The code to detect what juno revision we are running on
is fairly small put it in a common header where it may be
used in a couple places.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The AXI<->PCIe translation comments are out of date with
respect to the code. In the first case the AXI master port
is incorrectly called a slave. In the second case the the
translation direction indicated for the slave port is the
wrong direction.
Correct both of these comments to reflect what the code is
doing.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The Juno PIO mapping is 8M, so it should be using a 32-bit
PIO address translation. Further, PIO addresses should start
at 0 and be translated to/from the ARM MMIO region.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Juno has several serial ports, one of which may be used for a remote
debug interface (e.g. gdb, WinDbg). The debug serial port needs to
be distinct from that used for UEFI trace to prevent corruption of
debugger protocol messaging.
The UEFI spec requires that serial devices be initialised to default
settings. (11.8 Serial I/O Protocol - "The default attributes for all
UART-style serial device interfaces are: 115,200 baud, ..."
and 17.3.3 EFI Debugport Variable - "These defaults must be used in the
absence of a DEBUGPORT variable...")
This change adds initialization of the serial device reported in the
ACPI DBG2 table. The initialisation is done early in the boot to allow
the possibility of remote debug of UEFI itself.
NOTE: This is functionally dependent on the DBG2 table being updated in
OpenPlatformPkg, but is required as a precursor to that change.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Switch all users of ArmLib that depend on the MMU routines to the new,
separate ArmMmuLib. This needs to occur in one go, since the MMU
routines are removed from ArmLib build at the same time, to prevent
conflicting symbols.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This module is now identical in functionality to NorFlashDxe, and is no
longer used, so remove it altogether.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Now that the generic Variable Runtime DXE code no longer distinguishes
between gEfiVariableGuid and gEfiAuthenticatedVariableGuid in the varstore
FV header, we can relax the check in the NOR flash driver to accept either
GUID regardless of whether we are running a secure boot capable build or not.
This also means we can always use gEfiAuthenticatedVariableGuid when we
encounter an empty NOR flash that needs to be initialized before use. So
remove the mNorFlashVariableGuid global from the shared code and from both
versions of NorFlashDxe.inf. This essentially collapses the two drivers into
a single one, which means we can remove NorFlashAuthenticatedDxe entirely
in a subsequent patch.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
This change corrects 3 problems in the PL011 driver.
1. The TRM states "The UARTLCR_H, UARTIBRD, and UARTFBRD registers must
not be changed:...when the UART is enabled"
2. The TRM (3.3.8) describes logic requiring the UART to be disabled and
flushed before adjusting UARTCR.
3. Several redundant calls get made to PL011UartInitializePort, where
the characteristics do not change, but updating the registers can
cause glitches in the output stream.
The parameters are compared to the current state and no action taken if
no change of state is required.
Where an update is required, the specified logic is followed, and the
register updates only made when the UART is disabled.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
On some platforms the UART clock is not the same for all the serial
ports. The PL011 driver must be capable of handling serial ports with
different clock rates, so must not rely on a PCD for the clock rate.
This patch allows the UART clock rate to be passed as a parameter
to PL011UartInitializePort(), which is called from the serial port
library. This patch also contains the corresponding changes in the
serial port library.
The PCD in Drivers/PL011Uart is replaced by an extra parameter for
PL011UartInitializePort. The PCD is moved to Library/PL011SerialPortLib
to supply the value to pass.
A corresponding patch to ArmVirtPkg is included in the same bundle to
align that with these changes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
The variable LineControl was initialised to zero, then updated in a
condition. This change converts that to a write in each branch of the
condition, removing the Write/Read/Modify/Write sequence.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
The PCDs used in the PL011 UART Driver and Serial Port Library are
inherently "fixed at build". This change updates the source to use
Fixed PCDs for these values. This improves clarity and efficiency.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
This cosmetic change only tidies things up in preparation for actual
updates. (This reflects responses to a previously submitted patch,
which has been split into several discrete changes.)
There are no functional changes in this commit.
Changes comprise:
Minor corrections to comment typos.
Minor formatting mods.
Expansion of function comments.
Remove OUT from UartBase parameter.
Addition of #define for "magic mumbers".
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Since the only reason for keeping a local copy mRT of the gRT pointer
is to be able to call GetVariable/SetVariable at runtime, use the
UefiRuntimeLib helpers instead, so that we can drop mRT altogether.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
PL031RealTimeClockLib is a base library that could potentially (although
unlikely) be incorporated into other modules than the DXE_RUNTIME_DRIVER
module that it was intended to complement.
This means the library has no business whatsoever setting the Runtime
Service table pointers directly (since we have no way of knowing which
instance will 'win', and the pointers may end up referring to a module
that is not a DXE_RUNTIME_DRIVER). So remove the assignment altogether.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
When combining UEFI firmware built from Tianocore with ARM Trusted
Firmware running in EL3, it is the responsibility of ATF that only
a single core enters the UEFI firmware in EL2, and the remaining cores
are released directly to the OS via PSCI SMC calls.
In this case, we don't need the MpCore flavor of PrePi or PrePeiCore,
but the UniCore flavor currently checks the CPU identification registers
directly, and refuses to proceed if the boot CPU is part of a MpCore
system.
So drop the ASSERT()'s that implement this check.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The PCI related PCDs are not platform specific, and architectural
protocols such as CpuIo2 are based on PCI provided MMIO to IO
translation, so these PCDs belong in ArmPkg not ArmPlatformPkg.
NOTE: this *WILL* break some out-of-tree platforms, the fix is changing
all consumers of gArmPlatformTokenSpaceGuid.PcdPci* to
gArmTokenSpaceGuid.PcdPci*
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The 64-bit version of the DS-5 debug script that retrieves the debug file
path from the PE/COFF image in memory assumes that the PE/COFF header is
packed, and that the debug directory entry in the optional header appears
at a fixed offset into the file. This is no longer true, now that we pad
between the file header and the PE header if the section alignment exceeds
the size of the header (which may be the case when the module contains a
vector table or small model code, which requires 2 KB or 4 KB section
alignment, respectively), to allow this padding to be emitted if the image
is subsequently converted to TE format.
So replace the fixed offset with a dereference of the appropriate header
field.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
This patch adds a PCD for the PL011 UART Interrupt as this is needed by
the Serial Port Console Redirection Table.
Code at: 68f26f23a2
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
This retypes some stack base PCD as 64-bit, and fixes up a number of references
to 64-bit PCDs (including the retypes ones), to use the correct PcdGet64()
accessors. Note that, in the case of FixedPcdGet64, this does not actually
caused any problems, since that resolves to an immediate value. But the
generic PcdGetxx accessors should be typed according to the size of the PCD.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leo Duran <leo.duran@amd.com>
[ard.biesheuvel: fixed up some instances in the 32-bit ARM code]
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Support multiple PL061 controllers. If platform gpio driver couldn't be
found, PL061 gpio driver will continue to load PcdPL061GpioBase as the
register base.
It could be compatible with the use case of current PL061 gpio driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
TC2 reads 0x02 for the PL180 ID3 register instead of 0x00 as defined in
the spec.
However, the spec [1] states that the contents of ID3 register represent
the "configuration option of the peripheral" and thus not part of the
Prime Cell identification.
