12 -0000000064D70F50, R13 -0000000066547050
R14 -0000000064E3E198, R15 -0000000000000000
DS -0000000000000030, ES -0000000000000030, FS -0000000000000030
GS -0000000000000030, SS -0000000000000030
CR0 -0000000080010013, CR2 -0000000000000000, CR3 -000000006C601000
CR4 -0000000000000628, CR8 -0000000000000000
DR0 -0000000000000000, DR1 -0000000000000000, DR2 -0000000000000000
DR3 -0000000000000000, DR6 -00000000FFFF0FF0, DR7 -0000000000000400
GDTR -000000006B8CCF18 0000000000000047, LDTR -0000000000000000
IDTR -000000006687E018 0000000000000FFF, TR -0000000000000000
FXSAVE_STATE -000000006CB82800
And current code gets MSR_IA32_RTIT_CTL, MSR_IA32_RTIT_OUTPUT_BASE and
MSR_IA32_RTIT_OUTPUT_MASK_PTRS in ProcTraceInitialize() and uses their
values for all processors. But ProcTraceInitialize() is only executed
by BSP, that means the values just for BSP. For good practice, the code
should get MSR_IA32_RTIT_CTL, MSR_IA32_RTIT_OUTPUT_BASE and
MSR_IA32_RTIT_OUTPUT_MASK_PTRS in ProcTraceSupport (executed by all
processors), and then use them in ProcTraceInitialize() for all
processors. This can also resolve the issue that the values of
OutputBaseReg.Uint64 and OutputMaskPtrsReg.Uint64 are not been
initialized in whole.
For TopaEntryPtr->Uint64, this patch updates code to initialize it
in whole explicitly by TopaEntryPtr->Uint64 = 0 before updating its
fields.
At the same time, this patch also eliminates the ProcTraceSupported
field in PROC_TRACE_PROCESSOR_DATA and the TopaMemArrayCount field in
PROC_TRACE_DATA.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1809
Current code disables TraceEn at the end of ProcTraceInitialize(),
then there will be much memory allocated even when ProcTrace feature
is disabled.
This patch updates code to disable TraceEn and return at the beginning
of ProcTraceInitialize() when when ProcTrace feature is disabled.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Cc: Kevin Li <kevin.y.li@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1679
The checking to CpuInfo->CpuIdVersionInfoEcx.Bits.AESNI is enough,
the checking to CPU generation could be removed, then the code
could be reused by more platforms.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
These files have \r\n line endings, but a few lines use \r\r\n which
is not a valid line ending. These lines were causing problems for git
and other tools.
Signed-off-by: Joe Richey <joerichey@google.com>
Review-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Add a new instance of the MpInitLib that is designed for
uniprocessor platforms that require the use of modules
that depend on the MP_SERVICES_PROTOCOL for dispatch
or to retrieve information about the boot processor.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
GetProcessorLocation2ByApicId() extracts the
package/die/tile/module/core/thread ID from the initial APIC ID.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Zhiqiang Qin <zhiqiang.qin@intel.com>
Cc: Ray Ni <Ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
PcdCpuFeaturesSupport used to specify the platform policy about
what CPU features this platform supports. This PCD will be used
in IsCpuFeatureSupported only.
Now RegisterCpuFeaturesLib use this PCD as an template to Get the
pcd size. Update the code logic to replace it with
PcdCpuFeaturesSetting.
BZ:https://bugzilla.tianocore.org/show_bug.cgi?id=1375
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
PcdCpuFeaturesUserConfiguration.
Merge PcdCpuFeaturesUserConfiguration into PcdCpuFeaturesSetting.
Use PcdCpuFeaturesSetting as input for the user input feature setting
Use PcdCpuFeaturesSetting as output for the final CPU feature setting
BZ:https://bugzilla.tianocore.org/show_bug.cgi?id=1375
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
V2 changes:
Update the commit message and comments in the code.
When waking vector buffer allocated by CpuDxe is tested by MemTest86
in MP mode, an error is reported because the same range of memory is
modified by both CpuDxe driver and MemTest86.
The waking vector buffer is not expected to be tested by MemTest86 if
it is allocated out because MemTest86 only tests free memory. But
current CpuDxe driver "borrows" buffer instead of allocate buffer for
waking vector buffer (through allocate & free to get the buffer
pointer, backup the buffer data before using it and restore it after
using). With this implementation, if the buffer borrowed is not used
by any other drivers, MemTest86 tool will treat it as free memory
and test it.
In order to fix the above issue, CpuDxe changes to allocate the
buffer below 1M instead of borrowing it. But directly allocating
memory below 1MB causes LegacyBios driver fails to start. LegacyBios
driver allocates memory range from
"0xA0000 - PcdEbdaReservedMemorySize" to 0xA0000 as Ebda Reserved
Memory. The minimum value for "0xA0000 - PcdEbdaReservedMemorySize"
is 0x88000. If LegacyBios driver allocate this range failed, it
asserts.
LegacyBios also reserves range from 0x60000 to
"0x60000 + PcdOpromReservedMemorySize", it will be used as Oprom
Reserve Memory. The maximum value for "0x60000 +
PcdOpromReservedMemorySize" is 0x88000. LegacyBios driver tries to
allocate these range page(4K size) by page. It just reports warning
message if some pages are already allocated by others.