For this patch, we drop checking the value in MCI_PERIPH_ID_REG3.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0172a/index.html
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
If the PL180 fails to probe, issue a warning on debug builds.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
PL180 on TC2 has a dependency on gEfiCpuArchProtocolGuid. Without
adding the dependency, TC2 will crash in the PL180 driver.
This problem has been present since d340ef7 when TC2 stopped booting.
However, it was masked by 300fc77 which prevented PL180 from running on
TC2 due to TC2 using a version on PL180 newer than that documented
publicly.
[1] https://github.com/tianocore/edk2/commit/d340ef7
2014-08-26
ArmPkg/ArmArchTimerLib: Remove non required [depex] and IoLib
[2] https://github.com/tianocore/edk2/commit/300fc77
2015-08-25
ArmPlatformPkg/PL180MciDxe: check PrimeCell ID before initializing
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
In the recent migration of the ARM Ltd. platforms to
https://git.linaro.org/uefi/OpenPlatformPkg.git, this file unfortunately
got left behind. Delete it to reduce confusion and (further) risk of
duplication of effort.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The PL061 GPIO controller is a bit of an anachronism, and the existing
driver does nothing to hide this - leading to it being very tricky to
read.
Rewrite it to document (in comments and code) what is actually
happening, and fix some bugs in the process.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
PL061Initialize() did not actually do anything other than call
PL061Identify() - so cut out the middle man.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
For whatever reason, every single operation on the PL061 looked for an
"Initialized" flag, and manually called the initialization function if
not set. Move this to a single call on protocol installation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
The copyright statement in PL061Gpio.c would not fit on a normal terminal
screen. Break lines at <= 80 characters.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Currently, we don't pick up removable media (USB drives) or storage
devices connected via plug-in cards. Take the sledge hammer approach
for now.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The Juno .dsc and .fdf files were recently deleted (currently held
in OpenPlatformPkg), but a spurious Makefile for building using it
was left in place. Drop the Makefile to complete the cleanup.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Harking back to the earliest days of software development for AArch64,
this piece of code abstracted away "early setup stuff" when the
software model came out of reset.
However, it is unmaintained and has been superseded by ARM Trusted
Firmware. So drop it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Juno is now managed in OpenPlatformPkg, including the ACPI
tables - so delete this unmaintained copy.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Ryan Harkin <ryan.harkin@linaro.org>
Juno doesn't have lots of DTB files in NOR flash, it only has 1 file,
called "board.dtb" and the motherboard configuration makes the right
choice about which DTB file gets written as board.dtb in NOR.
The code attempts to select which DTB it should use based on the board
variant or configuration. And this doesn't work because those DTB files
aren't present in NOR flash.
So remove the DTB variants and only load board.dtb.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Code was inserted to create default boot entries for Juno R1. These
don't work, but they are also preventing the board from booting into the
default options that Intel BDS would otherwise boot.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Setup the EFI System Table with information about the
Console Devices early, so that error messages in bds
are printed on the console earlier.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Supreeth Venkatesh <supreeth.venkatesh@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
The Sec library was built by the AARCH64 FVP models, but the binary was
unused because it was part of a legacy booting strategy from before ARM
Trusted Firmware came along.
This change requires changes in OpenPlatformPkg to remove the Sec binary
from the FVP build.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
This platform is untested and no longer supported, so remove it from the
tree.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
ARM Ltd Platform support is migrating to use OpenPlatformPkg [1].
Currently, Juno exists both in EDK2's ArmPlatformPkg and in
OpenPlatformPkg [2]. And they are starting to diverge, with
OpenPlatformPkg being the most up-to-date with current developments.
To prevent this divergence, remove the .dsc and .fdf files from
ArmPlatformPkg and leave OpenPlatformPkg as the master.
We can't remove ArmJuno.dec yet because ACPI still uses it to set the
include path to ArmPlatform.h.
[1] https://git.linaro.org/uefi/OpenPlatformPkg.git
[2] https://git.linaro.org/uefi/OpenPlatformPkg.git/tree/master:/Platforms/ARM/Juno
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
ARM Ltd Platform support is migrating to use OpenPlatformPkg [1].
Currently, FVP exists both in EDK2's ArmPlatformPkg and in
OpenPlatformPkg [2]. And they are starting to diverge, with
OpenPlatformPkg being the most up-to-date with current developments.
To prevent this divergence, remove the .dsc and .fdf files from
ArmPlatformPkg and leave OpenPlatformPkg as the master.
[1] https://git.linaro.org/uefi/OpenPlatformPkg.git
[2] https://git.linaro.org/uefi/OpenPlatformPkg.git/tree/master:/Platforms/ARM/VExpress
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
ARM Ltd Platform support is migrating to use OpenPlatformPkg [1].
Currently, TC2 exists both in EDK2's ArmPlatformPkg and in
OpenPlatformPkg [2]. And they are starting to diverge, with
OpenPlatformPkg being the most up-to-date with current developments.
To prevent this divergence, remove the .dsc and .fdf files from
ArmPlatformPkg and leave OpenPlatformPkg as the master.
[1] https://git.linaro.org/uefi/OpenPlatformPkg.git
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
The .dsc and .fdf files in ArmPlatformPkg are unused. Remove them as
part of a general cleanup of ArmPlatformPkg.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Problems have been encountered because some of the source files have
execute permission set. This can cause git to report them as changed
when they are checked out onto a file system with inherited permissions.
This has been seen using Cygwin, MinGW and PowerShell Git.
This patch makes no change to source file content, and only aims to
correct the file modes/permissions.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evan Lloyd <evan.lloyd@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19787 6f19259b-4bc3-4df7-8a09-765794883524
After fixing ArmGicEnableDistributor() in a previous patch, there is no
longer a reason to run the GICv3 in v2 mode, so remove the PCD override.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19275 6f19259b-4bc3-4df7-8a09-765794883524
The return_from_exception implementation in Sec/Helper.S (the GCC
version) deviates from the RVCT version, in a way that suggests that
both may have been broken at some point, and that they weren't fixed
in the same way nor at the same time.
So bring the GCC version in line with the RVCT version, and at the
same time, deobfuscate the comment.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19244 6f19259b-4bc3-4df7-8a09-765794883524
We can refer to gArmMpCoreInfoPpiGuid directly if we declare it under
[Ppis] in the library's .inf so there is no need to copy it into a
module local variable.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19243 6f19259b-4bc3-4df7-8a09-765794883524
We can refer to gArmMpCoreInfoPpiGuid directly if we declare it under
[Ppis] in the library's .inf so there is no need to copy it into a
module local variable.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19242 6f19259b-4bc3-4df7-8a09-765794883524
We can refer to gArmMpCoreInfoPpiGuid directly if we declare it under
[Ppis] in the library's .inf so there is no need to copy it into a
module local variable.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19241 6f19259b-4bc3-4df7-8a09-765794883524
We can refer to gArmMpCoreInfoPpiGuid directly if we declare it under
[Ppis] in the library's .inf so there is no need to copy it into a
module local variable.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19240 6f19259b-4bc3-4df7-8a09-765794883524
We can refer to gArmMpCoreInfoPpiGuid directly if we declare it under
[Ppis] in the library's .inf so there is no need to copy it into a
module local variable.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19239 6f19259b-4bc3-4df7-8a09-765794883524
This is the complementary patch for the commit 7945b29, which strictly
aligns temporary heap size and temporary stack size, but does not do
the same thing when switching stack and heap to permanent memory, and
then it may cause fatal data corruption like PHIT HOB lost and stack
pointer unaligned.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19213 6f19259b-4bc3-4df7-8a09-765794883524
Now that we removed the complete ArmPlatformGlobalVariable implementation,
remove stale PCD references to it from ArmVExpress-CTA15-A7.dsc
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19173 6f19259b-4bc3-4df7-8a09-765794883524
RVCT does not like the arithmetic involving a VOID* pointer that was
introduced in SVN r19163, so use explicit casts instead.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19172 6f19259b-4bc3-4df7-8a09-765794883524
Instead of using fuzzy arithmetic with a hardcoded stack alignment value
of 0x4, use the symbolic constant CPU_STACK_ALIGNMENT (which is at least
8 bytes, btw) to round the temporary stack base and size.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19163 6f19259b-4bc3-4df7-8a09-765794883524
Now that we removed all references to the ArmGlobalVariable definitions
in the various lowlevel PrePi and PrePeiCore init routines, and removed
the PPI and HOB references from PlatformPeim, it is time to say goodbye
to ArmGlobalVariable. So remove the includes and the .DEC declarations.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19003 6f19259b-4bc3-4df7-8a09-765794883524
PlatformIntelBdsLib does not use gArmGlobalVariableGuid so drop
the declaration from the .inf.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19002 6f19259b-4bc3-4df7-8a09-765794883524
EblCmdLib does not use anything that is declared by ArmGlobalVariableHob.h,
so remove the include.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19001 6f19259b-4bc3-4df7-8a09-765794883524
ArmVExpressFastBootDxe does not use gArmGlobalVariableGuid so drop
the declaration from the .inf.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19000 6f19259b-4bc3-4df7-8a09-765794883524
ArmJunoDxe does not use gArmGlobalVariableGuid so drop the declaration
from the .inf.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18999 6f19259b-4bc3-4df7-8a09-765794883524
Remove the GUID references to gArmGlobalVariableGuid and includes
of ArmGlobalVariableHob.h since they are not used by the ARM BDS.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18998 6f19259b-4bc3-4df7-8a09-765794883524
Now that we dropped all ArmPlatformGlobalVariableLib dependencies,
there is no longer a need to allocate and clear out the global
variable region in the Sec init code. So remove it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18995 6f19259b-4bc3-4df7-8a09-765794883524
Now that we dropped all ArmPlatformGlobalVariableLib dependencies,
there is no longer a need to allocate and clear out the global
variable region in the PrePeiCore init code. So remove it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18994 6f19259b-4bc3-4df7-8a09-765794883524
Now that we dropped all ArmPlatformGlobalVariableLib dependencies,
there is no longer a need to query the ArmGlobalVariable PPI and install
the ArmGlobalVariable HOB. So remove it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18993 6f19259b-4bc3-4df7-8a09-765794883524
Now that we dropped all ArmPlatformGlobalVariableLib dependencies,
there is no longer a need to allocate and clear out the global
variable region in the PrePi init code. So remove it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18992 6f19259b-4bc3-4df7-8a09-765794883524
This removes the SEC, PEI and DXE variants of ArmPlatformGlobalVariableLib,
which is no longer used, and should not be used since it violates the PI
spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18990 6f19259b-4bc3-4df7-8a09-765794883524
This removes the PeiServicesTablePointerLib implementation under
ArmPlatformPkg that violates the PI spec, and hence should not be
used. Instead, the implementation that resides under ArmPkg should
be used.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18989 6f19259b-4bc3-4df7-8a09-765794883524
We can remove all mention of ArmPlatformGlobalVariableLib now that
there are no remaining [transitive] dependencies on it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18988 6f19259b-4bc3-4df7-8a09-765794883524
As pointed out by Eugene, the ArmPlatformPkg implementation of
PeiServicesTablePointerLib violates the PI sec, since it uses
ArmPlatformGlobalVariableLib to store the PEI services table pointer
rather than the thread ID cpu registers as the spec requires.
So instead, move to the ArmPkg version of this library, which does
adhere to the PI spec.
Reported-by: Eugene Cohen <eugene@hp.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18987 6f19259b-4bc3-4df7-8a09-765794883524
This updates the PrePiHobListPointerLib implementation in ArmPlatformPkg
to move away from ArmPlatformGlobalVariableLib and instead use the thread
ID CPU registers (TPIDRURW and TPIDR_EL0 for v7 and v8, respectively)
for storing the HobList pointer.
Since PrePiHobListPointerLib is specific to PrePi (where PEI core is skipped)
we can share these registers with the PEI services table pointer. By the
same reasoning, the PEI services table pointer and the HobList pointer
already shared the same offset in the ArmPlatformGlobalVariable array.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18982 6f19259b-4bc3-4df7-8a09-765794883524
The PrePeiCore vector table for AArch64 mode is only half populated.
However unlikely, if exceptions from lower exception levels are ever
taken, they should be reported correctly, rather than causing a
recursive undefined instruction fault on the zero padding that was
introduced by commit SVN r18904 ("ArmPkg/ArmPlatformPkg: position
vectors relative to base"). So add the missing entries, and wire
them up to the default handler.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18976 6f19259b-4bc3-4df7-8a09-765794883524
We currently rely on .align directives to ensure that each exception
vector entry is the appropriate offset from the vector base address.
This is slightly fragile, as were an entry to become too large (greater
than 32 A64 instructions), all following entries would be silently
shifted until they meet the next alignment boundary. Thus we might
execute the wrong code in response to an exception.
To prevent this, introduce a new macro, VECTOR_ENTRY, that uses .org
directives to position each entry at the precise required offset from
the base of a vector. A vector entry which is too large will trigger a
build failure rather than a runtime failure which is difficult to debug.
For consistency, the base and end of each vector is similarly annotated,
with VECTOR_BASE and VECTOR_END, which provide the necessary alignment
and symbol exports. The now redundant directives and labels are removed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18904 6f19259b-4bc3-4df7-8a09-765794883524
Some users of this library (i.e., FVP-AArch64 and RTSM-A15_MPCore)
may be built to execute straight from NOR flash. Since device mappings
should have the XN attribute set (according to the architecture), mapping
the NOR flash as a device may prevent it from being executable.
Since the NOR flash DXE driver is perfectly capable of setting the correct
attributes for the region it needs to write to, and since we will be
executing from DRAM by that time anyway, we can simply map the NOR flash
as normal memory initially.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18890 6f19259b-4bc3-4df7-8a09-765794883524
The ARM and AARCH64 linker scripts have recently been updated so that
the memory layouts of the ELF and PE/COFF versions of each module are
identical. In particular, this means that the ELF images now have a
hole before the first section rather than starting at offset 0x0, which
means we no longer have to correct for this difference when loading the
ELF image into the debugger.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18775 6f19259b-4bc3-4df7-8a09-765794883524
The JunoR1 has a GICv2m which is a GICv2 with a little piece of hardware
that has some memory mapped locations that can trigger traditional SPI
interrupts. This allows some basic PCIe MSI capabilities.