Base on above investigation, one page in range 0x60000 ~ 0x88000 can
be used as the waking vector buffer.
LegacyBios driver only reports warning when page allocation in range
[0x60000, 0x88000) fails. This library is consumed by CpuDxe driver
to produce CPU Arch protocol. LagacyBios driver depends on CPU Arch
protocol which guarantees below allocation runs earlier than
LegacyBios driver.
Cc: Ray Ni <ray.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
.nasm file has been added for X86 arch. .S assembly code
is not required any more.
https://bugzilla.tianocore.org/show_bug.cgi?id=1594
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Shenglei Zhang <shenglei.zhang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
.nasm file has been added for X86 arch. .S assembly code
is not required any more.
https://bugzilla.tianocore.org/show_bug.cgi?id=1594
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Shenglei Zhang <shenglei.zhang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
.nasm file has been added for X86 arch. .S assembly code
is not required any more.
https://bugzilla.tianocore.org/show_bug.cgi?id=1594
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Shenglei Zhang <shenglei.zhang@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
BZ: https://bugzilla.tianocore.org/show_bug.cgi?id=1621
According to Intel SDM as below, the BIT0 should be treated as
lock bit, and BIT1 should be treated as disable(1)/enable(0) bit.
"11b: AES instructions are not available until next
RESET.
Otherwise, AES instructions are available.
If the configuration is not 01b, AES
instructions can be mis-configured if a privileged agent
unintentionally writes 11b"
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Chandana Kumar <chandana.c.kumar@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1020
Should make sure the TotalSize of Microcode is aligned with 4 bytes
before calling CalculateSum32 function.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1020
The Microcode region indicated by MicrocodePatchAddress PCD may contain
more than one Microcode entry. We should save InCompleteCheckSum32 value
for each payload. Move the logic for calculate InCompleteCheckSum32 from
the outsize of the do-while loop to the inside.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1576
The root cause of this issue is that non-stop mode of Heap Guard and
NULL Detection set TF bit (single-step) in EFLAG unconditionally in
the common handler in CpuExceptionLib.
If PcdCpuSmmStaticPageTable is FALSE, the SMM will only create page
table for memory below 4G. If SMM tries to access memory beyond 4G,
a page fault exception will be triggered and the memory to access
will be added to page table so that SMM code can continue the access.
Because of above issue, the TF bit is set after the page fault is
handled and then fall into another DEBUG exception. Since non-stop
mode of Heap Guard and NULL Detection are not enabled, no special
DEBUG exception handler is registered. The default handler just
prints exception context and go into dead loop.
Actually EFLAGS can be changed in any standard exception handler.
There's no need to do single-step setup in assembly code. So the fix
is to move the logic to C code part of page fault exception handler
so that we can fully validate the configuration and prevent TF bit
from being set unexpectedly.
Fixes: dcc026217f16b918bbaf
Test:
- Pass special test of accessing memory beyond 4G in SMM mode
- Boot to OS with Qemu emulator platform (Fedora27, Ubuntu18.04,
Windows7, Windows10)
Cc: Eric Dong <eric.dong@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Jian J Wang <jian.j.wang@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1521
Add information dump for Control Protection exception.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Yao Jiewen <jiewen.yao@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1020
The following Microcode payload format is define in SDM spec.
Payload: |MicrocodeHeader|MicrocodeBinary|ExtendedHeader|ExtendedTable|.
When we verify the CheckSum32 with ExtendedTable, we should use the fields
of ExtendedTable to replace corresponding fields in MicrocodeHeader,
and then calculate the CheckSum32 with MicrocodeHeader+MicrocodeBinary.
This patch already verified on ICL platform.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Chen A Chen <chen.a.chen@intel.com>
Cc: Ray Ni <ray.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Zhang Chao B <chao.b.zhang@intel.com>
Reviewed-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=1481
Today's MtrrLib contains a bug, for example:
when the original cache setting is WB for [0xF_0000, 0xF_8000) and,
a new request to set [0xF_0000, 0xF_4000) to WP,
the cache setting for [0xF_4000, 0xF_8000) is reset to UC.
The reason is when MtrrLibSetBelow1MBMemoryAttribute() is called the
WorkingFixedSettings doesn't contain the actual MSR value stored in
hardware, but when writing the fixed MTRRs, the code logic assumes
WorkingFixedSettings contains the actual MSR value.
The new fix is to change MtrrLibSetBelow1MBMemoryAttribute() to
calculate the correct ClearMasks[] and OrMasks[], and use them
directly when writing the fixed MTRRs.
Contributed-under: TianoCore Contribution Agreement 1.1
Signed-off-by: Ray Ni <ray.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Chasel Chiu <chasel.chiu@intel.com>
Ray Ni
Laszlo Ersek
John E Lofgren
Donald Kuo
Dong, Eric
Star Zeng
Zhichao Gao
Joe Richey
Michael D Kinney
Shenglei Zhang
Chen A Chen
Jian J Wang
Jiewen Yao
Ruiyu Ni