Setup the SPI range that is mapped by the MSI window. This range is
described in the JunoR1 SoC TRM, table 3-3. Under Interrupt ID 244-351 is
described as "GICv2m PCI Express MSI". In the future when these tables
are generated programmatically the information may be found in the
MSI_TYPER register as well.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18723 6f19259b-4bc3-4df7-8a09-765794883524
These patches correct a number of problems with the JUNO ACPI tables.
First, put CCA attributes on the devices which can do DMA. This is
because the linux kernel now requires ARM64 devices specify a coherency
model. Without CCA the devices are unable to perform DMA.
Update the EHCI window to a full 64k as documented in the
Juno Platform SoC TRM. This makes it match the values used in some
other places.
Finally, add some _DSD entries for the SMSC ethernet chip.
The latter changes are required for the mainline kernels to use the adapter.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18628 6f19259b-4bc3-4df7-8a09-765794883524
All of AcpiSsdtRootPci.asl and some bits of Gtdt.aslc used LF-only
line separators. Fix before committing new modifications.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18627 6f19259b-4bc3-4df7-8a09-765794883524
The ValidateFvHeader() function checks several conditions against the
firmware volume header. Failure of the first of these checks, reported as
"No Firmware Volume header present", is a common situation for unformatted
flash images, especially when a new virtual machine is created.
Similarly, "Variable Store Guid non-compatible" is common when the
firmware binary is switched from Secure Boot-incapable to Secure
Boot-capable, or vice versa.
The only caller of ValidateFvHeader(), NorFlashFvbInitialize(), handles
all these mismatches by installing a new FVB header. It also emits
another, loud ERROR message (which is even less justified when it is
triggered by (BootMode == BOOT_WITH_DEFAULT_SETTINGS)).
Downgrade these messages from EFI_D_ERROR to EFI_D_INFO, so that they
don't clutter the debug output when the PcdDebugPrintErrorLevel mask only
enables EFI_D_ERROR (i.e., in a "silent" build).
These messages have annoyed / confused users; see for example:
- https://bugzilla.redhat.com/show_bug.cgi?id=1270279
- http://thread.gmane.org/gmane.comp.bios.edk2.devel/2772/focus=2869
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Drew Jones <drjones@redhat.com>
Cc: Yehuda Yitschak <yehuday@marvell.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18618 6f19259b-4bc3-4df7-8a09-765794883524
Currently the MADT signature and revision is mapped to v1.0 macros
which results in MADT with incorrect entries in the header for Juno.
This patch fixes these EFI_ACPI_*_0_MULTIPLE_APIC_DESCRIPTION_TABLE
macros by using appropriate v5.0 versions.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18572 6f19259b-4bc3-4df7-8a09-765794883524
These are no longer used by any platform in the tree, nor are they
of any significance to any out of tree platforms.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18571 6f19259b-4bc3-4df7-8a09-765794883524
In order to support the Properties Table memory protection feature
on 32-bit ARM, build DXE_RUNTIME_DRIVER type binaries with 4 KB section
alignment by setting the common-page-size linker command line option.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18567 6f19259b-4bc3-4df7-8a09-765794883524
For 32-bit ARM platforms, it is essential that system memory starts
below the 4 GB limit, since that is the only memory we can address
using the UEFI spec mandated 1:1 mapping. So assert that this is the
case.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18429 6f19259b-4bc3-4df7-8a09-765794883524
Make sure that the PEI memory region is carved out of memory that is
32-bit addressable, by taking MAX_ADDRESS into account (which is
defined as '4 GB - 1' on ARM)
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18426 6f19259b-4bc3-4df7-8a09-765794883524
Commit r18308 ("ArmPlatformPkg/LcdGraphicsOutputDxe: check PrimeCell ID
before initializing") introduced a LcdIdentify() function to the PL111
LCD driver that makes it fail gracefully when executed on hardware that
does not have the IP. However, the LcdGraphicsOutputDxe driver is shared
with the HdLcd driver, which now fails to build due to the fact that it
has no LcdIdentity() function. So add a dummy implementation that always
returns EFI_SUCCESS.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18395 6f19259b-4bc3-4df7-8a09-765794883524
Like the ArmVirtPkg platforms up until SVN r17713, the ArmPlatformPkg
platforms built with the Intel BDS fail to signal the end-of-DXE event
'gEfiEndOfDxeEventGroupGuid' when entering the BDS phase, which results
in some loss of functionality, i.e., variable reclaim in the VariableDxe
drivers, and the splitting of the memory regions that is part of the recently
added UEFI 2.5 properties table feature.
As discussed on the edk2-devel mailing list here:
http://thread.gmane.org/gmane.comp.bios.tianocore.devel/16088/focus=16109
it is up to the platform BDS to signal that event, since there may be
platform specific ordering constraints with respect to the signalling
of the event that are difficult to honor at the generic level.
So add the SignalEvent () call to PlatformBdsInit () of ArmPlatformPkg's
PlatformBdsLib implementation for the Intel BDS.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18394 6f19259b-4bc3-4df7-8a09-765794883524
This allows the FVP target to be built with UEFI Secure Boot enabled,
by passing -D SECURE_BOOT_ENABLE to the build command line. Note that
this requires the Intel BDS, or you will not be able to enroll
certificates, since the ARM BDS does not provide a GUI to do so.
The FVP Base model is recommended in this case, since the certificate
store is kept in NOR flash.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18379 6f19259b-4bc3-4df7-8a09-765794883524
This adds support for the Intel BDS and enables it by default.
To revert to using the ARM BDS, pass '-D USE_ARM_BDS' on the
build command line.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18378 6f19259b-4bc3-4df7-8a09-765794883524
Add a call to EnableQuietBoot () to BdsPlatformPolicyBehavior(),
so that a splash screen is shown in case one is present under the
correct GUID in the FV, and we have graphics support.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18377 6f19259b-4bc3-4df7-8a09-765794883524
InitializeConsolePipe () shadowed its own Status variable, and then
clobbered the top one before printing its error message. Instead,
use a NULL check on the LocateProtocol () output argument.
Also clean up coding style on the error path.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18376 6f19259b-4bc3-4df7-8a09-765794883524
The Intel BDS platform library still depends on the ARM BDS specific
BdsLib. So replace its invocations with GenericBdsLib counterparts,
and fix up where needed, so that we can drop the dependency.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18375 6f19259b-4bc3-4df7-8a09-765794883524
Now that the PL180 and PL111 drivers know how to behave when executed
on the Foundation model (which does not emulate the hardware), we can
remove the ARM_FOUNDATION_FVP ifdefs and produce a single build that
runs on both the Foundation model and the Base model.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18309 6f19259b-4bc3-4df7-8a09-765794883524
To deal gracefully with the absence of the PL111 hardware on
the Foundation model, check the PrimeCell ID before proceeding
with the installation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18308 6f19259b-4bc3-4df7-8a09-765794883524
To deal gracefully with the absence of the PL180 hardware on
the Foundation model, check the PrimeCell ID before proceeding
with the installation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18307 6f19259b-4bc3-4df7-8a09-765794883524
Remove the ARMGCC and ARMLINUXGCC from comments in the respective
Makefiles of ArmPlatformPkg and ArmJunoPkg. Also drop the wildly
outdated Versatile Express instructions, since they refer to ARMGCC
as well.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18209 6f19259b-4bc3-4df7-8a09-765794883524
Now that GenFw correctly propagates the minimum alignment of the ELF
input sections to the PE/COFF binary, we can simply select 'auto'
alignment in the FDF Rule section instead of tweaking it by hand.
Also add the FIXED FFS attribute to the module types that may execute
in place. This enables a newly added optimization in GenFfs that strips
redundant padding, preventing excessive waste of FV space if the section
alignment is considerable (i.e., 2 KB or 4 KB)
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18196 6f19259b-4bc3-4df7-8a09-765794883524
No need to hardcode the TE alignment anymore, now that GenFw sets
the PE/COFF alignment according to the alignment requirements of
the ELF input sections.
Also enable FIXED FFS placement so that we can reclaim some of the
space wasted to padding when using clang with 4 KB section alignment.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18195 6f19259b-4bc3-4df7-8a09-765794883524
The ACPI .aslc files contain a ReferenceAcpiTable() function whose
sole purpose is to ensure that the table itself does not get optimized
away. However, when using clang, these dummy functions result in a 4 KB
section alignment requirement, which is silly since everything except
the .data section is discarded later anyway.
So instead, make ReferenceAcpiTable a CONST pointer to VOID*. This way,
we still have a .text section, which is mandatory for the PE/COFF
conversion, but no executable code with small model relocations that
impose additional alignment requirements.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18194 6f19259b-4bc3-4df7-8a09-765794883524
Make global EFI_PEI_PPI_DESCRIPTOR instances CONST to prevent them
from being emitted into the .data section.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18189 6f19259b-4bc3-4df7-8a09-765794883524
Since PrePeiCore's .text section contains an AARCH64 exception
vector table, its 2 KB alignment propagates to other sections as
well. Since this is a SEC module, it should not have any writable
data in the first place, so change some non-const PPI globals to
const. The resulting binary has no .data section at all, which
saves 2 KB in the XIP image.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18188 6f19259b-4bc3-4df7-8a09-765794883524
Move to the parametrised generic GCC linker script and set 64 KB
alignment, instead of using the AARCH64 specific incremental linker
script for 64 KB alignment which is about to be removed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18139 6f19259b-4bc3-4df7-8a09-765794883524
Remove obsolete ARM and AARCH64 platforms so the maintainers can
focus on the ones that are still supported, which are:
- TC2 (ArmVExpress-CTA15-A7.dsc)
- Foundation model and Fast model emulators (ArmVExpress-FVP-AArch64.dsc)
- Juno (ArmJunoPkg/ArmJuno.dsc)
- Cortex-A15 MPcore RTSM (ArmVExpress-RTSM-A15_MPCore)
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18110 6f19259b-4bc3-4df7-8a09-765794883524
Clone ArmGicArchLib into a SEC phase specific ArmGicArchSecLib
so that we can modify the former in a subsequent patch to cache
the GIC revision in a global variable.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18099 6f19259b-4bc3-4df7-8a09-765794883524
The current implementation of ArmGicGetSupportedArchRevision ()
that is used by all ARM platforms is entirely stateless (in order
to support being executed from flash) so it needs to interrogate
the hardware for the supported GIC revision upon each invocation.
However, this statelessness is only needed for SEC type modules;
in all other cases, we could easily determine the GIC revision once,
and store the result in a global variable.
In preparation of having separate early and normal versions, this patch
introduces the ArmGicArchLib library class and default implementation,
and moves the existing ArmGicGetSupportedArchRevision () into it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18098 6f19259b-4bc3-4df7-8a09-765794883524
LocateProtocol only gets the 1st SNP instance and this will be wrong
in a system with multiple SNP instances installed. Use HandleProtocol
instead.
Cc: Olivier Martin <olivier.martin@arm.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Reviewed-by: Olivier Martin <Olivier.Martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18030 6f19259b-4bc3-4df7-8a09-765794883524
Recent changes have made the A15-A7 firmware bigger...
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18029 6f19259b-4bc3-4df7-8a09-765794883524
There are still ARM/AArch64 Linux kernels that do not support EFI Stub.
By using the EFI Linux loader as the default option we can boot any
Linux kernel from UEFI as Linux kernel with EFI stub can also be
booted with the legacy way.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17975 6f19259b-4bc3-4df7-8a09-765794883524
When PcdBdsLinuxSupport is enabled, users can create boot
entries for the legacy EFI Linux loader.
The ARM BDS detects if the image is a EFI image if not
then it assumes it is a legacy Linux kernel (a kernel
without EFI Stub).
If the Boot Manager did not manage to load the binary
(it could happen when the binary is on the network or
not present on the media yet).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17974 6f19259b-4bc3-4df7-8a09-765794883524
The Linux Loader has been removed from ARM BDS. These PCDs
are not needed anymore.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17973 6f19259b-4bc3-4df7-8a09-765794883524
PcdDefaultBootType has been removed when the embedded
Linux Loader has been removed from BdsLib.
The boot arguments (defined by PcdDefaultBootArgument)
are now always targetting EFI applications.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17971 6f19259b-4bc3-4df7-8a09-765794883524
Since the embedded Linux Loader has been removed from BdsLib
there is no more Linux specific boot option.
All the boot options are now expected to be arguments for
EFI applications.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17970 6f19259b-4bc3-4df7-8a09-765794883524
This change removes the embedded Linux Loder from BdsLib.
BdsLib becomes OS agnostic.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17969 6f19259b-4bc3-4df7-8a09-765794883524
Add the legacy Linux Loader EFI application to the ARM
development platforms.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <Ronald.Cron@arm.com>
Reviewed-by: Olivier Martin <Olivier.Martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17968 6f19259b-4bc3-4df7-8a09-765794883524
Replaced the function BdsLoadApplication() by two explicit
functions that load the EFI application either by its GUID
or its Name.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17966 6f19259b-4bc3-4df7-8a09-765794883524
The PSCI specification covers both ARM and AARCH64, however, the
ARM Trusted Firmware (ATF) reference implementation is only available
for AARCH64, and PSCI firmware is not widely available for ARM platforms.
So use the EfiResetSystemLib implementation that uses PSCI calls only
on AARCH64, and revert to the Versatile Express-specific system register
interface (which is only available during boot time) on ARM platforms.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17927 6f19259b-4bc3-4df7-8a09-765794883524
Instead of using a NULL implementation of ArmPlatformSysConfigLib for
DXE_RUNTIME_DRIVER modules, which prevents them from accessing system
control registers even at boot time, use the new implementation that
only switches into a non-functional mode at runtime, and operates as
before otherwise.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17926 6f19259b-4bc3-4df7-8a09-765794883524
This adds a ArmPlatformSysConfigLib implementation that is usable by
DXE_RUNTIME_DRIVER modules. Since the system registers that this library
encapsulates are not usable at runtime, this driver allows access to
those registers only at boot time.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17925 6f19259b-4bc3-4df7-8a09-765794883524
Ip4ConfigDxe driver is deprecated in UEFI 2.5, so we will not support original Ip4Config Protocol,
which is replace by Ip4Config2 Protocol integrated in Ip4Dxe driver(git commit 1f6729ff (SVN r17853)).
Therefore we can remove Ip4ConfigDxe driver from this build.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17911 6f19259b-4bc3-4df7-8a09-765794883524
This reverts commit SVN rev17862.
The former commit was breaking the build when DTB_DIR is defined.
It has been the patch would be reverted for the time being.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17889 6f19259b-4bc3-4df7-8a09-765794883524
The linker script is specific to GCC toolchain.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17864 6f19259b-4bc3-4df7-8a09-765794883524
On the FVP base and foundation models, the default file name
used to retrieve the FDT depended on the values assigned to
model parameters (GIC related model parameters).
Now, in addition to the fallback "fdt.dtb" file name (used for legacy
reason), only one default file name is used :
- "fvp-base.dtb" for the base model.
- "fvp-foundation.dtb" for the foundation model.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17862 6f19259b-4bc3-4df7-8a09-765794883524
This fixes the declaration and definition of mSystemMemoryEnd so that it
is correctly annotated as a non-function symbol. Also adds the ASM_PFX
prefix, which is empty on AARCH64 but should be included for correctness.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17860 6f19259b-4bc3-4df7-8a09-765794883524
This adds the 64 KB alignment overlay linker script to the linker command
line of DXE_RUNTIME_DRIVER modules built for AARCH64. This makes these
modules compatible with the new Properties Table feature by aligning the
.text and .data sections to 64 KB.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17836 6f19259b-4bc3-4df7-8a09-765794883524
This change allows to change the top of the System Memory that
was hardcoded by:
FixedPcdGet64 (PcdSystemMemoryBase) + FixedPcdGet64 (PcdSystemMemorySize)
It allows to add support when the Trusted Firmware reserves the
top of the System Memory as Trusted. The size of this region
might not be known in advance.
Note: The reason why the start of the System Memory has not been
made dynamic is because the early code calculates where to place
the stack from the top of the System Memory.
So there is no need to make the start of the System Memory a
dynamic value at the early stage of the boot phase.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17835 6f19259b-4bc3-4df7-8a09-765794883524
The PlatformLib could have declared the resource hob for
the main system memory region.
This change would prevent to get this system memory resource
to be declared twice.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17834 6f19259b-4bc3-4df7-8a09-765794883524
PcdFirmwareVersionString is defined in MdeModulePkg to be
either fixed or dynamic, but is restricted in ArmPlatformPkg
drivers to FixedPcd. Changed to remove the FixedPcd
restrictions to allow platforms to chose the correct type
in their DSC files.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Samer El-Haj-Mahmoud <samer.el-haj-mahmoud@hp.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17833 6f19259b-4bc3-4df7-8a09-765794883524
We use the NorFlash file system to read the
Device Tree from.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17831 6f19259b-4bc3-4df7-8a09-765794883524
Filenames cannot be longer than 8-character long on
ARM Versatile Express.
Use the default DTB filenames (the ones provided by
the ARM Versatile Express DVD) for the different Core
Tile.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17830 6f19259b-4bc3-4df7-8a09-765794883524
The A15-A7 FVP model was previously the default build.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17829 6f19259b-4bc3-4df7-8a09-765794883524
By default, a MemoryMap() EFI Device Path is created
for the Firmware Volumes.
It means it is difficult to build a Non-Volatile permanent
Device Path for the Firmware Volume as the location in
System Memory may change.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17827 6f19259b-4bc3-4df7-8a09-765794883524
People has requested this feature to be restaured in the
ARM Boot Manager.
The configuration from the EFI Shell is always possible
and it is the recommended approach to update the FDT
Device Path.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <Ronald.Cron@arm.com>
Reviewed-by: Olivier Martin <Olivier.Martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17826 6f19259b-4bc3-4df7-8a09-765794883524
Remove gVariableAuthenticatedRuntimeDxeFileGuid definition in
ArmPlatformPkg.dec and use gVariableRuntimeDxeFileGuid in
NorFlashAuthenticatedDxe.inf as auth Variable driver in SecurityPkg
and Variable driver in MdeModulePkg have been merged.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17768 6f19259b-4bc3-4df7-8a09-765794883524
These library classes are now linked with
MdeModulePkg/Universal/Variable/RuntimeDxe/VariableRuntimeDxe.inf
to optionally support secure variables.
For ArmPlatformPkg, secure boot is not currently enabled,
so we map these libraries to the NULL versions that don't support secure variables.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17762 6f19259b-4bc3-4df7-8a09-765794883524
The PCI Root bridge is defined by PciRoot(0x0)/Pci(0x0,0x0).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17528 6f19259b-4bc3-4df7-8a09-765794883524
1. Data type for GcdMemoryType and GcdIoType is enumeration type
rather than bit field, so we need to use strict equation "=="
instead of bit-and "&";
2. Testing for GcdIoType should use EfiGcdIoType*** constants
rather than EfiGcdMemoryType***;
3. As we are going to use strict equation, it is clearer to use
switch-case than if-else.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Reviewed-by: Olivier Martin <Olivier.Martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17527 6f19259b-4bc3-4df7-8a09-765794883524
... since gEfiMdePkgTokenSpaceGuid.PcdPlatformBootTimeOut has recently
been introduced.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17443 6f19259b-4bc3-4df7-8a09-765794883524
PCI support is only present on Juno R1.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17415 6f19259b-4bc3-4df7-8a09-765794883524
Since there is now a formal definition of EFI_LOAD_OPTION, we can no
longer typedef it as a UINT8*. So update the code to use the common
definition, which is not a pointer type, hence the additional changes
to the C code.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17410 6f19259b-4bc3-4df7-8a09-765794883524
Since ArmVExpressSysConfigLib cannot be supported at runtime, restrict
its use to the types of modules that are currently using it legally.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17382 6f19259b-4bc3-4df7-8a09-765794883524
The ArmVExpressSysConfigLib library does not (and cannot) runtime
remap its MMIO registers, so use a NULL implementation of the
ArmPlatformSysConfigLib library class for DXE_RUNTIME_DRIVER
type modules.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17381 6f19259b-4bc3-4df7-8a09-765794883524
Since the default EfiResetSystemLib for VExpress cannot be used at
runtime (due to the fact that its MMIO registers need to be owned
by the OS and so cannot be runtime remapped), instead use PSCI calls
into EL3 at runtime.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17380 6f19259b-4bc3-4df7-8a09-765794883524
If DTB_DIR=<path> is set during the build, incorporate DTBs from
that path for all AArch64 FVP platform variants so that they can
be loaded straight from the firmware image instead of from a file
system. This relieves a user of having to keep a DTB file with the
right name in the working directory of the model.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17360 6f19259b-4bc3-4df7-8a09-765794883524
This adds support to the ArmVExpressPkg platforms to load their
device tree binary from a Firmware Volume if one is found that
matches the current platform. If none is found, the existing
logic to find a FDT by name from a file system is retained as
a fallback.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17359 6f19259b-4bc3-4df7-8a09-765794883524
Instead of using open coded GUIDs, define them only once, and refer
to them by name everywhere else.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17358 6f19259b-4bc3-4df7-8a09-765794883524
This adds all the required modules and library dependencies so that
the ArmVirtualizationQemu platform can be built with support for
UEFI Secure Boot. This support consists of the OpenSSL crypto
library (whose source needs to be downloaded separately), the
authenticated variable store, and authentication of executables
before launching them.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17356 6f19259b-4bc3-4df7-8a09-765794883524
The NorFlashDxe uses an explicit 'BEFORE xxx' Depex declaration to
ensure that it is dispatched before VariableRuntimeDxe, and uses the
file GUID of the latter as 'xxx' explicitly to accomplish that.
However, when enabling UEFI Secure Boot, this breaks down since the
authenticated VariableRuntimeDxe is a completely separate driver, with
a different GUID. Also, the hardcoded dependency on gEfiVariableGuid,
which is not used under UEFI Secure Boot, needs to be factored out in
order to allow this driver to be used.
So clone NorFlashDxe.inf into NorFlashAuthenticatedDxe.inf, and fix
up the dependencies so they refer to gEfiAuthenticatedVariableGuid and
SecurityPkg/VariableAuthenticated/RuntimeDxe/VariableRuntimeDxe.inf
instead.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17355 6f19259b-4bc3-4df7-8a09-765794883524
We keep UID=0 for the 'real' PCI root complex on the Juno board.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17342 6f19259b-4bc3-4df7-8a09-765794883524
PcdOverridePlatformFdt was set with its default value.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17306 6f19259b-4bc3-4df7-8a09-765794883524
The Fdt platform driver has been moved at the end of the list
of the DXE/UEFI drivers to ensure the device drivers have been
dispatched prior to load the FDT platform driver.
For instance, if we want to load FDT from TFTP we must have
the ethernet driver to be already loaded.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17305 6f19259b-4bc3-4df7-8a09-765794883524
Other libraries/modules could use it (eg: EFI Shell command `runaxf`).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17297 6f19259b-4bc3-4df7-8a09-765794883524
Some ARM development platforms use ARM Trusted Firmware to boot.
ARM Trusted Firmware encapsulates UEFI into the FIP (Firmware
Image Package) binary.
This change allows to update the FIP binary after building UEFI.
Example to build UEFI for FVP Base model:
$ make -f ArmPlatformPkg/Scripts/Makefile \
EDK2_DSC=ArmPlatformPkg/ArmVExpressPkg/ArmVExpress-FVP-AArch64.dsc \
EDK2_ARCH=AARCH64 EDK2_TOOLCHAIN=GCC49 \
FIP_BIN=~/arm-trusted-firmware/build/fvp/release/fip.bin
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17296 6f19259b-4bc3-4df7-8a09-765794883524
In order to prevent memory corruption issues caused by the fact that,
under virtualization, the guest is incoherent with the hypervisor's view
of memory until it enables its caches and MMU, this patch reshuffles the
init sequence so that the Xen shared memory regions are not touched
before the caches and MMU are enabled.
In addition, the loaded image itself is invalidated by virtual address,
to ensure that any runtime changes (such as the applied relocations) will
not suddenly become invisible once we turn the caches on.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Olivier Martin <Olivier.Martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17178 6f19259b-4bc3-4df7-8a09-765794883524
This updates ArmVirtualizationMemoryInitPeiLib so that the PEI memory
region, i.e., the region that is used both before and after the MMU
and caches are enabled, is invalidated by virtual address before
enabling the MMU.
This prevents issues where data we modified with the caches and MMU
off may be shadowed by clean cachelines in system caches or in lower
level caches on other CPUs, resulting in the this data to become
invisible once we turn the MMU and caches on.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17177 6f19259b-4bc3-4df7-8a09-765794883524
MemoryInitPeim short-circuits its MemoryInitPeiLib dependency by including
the .c file directly. This prevents us from having a special implementation
for ArmVirtualizationPkg that performs additional cache maintenance before
enabling the MMU. So instead, make it depend on the library class.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17175 6f19259b-4bc3-4df7-8a09-765794883524
This updates ArmVirtualization.dsc.inc to use the MemoryInitPeiLib
implementation for virt targets. The only difference between that one
and the original one is that the original one removes memory from the
available list if it overlaps the FD region (which may be the case when
shadowing NOR flash with system RAM). This is never the case for the
Qemu target, which is the only platform affected by this change, since
the Xen target already uses this library explicitly.
This allows us to remove the Xen-specific declaration of this library
dependency. For the Qemu target, this change will not take effect until
after the MemoryInitPeim<->MemoryInitPeiLib dependency resolution is
fixed in a subsequent patch.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17174 6f19259b-4bc3-4df7-8a09-765794883524
LzmaDecompress support is moving from IntelFrameworkPkg to
MdeModulePkg.
This change ensures ArmPlatformPkg reflects this future change.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ronald Cron <ronald.cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17133 6f19259b-4bc3-4df7-8a09-765794883524
The default name should match the legacy Juno R0 name (ie: juno.dtb)
to ensure the updated UEFI firmware still works on the deployed Juno R0
board.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17097 6f19259b-4bc3-4df7-8a09-765794883524
On Juno R1, the MAC address assigned to the PCI Gigabyte Ethernet device
as to be passed to the Linux Kernel.
The MAC address is passed to the Linux Kernel by means of the boot argument
"sky2.mac_address".
This patch adds this boot argument to the lists of boot arguments of the
two Juno R1 default boot options.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <ronald.cron@arm.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17095 6f19259b-4bc3-4df7-8a09-765794883524
This is a copy/paste of the exact same code in both cases: Buffer
should only be freed on the success path, otherwise it will be
NULL
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ronald Cron <Ronald.Cron@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17078 6f19259b-4bc3-4df7-8a09-765794883524
The "virt" machine type of qemu-system-(arm|aarch64) had no PCIe support
prior to qemu commit
4ab29b82 arm: Add PCIe host bridge in virt machine
With that commit, the "virt" board acquired the capability to expose an
XHCI controller. Using a USB keyboard as example, the command line options
were
-device nec-usb-xhci -device usb-kbd
However, due to a slight XHCI emulation bug in QEMU -- dating back to
several years earlier -- edk2's XHCI driver would encounter a failed
ASSERT().
This emulation problem has been fixed in QEMU commit
aa685789 xhci: generate a Transfer Event for each Transfer TRB with the
IOC bit set
and now edk2's XHCI driver works well on QEMU's "nec-usb-xhci" device.
Let's enable the driver in ArmVirtualizationQemu, as XHCI emulation is
reportedly more virtualization-friendly than EHCI, consuming less CPU.
(ArmVirtualizationXen is not modified because it includes no USB-related
drivers at all.)
This patch should not regress existing QEMU command lines (ie. expose the
failed ASSERT()) because QEMU's "-device nec-usb-xhci" has never before
resulted in USB devices that worked with edk2 firmware builds, hence users
have never had a reason to add that option.
Now that they learn about XHCI support in ArmVirtualizationQemu by reading
this commit message, they (or their packagers) will also know to update
qemu to aa685789 or later (in practice that means the upcoming 2.3
release), at least if they want to use '-device nec-usb-xhci' with edk2,
for the first time ever.
Cc: Leif Lindholm <Leif.Lindholm@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Alexander Graf <agraf@suse.de>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17053 6f19259b-4bc3-4df7-8a09-765794883524
Including a prebuilt shell executable in the firmware binary is suboptimal
practice, especially given that the source code of the UEFI shell resides
in the same edk2 tree. Benefits of building the shell from source are
partly technical (a developer patching the shell can actually see the
results), partly ideological (the nominally built-from-source firmware is
actually built from source). "Security" might be worth a mention too.
The stanza for the [Components.common] section of
"ArmVirtualization.dsc.inc" originates from under OvmfPkg.
Cc: Leif Lindholm <Leif.Lindholm@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17052 6f19259b-4bc3-4df7-8a09-765794883524
Perform the following renames in order to stick with edk2 tradition more
closely:
XenHypercallLibArm, XenHypercallLibIntel -> XenHypercallLib
XenHypercallIntel -> X86XenHypercall
In addition, we unify the INF files.
This patch modifies ArmVirtualizationPkg and OvmfPkg at once, in order to
keep both bisectable (client code shouldn't break).
Suggested-by: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16998 6f19259b-4bc3-4df7-8a09-765794883524
This enables -D DEBUG_PRINT_ERROR_LEVEL=0x8040004F style command line
options.
Since we're massaging the debug message bitmask anyway, let's update the
description of the individual bits too in the comments, so that they match
"MdePkg/Include/Library/DebugLib.h".
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16986 6f19259b-4bc3-4df7-8a09-765794883524
When the user doesn't pass a kernel with QEMU's "-kernel" switch, the
firmware sees a zero-sized kernel blob via the QemuFwCfgItemKernelSize
key; there's no way to distinguish "no kernel" from "zero sized kernel".
In both cases TryRunningQemuKernel() proceeds as far as gBS->LoadImage(),
which then rejects the zero sized synthetic file with EFI_UNSUPPORTED.
This is known and works fully as expected; however we should rather catch
the much more frequent "no kernel" case earlier, in order to avoid the
EFI_D_ERROR message
TryRunningQemuKernel: LoadImage(): Unsupported
which is arguably meaningless noise for the "no kernel" case.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16985 6f19259b-4bc3-4df7-8a09-765794883524
This adds the .dsc and .fdf descriptions to build a UEFI image that
is bootable by a Xen guest on 64-bit ARM (AArch64)
Contributed-under: TianoCore Contribution Agreement 1.0
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16981 6f19259b-4bc3-4df7-8a09-765794883524
This patchs adds support to VirtFdtDxe for the Xen DT node which
contains the base address of the Grant Table. This data is communicated
to XenBusDxe using a XENIO_PROTOCOL instance.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16980 6f19259b-4bc3-4df7-8a09-765794883524
This implements a dummy RealTimeClockLib for Xen, as there is no
guest interface to access the time kept by Xen that can be shared
between UEFI and the OS.
Contributed-under: TianoCore Contribution Agreement 1.0
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16977 6f19259b-4bc3-4df7-8a09-765794883524
Add a ArmPlatformLib instance that can deal with the self relocation
and truly dynamic discovery of system RAM base and size.
Contributed-under: TianoCore Contribution Agreement 1.0
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16964 6f19259b-4bc3-4df7-8a09-765794883524
Allow the use of patchable PCDs for gArmTokenSpaceGuid.PcdFvBaseAddress
and gArmVirtualizationTokenSpaceGuid.PcdDeviceTreeInitialBaseAddress
by moving them from the [FixedPcd] to the [Pcd] section in the INF file of
PlatformPeiLib.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16963 6f19259b-4bc3-4df7-8a09-765794883524
This implements a MemoryInitPeiLib instance that differs from the
stock ArmPlatformPkg version only in the fact that it does not remove
the memory used by the flash device (FD). The reason is that, when using
PrePi, the DXE core is started immediately and never returns so there is
no reason to preserve any of the memory that the flash device occupied
originally, and it is preferable to release is so that the OS loader
can reuse it. This is especially important for the relocatable PrePi
configuration, which is aimed at being launched from a boot loader that
itself adheres to the Linux arm64 boot protocol.
Contributed-under: TianoCore Contribution Agreement 1.0
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Olivier Martin <olivier.martn@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16962 6f19259b-4bc3-4df7-8a09-765794883524
This patch introduces a relocatable PrePi, which can execute
from arbitrary offsets in RAM. This is intendend to be run
from a boot loader which passes a description of the actual
platform in a device tree, for instance.
This module is based on the PrePi implementations residing under
ArmPlatformPkg.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16961 6f19259b-4bc3-4df7-8a09-765794883524
Our primary user QEMU/mach-virt presents us with a FDT blob padded
to 64 KB with plenty of room to set additional properties. However,
in the general case, we should only add properties after making sure
there is enough room available.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16960 6f19259b-4bc3-4df7-8a09-765794883524
Instead of using a dynamic PCD, store the device tree address in a HOB
so that we can also run under a configuration that does not support
dynamic PCDs.
This also adds MemoryAllocationLib to the [LibraryClasses] section of
ArmVirtualizationPlatformLib/ArmVirtualizationPlatformLib.inf, as this
dependency was formerly satisfied transitively through one of the
library dependencies that were dropped.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16959 6f19259b-4bc3-4df7-8a09-765794883524
This is partially motivated by the desire to use PrePi in a virt
environment, and in that configuration, ArmPlatformInitializeSystemMemory()
is never called. But actually, this is a more suitable place anyway.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16958 6f19259b-4bc3-4df7-8a09-765794883524
To allow a runtime self relocating PrePi instance to discover the base
address of the device tree at runtime, allow the use of a patchable PCD
for gArmVirtualizationTokenSpaceGuid.PcdDeviceTreeInitialBaseAddress.
We will not be using the build time patch tool in this case, but using
a patchable PCD will make the build system aware that its value is not
a compile time constant.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16957 6f19259b-4bc3-4df7-8a09-765794883524
This adds support for detecting the presence of a GICv3 interrupt
controller from the device tree, and recording its distributor and
redistributor base addresses in their respective PCDs.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16956 6f19259b-4bc3-4df7-8a09-765794883524
This moves the reference to gArmTokenSpaceGuid.PcdFdBaseAddress
from the [FixedPcd] to the [Pcd] section in the INF file of
PrePiArmPlatformGlobalVariableLib so that its users may choose
to use a patchable PCD instead.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16955 6f19259b-4bc3-4df7-8a09-765794883524
The DT binding for the ARM generic timer describes the secure,
non-secure, virtual and hypervisor timer interrupts, respectively.
However, under virtualization, only the virtual timer is usable, and
the device tree may omit the hypervisor timer interrupt. (Other timer
interrupts cannot be omitted simply due to the fact that the virtual
timer is listed third)
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16953 6f19259b-4bc3-4df7-8a09-765794883524
Juno R1 can run in two configurations:
- A57x2
- A57x2-A53x4
The Device Tree tell Linux which configuration has been selected.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16942 6f19259b-4bc3-4df7-8a09-765794883524
Remove the option to update the "Fdt" UEFI variable in the ARM BDS as
the "setfdt" EFI Shell command provides this service from now.
Remove the use of this variable in the legacy kernel boot loader and
use the FDT installed in the configuration table instead.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <Ronald.Cron@arm.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16940 6f19259b-4bc3-4df7-8a09-765794883524
Jeremy Linton
Evan Lloyd
Ard Biesheuvel
Sami Mujawar
Leendert van Doorn
Haojian Zhuang
Ryan Harkin
Leif Lindholm
Supreeth Venkatesh
Jordan Justen
Heyi Guo
Star Zeng
Mark Rutland
Laszlo Ersek
Sudeep Holla
Olivier Martin
Ronald Cron
Jiaxin Wu
Samer El-Haj-Mahmoud
Ruiyu Ni